PDA

View Full Version : what SOIC8 is this 95M01WT, K430K??


lwood
24th April, 2015, 11:49 PM
i am working on a 2014 Toyota Corolla 89170-02G60
the SOIC8 chip inside has numbers i have never seen..
here is the chip info 95M01WT, K430K.. could someone tell me what chip it is??
i try google with no luck.
i remove chip read as the following with no lcuk 95320, 95640, 95160
repairmymodule
25th April, 2015, 12:11 AM
I can't help you decode mask but if it does not have SPC560 MCU than the soic eeprom may be 93Cxx series. Look close at MCU to see if it is an SPC560
auto80
25th April, 2015, 12:14 AM
post photos from both sides
lwood
25th April, 2015, 12:20 AM
Renesas 1727
luis12
14th January, 2016, 11:49 PM
Friend I have one of this module, same ask as you, Tachosoft tells read ST95M01 but how it is readed, thanks.
SrsRobot
15th January, 2016, 12:28 AM
DreamPro3 programmer .. 20$ on Ali, I use Sofi-Tech on them couple more bucks ...
Plcautoparts
15th January, 2016, 01:55 AM
95M01WT is the correct eeprom,carprog and orange can read it , orange much faster!!
SrsRobot
15th January, 2016, 02:55 AM
Use the universal programmers that I listed and read as M95M01...
luis12
15th January, 2016, 04:02 PM
I can read it with Xeltec Pro as 95256/95320/95640 all of this make Reading but dont know if correct number of Bytes, in Orange wich is the last line ? Xeltec last lines if read as 95256 or 95320 is 7FF0 and 32Kb.
SrsRobot
15th January, 2016, 04:08 PM
Its 1mb eeprom, I checked and I dont have old dump to compare size or content Sorry
credoline
15th January, 2016, 06:40 PM
You must select eeprom like 95M01, you can not use other type instead this one. Cheap clone of SEEprog is best solution for you.


I can read it with Xeltec Pro as 95256/95320/95640 all of this make Reading but dont know if correct number of Bytes, in Orange wich is the last line ? Xeltec last lines if read as 95256 or 95320 is 7FF0 and 32Kb.
lwood
15th January, 2016, 07:09 PM
UPA's read just fine
Plcautoparts
17th January, 2016, 03:32 AM
I can read it with Xeltec Pro as 95256/95320/95640 all of this make Reading but dont know if correct number of Bytes, in Orange wich is the last line ? Xeltec last lines if read as 95256 or 95320 is 7FF0 and 32Kb.
orange last line is 1FFFF
alexs600
29th October, 2016, 06:12 PM
UPA's read just fine

I do not see 95m01 in list of devices

are you refer to 25lc1024
thanks
lwood
29th October, 2016, 06:35 PM
I do not see 95m01 in list of devices

are you refer to 25lc1024
thanks


in upa software go to Serial Flash SPI>M25P10. thats how you read and write
alexs600
29th October, 2016, 06:59 PM
OK thanks for info!!!
vard1972
5th September, 2017, 03:38 AM
on Upa list find a M25P10 3.3v it works tested