PDA

View Full Version : Solution control torque Mercedes Delphi



ernesto90
27th April, 2015, 08:42 PM
Disable continuous monitoring on the engine torque output (Torque Monitoring Management), usually associated with error or P061A P061B, allowing larger increments and without restriction during calibration of new maps.

you can know the solution free for all?
thanks:stung:

LaraVAG
27th April, 2015, 09:08 PM
there are some hidden limiters in Delphi CRD Sprinters ECU.

ernesto90
27th April, 2015, 09:16 PM
WE HAVE A solution to this file ?

ernesto90
27th April, 2015, 09:31 PM
Brand derivation of the file : MERCEDES
Model -derived file : B CLASS W246
Type derivation File : B180 CDI 1.8L 16V 80kW / 108HP CRD3.XX
Protocol derivation of file : FLASH_0366 MERCEDES DELPHI CRD3.X
Hardware Number : 6519040301
Software Number : 6519026400
Data Hardware:
Data Software :
Frame: WDD2462001N004997
Software version :
Replacement number : 6519010601
Engine Number :
Hardware Version :
Software update : 6519030707H

ernesto90
28th April, 2015, 01:08 PM
news? for me?

icezero2010
28th April, 2015, 04:10 PM
Disable continuous monitoring on the engine torque output (Torque Monitoring Management), usually associated with error or P061A P061B, allowing larger increments and without restriction during calibration of new maps.

you can know the solution free for all?
thanks:stung:


upload your mod and ori :-)
or better post your ols

or
Nm conversion make it stock

after torque limiter by pressure is two another torque limiter

and 1 single limiter :-)

ernesto90
28th April, 2015, 06:50 PM
[QUOTE = icezero2010; 2.518.189] caricare il mod e ori:-)
o meglio inviare i vostri oli o conversione Nm rendere magazzino dopo limitatore di coppia da pressione ? due un'altra limitatore di coppia e 1 singola limitatore: -) [/ QUOTE]

icezero2010
28th April, 2015, 06:59 PM
[QUOTE = icezero2010; 2.518.189] caricare il mod e ori:-)
o meglio inviare i vostri oli o conversione Nm rendere magazzino dopo limitatore di coppia da pressione ? due un'altra limitatore di coppia e 1 singola limitatore: -) [/ QUOTE]

english or german please this is not your full mod . send your file with the error

ernesto90
28th April, 2015, 07:04 PM
Already with this file by mistake

icezero2010
28th April, 2015, 07:23 PM
Already with this file by mistake

you have only chance I_C_FUEL_PULSE_O***ET_REF_APM

This map gives the pulse period o***et added to the the minimum pulse to give the required fuel quantity at the given Rail pressure.The map are indexed by each data indicated in the Y_Input definition, the main data being the first in the list.

and this is too much :-) you don?t need this map i have never chance.

blackwolf76
2nd May, 2015, 05:20 PM
upload your mod and ori :-)
or better post your ols

or
Nm conversion make it stock

after torque limiter by pressure is two another torque limiter

and 1 single limiter :-)

Hello,
I have the same problem on my c180, I copied all increments from a c220 that differences only on some maps and creates torque error. You may check please ??


https://www.sendspace.com/file/6idsck

Thanks in advance...

chip.tec
3rd June, 2015, 12:46 PM
Why cange only injection map? you got the axis right , but strange area to modify, no use under 1800 rpm