PDA

View Full Version : Kess V2 Harware Rework - FREE SOLUTION!



Pages : [1] 2 3 4 5 6 7 8

mbtun
28th April, 2015, 11:46 AM
Because some people are making some good money out of it let's make it free for everyone. Photo is of original board so check all others components to be as per this one.

http://s2.postimg.org/w00iwu9xh/original.jpg (http://postimg.org/image/w00iwu9xh/)

Thx will be nice.

Overtune
28th April, 2015, 02:32 PM
Hi, the words on the upper left side cannot be seen. Can you re-upload in better resolution or bigger letter font?
Thank you

Fantomisback
28th April, 2015, 02:44 PM
Hi, the words on the upper left side cannot be seen. Can you re-upload in better resolution or bigger letter font?
Thank you

when u click on image and open click again and u will see picture is very fine

mbtun
28th April, 2015, 07:51 PM
If photo is not clear enough ...
Transistors to use :
BCR112
MMUN2113
BC817

Murata filters:
NFE61PT472C1H9L (connect ground for all of them)

Capacitors:
1uF - 35V
220uF - 10V
10uF - 16V tantalum

Fill up all holes from side to side
Use photo as reference if others components are different

pulsar2000
28th April, 2015, 08:11 PM
maybe ,,, re word title, Hardware, sure its a TYPO,,,
good work thanks for the share,,,

zecas
28th April, 2015, 08:45 PM
Because some people are making some good money out of it let's make it free for everyone. Photo is of original board so check all others components to be as per this one.

http://s2.postimg.org/w00iwu9xh/original.jpg (http://postimg.org/image/w00iwu9xh/)

Thx will be nice.

now just put firmware and put this trolls out of bussiness

Prime
28th April, 2015, 08:49 PM
where find firmwre? I have 2 china clone KESS. Intresting tested

2xded
28th April, 2015, 09:56 PM
I asked about the resistor on the back side of the board, but the topic was closed. http://www.digital-kaos.co.uk/forums/showthread.php/320889-kess-v2-clone?p=2507342&viewfull=1#post2507342
Can anyone say purpose of this resistor?

mbtun
28th April, 2015, 10:36 PM
that resistor is not needed. in the original there is no resistor there.

2xded
29th April, 2015, 06:38 AM
For the original is not needed, but it was placed on the clone. Why?

vicius_the_one
29th April, 2015, 06:51 AM
that resistor is not needed. in the original there is no resistor there.
That's the mighty answer... :))

mbtun
29th April, 2015, 07:39 AM
Crying today mr Vicius? No more 50 euro for you now when the solution is free? No more bulls**it about every clone need different solution? Ktag rework solution will come soon.

mishu_b
29th April, 2015, 07:44 AM
For the original is not needed, but it was placed on the clone. Why?

that resistor is pull_up
if you will monitor where that one is connected than you will find out the purpose.

stay tune - more will came!

vicius_the_one
29th April, 2015, 08:20 AM
You are acting like kids.
You did nothing more than copy some masks and gather the info stolen from me.

mishu_b
29th April, 2015, 08:31 AM
You are acting like kids.
You did nothing more than copy some masks and gather the info stolen from me.

What? Are you kidding, right? Stolen - I do not understand you!
Could you please be so kind and explain with more words?

And we are not talking about resistor with tolerances 0.1% for a tool used into automotive - -little more than consumers area, it's not for "medical electronics".

All what is here is for education purpose - not for business! This is the "forum" meaning!

PremierD
29th April, 2015, 08:39 AM
Remember what happened to the last thread on this subject ? .......:)

betrescudan
29th April, 2015, 09:29 AM
please reply...maybe will finish this acts of revenge...

mbtun
29th April, 2015, 09:53 AM
The solution is free for everybody and was posted here to help other people. The photo is of original tool and is coming from another forum.
There is nothing stolen because Mr Vicius is not the developer of Kess V2 as he likes to think. What he did was to read the labels on the original transistors and replace them. Other people did the same with the same result.

If other forum coleagues have issues with their tools their are welcomed here and will be helped for FREE.

