Please help me for 95910-3V200

[amir_82013]

Hello dear friends
i have a srs unit Hyundai that crash
95910-3V200 v1.1
anyone have help me how i can read data this mcu with xprog ?
(SAH-XC2361B-40F)
i need pin connection this board

Thanks
Best regards

[servicetecnocar]

I also am with this problem. however I have 2 ECU ok, and would like the pinouts to read with SMOK or XPROG. who can help please?

[servicetecnocar]

I managed to read this ecu, I need to clean this file.
I put a copied file from a good ecu, i program and not works. light on and configuration error, even similar with version and number .
i think clear the file original this is 95910-3v200 ver2.3

thankss


amir_82013 you need the picture?

[amir_82013]

Hello dear friends
i have a srs unit Hyundai that crash
95910-3V200 v1.1

[servicetecnocar]

can i help pleasee.?

i not solved

thankssss

[KACZANUK]

Hello dear friends
i have a srs unit Hyundai that crash
95910-3V200 v1.1
anyone have help me how i can read data this mcu with xprog ?
(SAH-XC2361B-40F)
i need pin connection this board

Thanks
Best regards
Hello Friend
U have the connections that you used to read this central with XPROG?

Thank you

[Porkam]

سلام دوست عزیز
تیم کوانتوم توانایی پاک کردن کدهای خطای این نوع مدول ایربگ را دارد لطفا به سایت زیر مراجعه فرمایید.


Hello my friend

Please refer to our website, we can clear crash data from Hyundai ACU 95910-3v200 v1.1 - v1.3 - v2.3 .

Regards
Porkam

[Johnner]

Porkam,couple of things here....

1. You need to introduce yourself first : Introduce Yourself
(http://www.digital-kaos.co.uk/forums/forumdisplay.php/2-Introduce-Yourself)
2. Then you need to have a look over these : Forum Rules




(http://www.digital-kaos.co.uk/forums/showthread.php/2-Forum-Rules)

[Johnner]

Take a look at #25 in there...


Oh......and welcome to Kaos..

[juancho18]

You will need:

CarProg (http://codecard.lt/carprog/carprog-universal-car-dashboard-immobilisers-airbag-and-car-electronic-repair-tool/prod_667.html) programmer with required software
A1 (http://www.codecard.lt/carprog/adapters/a1-carprog-odb2-adapter/prod_51.html) or A1 MULTI (http://www.codecard.lt/carprog/adapters/a1-multi-new-carprog-obdii-adapter-with-can-multiplexer-replaces-a1/prod_2334.html) adapter
C1 (http://codecard.lt/carprog/additional-carprog-adapters-not-included-in-any-carprog-full-packs-/c1-car-electronic-testing-on-table-adapter/prod_480.html) adapter


Reading procedure:

Connect CarProg to car by OBD using A1 (or A1 MULTI) and C1 adapters
Connect 500 Ohm resistor between CAN (yellow and green) wires.

Connection diagram for Kia and Hyundai modules with Infineon processors
http://codecard.lt/images/uploads/mac%20infineon/Connector1Water.png (http://codecard.lt/images/uploads/mac%20infineon/Connector1Water.png)
Connection diagram for Kia and Hyundai modules with MAC processors
http://codecard.lt/images/uploads/mac%20infineon/KIA_MAC_Wiring.jpg (http://codecard.lt/images/uploads/mac%20infineon/KIA_MAC_Wiring.jpg)
Connection diagram for Kia and Hyundai modules with MAC processors (for some modules you need to connect two GND wires)
http://codecard.lt/images/uploads/KIA_MAC_Wiring4.jpg (http://codecard.lt/images/uploads/KIA_MAC_Wiring4.jpg)


Follow same procedure as on car.