Mr Vicius as your clone is already fixed, we don't need spaming in this topic please!

zecas
29th April, 2015, 10:06 AM
You are acting like kids.
You did nothing more than copy some masks and gather the info stolen from me.

in this case you should make copyright branch lawsuit

betrescudan
29th April, 2015, 02:00 PM
mbtun-alias bazare...we all thanks for your sharing
but mate...is time to finish this war betwen you and v_t_o
here,and on the others forums is same shi+
be more creative and let the hate go on...you are both from same "motherland"...shame of you

OVERSPEED
29th April, 2015, 03:08 PM
Wich is the newest clone version (FW and Ksuite)?

What are the steps to upgrade ? (fix all wrong components and buy firmware and write on NXP with new card contents )

How it?s make tokens renew ?

Can it make new SIMOS from Golf TSI, Golf GTI and Jetta 211cv ?

If it can make, as the reading in Kess is virtual how it works ? (the person Wich sell the upgrade will provide the original files ?)

bartekbartek
29th April, 2015, 05:18 PM
How about ktag board? Possible solution like this?

ecutuners
29th April, 2015, 05:20 PM
Forget reset softwares etc, self reset Kess and Ktag is here :D unlimited resets anytime you like.

vicius_the_one
29th April, 2015, 05:56 PM
Ktag also yes can be reworked to work completely as genuine

OVERSPEED
29th April, 2015, 07:05 PM
Forget reset softwares etc, self reset Kess and Ktag is here :D unlimited resets anytime you like.

I send you 2 MP asking about Kess some days ago... do you mind sending one than I can answer and make some questions ?

How about my other questions ?

Kess 2.08/4.036 can make SIMOS 12 and 18?

ecutuners
29th April, 2015, 07:24 PM
I send you 2 MP asking about Kess some days ago... do you mind sending one than I can answer and make some questions ?

How about my other questions ?

Kess 2.08/4.036 can make SIMOS 12 and 18?

pm sent. No clone can do Simos because them protocols need fw5.00x

OVERSPEED
29th April, 2015, 07:35 PM
It?s only matter of time to clone FW 5.X ? or it will take some long time yet ?

betrescudan
29th April, 2015, 07:41 PM
ok mates...i offer free update online for kess fw 4.036....this shi+ must to finish...

mishu_b
29th April, 2015, 07:58 PM
................

bobolin4o
29th April, 2015, 08:01 PM
EDIT: Thanks for sharing!

EDIT 1: I have not suggested that, you wrong understand my words!

EDIT 2: And the pass is... :dontknow:

betrescudan
29th April, 2015, 08:08 PM
free 4.036 no password...

mishu_b
29th April, 2015, 08:20 PM
EDIT: Thanks for sharing!

EDIT 1: I have not suggested that, you wrong understand my words!

EDIT 2: And the pass is... :dontknow:

in PM please as you suggested

betrescudan
29th April, 2015, 08:31 PM
free 4.036 no password...
https://mega.co.nz/#fm/UIMFXA7I

dakapo2
29th April, 2015, 08:38 PM
free 4.036 no password...
https://mega.co.nz/#fm/UIMFXA7I
not working mate

zecas
29th April, 2015, 08:39 PM
4.036 without pass real working link
https://mega.co.nz/#!DsBgHA6C!IgwFbpXRc6zR9-3E5glbQJSDjdv5pkJ1vnQajRk_Ey0

if you break it no problem just buy new one

dakapo2
29th April, 2015, 08:41 PM
in PM please as you suggested

pm sent!!!!! thanks in advance

betrescudan
29th April, 2015, 08:42 PM
WAIT 15 MINUTES UNTIL FINISH UPLOAD TO MEGA...

bobolin4o
29th April, 2015, 08:43 PM
So... end of story! - https://mega.co.nz/#!DsBgHA6C!IgwFbpXRc6zR9-3E5glbQJSDjdv5pkJ1vnQajRk_Ey0
Thaks to all players!
:burnout:

betrescudan
29th April, 2015, 08:44 PM
AND IS SOMEONE who can share the real working update for ktag?

bobolin4o
29th April, 2015, 08:46 PM
AND IS SOMEONE who can share the real working update for ktag?

It will be nice...

betrescudan
29th April, 2015, 08:46 PM
4.036 without pass real working link
https://mega.co.nz/#!DsBgHA6C!IgwFbpXRc6zR9-3E5glbQJSDjdv5pkJ1vnQajRk_Ey0

if you break it no problem just buy new one
your 2.11 will kill nxp
is not a joke this mate...

betrescudan
29th April, 2015, 08:51 PM
upload complete...you can download now
https://mega.co.nz/#fm/UIMFXA7I

mbtun
29th April, 2015, 08:52 PM
NXP can't be locked for real. You can change CRP3 to CRP2 and after reflash.

zecas
29th April, 2015, 08:56 PM
yes it will explode
but dont worry be happy

Prime
29th April, 2015, 09:00 PM
upload complete...you can download now
https://mega.co.nz/#fm/UIMFXA7I
Bad Link
This link your accaunt

70max
29th April, 2015, 09:02 PM
http://www.digital-kaos.co.uk/forums/images/misc/quote_icon.png Originally Posted by betrescudan http://www.digital-kaos.co.uk/forums/images/buttons/viewpost-right.png (http://www.digital-kaos.co.uk/forums/showthread.php?p=2519074#post2519074)
AND IS SOMEONE who can share the real working update for ktag?




QUOTE=bobolin4o;2519075]It will be nice...[/QUOTE]

please
I seek even I

betrescudan
29th April, 2015, 09:12 PM
Bad Link
This link your accaunt
link is ok mate...your ISP limits your downloads

dakapo2
29th April, 2015, 09:14 PM
link not working also here

Music73
29th April, 2015, 09:16 PM
Me neither just getting mega page... Won't download...

70max
29th April, 2015, 09:16 PM
Link not Work well

betrescudan
29th April, 2015, 09:20 PM
mmm...shi+...i uploade the pack...but how can i create the link?

Prime
29th April, 2015, 09:25 PM
click on file right mouse button and select give link

betrescudan
29th April, 2015, 09:29 PM
ok solved
end of ...

bartekbartek
29th April, 2015, 09:37 PM
You have it for ktag?

betrescudan
29th April, 2015, 09:39 PM
You have it for ktag?
in developement...

betrescudan
29th April, 2015, 09:43 PM
this maybe will stop the chinese shi+ sales
or maybe will start another war ?

mishu_b
29th April, 2015, 09:45 PM
in developement...

nice - let's have share for all!

Tachodiag
29th April, 2015, 09:50 PM
In this way we will buy from china the programmers ready updated and reworked...no more extra job for us...
thnx guys for your work in the name of all resellers from Shenzen Valey !

kospoz
29th April, 2015, 10:11 PM
ok solved
new link
https://mega.co.nz/#!ZREzAYqR!UuaZOsMSNScZQXg87BW87zsDmk1LH0iVBHRsxdK s5os
Is there any guide for this update?I mean first step second......

ecutuners
29th April, 2015, 10:12 PM
Pitty that all who use it can't reset :D

betrescudan
29th April, 2015, 10:19 PM
Pitty that all who use it can't reset :D
hmm...do you think so?...there is reseter mate for this...not yours...your busines is finished...

betrescudan
29th April, 2015, 10:25 PM
Is there any guide for this update?I mean first step second......
yes...first step jlink - nxp write .bin
seccond step...no internet-kess on usb-extract rar with my program-start program from my folder
third step...take a coffee and wait families update
and last step...out sd card...format fat32.write my files from card rar ...insert into kess...make a donation and enjoy

USE AT OWN RISK...

ecutuners
29th April, 2015, 10:58 PM
So post the resetter for the people then :)

betrescudan
29th April, 2015, 11:18 PM
not yet...
maybe you will post yours reset button...
did you use for this reset, the nxp technology to conect to the ground?

ecutuners
30th April, 2015, 12:28 AM
not yet...
maybe you will post yours reset button...
did you use for this reset, the nxp technology to conect to the ground?

So you post update but no reset, what about the busy people who will do your update and be stuck to reset with locked NXP?
If you want to check how my reset button works then buy an device and copy my add on PCB ;)

mbtun
30th April, 2015, 05:38 AM
As I said before NXP is not locked in CRP3. You can downgrade to crp2 and after reflash with 4.036fw.

betrescudan
30th April, 2015, 06:19 AM
hmmm...another war?

mbtun
30th April, 2015, 06:58 AM
@ betrescudan - You can fight this one :)

betrescudan
30th April, 2015, 07:39 AM
i am too old for this mate...veteran of wars...i let the youngs to do this...:guns:

ecutuners
30th April, 2015, 07:40 AM
As I said before NXP is not locked in CRP3. You can downgrade to crp2 and after reflash with 4.036fw.
So your stupid too ? Crp3 cannot be downgraded you fool if it was possible people would be doing it to the NXP in original tools.
Anything else ?

betrescudan
30th April, 2015, 07:43 AM
I'll have a war I dont mind one especially little bitches like you.

you give update but no reset because you haven't got it fool u got 1 cfg

bitches like me ? can i ask a favor to moderators to bann you for this ?



Please respect each other and don't flame new members
If you have an issue with a member, PM a moderator or admin
Any racist, bigotry or discriminating posts will not be tolerated

ecutuners
30th April, 2015, 07:44 AM
bitches like me ? can i ask a favor to moderators to bann you for this ?

Ohhhh no I'm so worried :D

betrescudan
30th April, 2015, 07:53 AM
THANKS MATE FOR YOUR RESPECT AND ALSO FOR YOUR GOOD HELP OFFERED TO US...GOOD BYE

PremierD
30th April, 2015, 08:09 AM
Next .........................

ovi730
30th April, 2015, 08:34 AM
WARNING- the resset tool from the video pack will f...k your tools.
tokens are in fact the CFG file but is cripted and the resseter toll is just injecting it.
If somewone want to use token resseter i have repaked token file from the working pack. Thank you Dan for posting the solution.
Password for tokens tool is : SysAdmin

Junt make a token comparasion in hex or decript the token from that pack. you will se differences at the first lines. 2 possibilities :
1- fake cfg to destory as much tools as possible
2-cfg from another eu clone with different client no and activations

betrescudan
30th April, 2015, 08:44 AM
nice PM mate...

EcoTuningSolutions (http://www.digital-kaos.co.uk/forums/member.php/441312-EcoTuningSolutions)
http://www.digital-kaos.co.uk/forums/images/styles/DarkCore/statusicon_blue/user-online.png
Newbiehttp://www.digital-kaos.co.uk/forums/images/styles/DarkCore/reputation/reputation_green.gif
Join DateApr 2015Posts3Thanks0Thanked 0 Times in 0 PostsDownloads0Uploads0


NO PM'S TO BE POSTED

ovi730
30th April, 2015, 08:49 AM
Below please find 4.024 firmware. CFG needed

Possible the other cfg to be linked to this one. Hwo has a spare nxp can try

betrescudan
30th April, 2015, 08:49 AM
no problem mate...i said...i am veteran of wars...bye...and good luck

garagetech
30th April, 2015, 09:08 AM
Below please find 4.024 firmware. CFG needed

Possible the other cfg to be linked to this one. Hwo has a spare nxp can try

Hello ovi please empty you're pm its full

morgano
30th April, 2015, 10:22 AM
What has that 4.024 in special? Is older than 4.036

ovi730
30th April, 2015, 10:39 AM
As i said - is a 4.024 with crp3 disableled and full active all protocols. try it. i am out of changing nxp's - 16 nxp changed up to now :)

javyb
30th April, 2015, 10:39 AM
So after 30 uses you can't reflash nxp with the firmware again as it's crp 3

ovi730
30th April, 2015, 11:26 AM
No. Crp3 is direct from the begining. Just use the tool with the token provided. Come on are we tunners or........

ovi730
30th April, 2015, 11:52 AM
I was searching inside 4.024 - look adress 007c010 - client code and 000200 serial number are the same.
We have also 2 types of tokens = cripted cfg.
The ones from video pack that is different from the working one. Who will test an update from 4.024 to 4.036.
This firmware posted 4.024 it has all protocols active boats etc.

someone must try to flash 4.024 in nxp and that to use update pack but just use the other cfg.- renamed from "bad token decripted we have to test with 4024" to "K10033818.cfg"

betrescudan
30th April, 2015, 12:33 PM
i"m not finished all my tokens...but,i think is not need to reflash again the nxp...you don"t need to change the fw...i think you need to do again the same update from update folder with same cfg file...it will be rewrite the updates again...

ovi730
30th April, 2015, 12:45 PM
Hi Dan , indeed. I was asking to update from 4.024 to 4.036 not from 3.099 to 4.036
the firmware 4.024 havs all protocols activated.

MBTUN

please tell us the sequence of iap calls in order to cange the crp status and to be able to rerwite nxp.

ovi730
30th April, 2015, 01:21 PM
ups no one want to test it ??????????????????????is your turn coleagues. thats why we are a comunity . please test and report!!!!!!!!!!!

ovi730
30th April, 2015, 02:04 PM
Ok - one another thing to stimulate all of you.
Below KTAG FIRMWARE !!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Now start to comment on tnoter topic !!!!!!!!!! and please help for tests.

javyb
30th April, 2015, 02:08 PM
My question was after tokens expire can we reflash nxp with jlink or no

ovi730
30th April, 2015, 02:11 PM
:idea:no no no no nxp reflash. you have to resset them. i have created the tool with the correct token. or use initial update pack.
:heeeelllllooooo:
all of you wants only tested tosutions. you have to work my friends. it is free now but put your contribution here or shut the ............off

bartekbartek
30th April, 2015, 05:00 PM
Hmm, how test this ktag fw? Need jlink and write this file into nxp then start software or what? We can test for make good update solution for all.

I compare old fw 1,89 with yours and see smal change in adress 200h.

vicius_the_one
30th April, 2015, 10:48 PM
THIS ONE is usual 5.0 fw from china without customer number.......also try cu check content for next word....."fancu"...hint...x6220C


Ok - one another thing to stimulate all of you.
Below KTAG FIRMWARE !!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Now start to comment on tnoter topic !!!!!!!!!! and please help for tests.

betrescudan
30th April, 2015, 11:04 PM
do not play with ktag ...is not a ball...

8.23.motor
1st May, 2015, 12:22 PM
prejudice I tried your solution with fw fw 4,024 to 4,036 npx not locked after update obtained protocols active bike car dsg
how can I do to have full protocols ?I ask those of you who keep files for sd card for fw 4024 ?

mbtun
1st May, 2015, 04:04 PM
Nxp is not locked crp3 after update from 4.024 to 4.036? If this is true than we already have working solution ...

betrescudan
1st May, 2015, 04:55 PM
not yet...

8.23.motor
1st May, 2015, 05:48 PM
those of you who file sd card for fw 4024 ?:02.47-tranquillity:

betrescudan
1st May, 2015, 05:56 PM
if you have now 4.036...what for you need sdcard for 4.024 ?

mbtun
1st May, 2015, 06:57 PM
4.024 have trucks protocols active ... one of the most important reason I need kess. Otherwise there are very few new cars comparing to the other tools.

8.23.motor
1st May, 2015, 07:05 PM
fw 4024 has the right protocols activated for trucks serve this file sd card........the fw exists only missing files sd card if you have a solution

mbtun
1st May, 2015, 07:28 PM
@ 8.23.motor - you updated from 4.024 to 4.036 ... your NXP is locked or not? can you reflash now or not?

8.23.motor
1st May, 2015, 08:50 PM
npx not communicate more and even link j uart ( tx rx gdn )

ovi730
1st May, 2015, 09:11 PM
hello mate. what cfg did you ussed during update ?
post there the cfg from the pack that is posted. activation of protocols is linked in cfg file or device.fmw

8.23.motor
1st May, 2015, 09:18 PM
I used the config file posted in the solution betrescudan and fw 4024 skipe :cuozzo80

Overtune
2nd May, 2015, 03:09 PM
link is ok mate...your ISP limits your downloads
Your link points to my personal account at mega.co.nz
Where did you find this link and why are you sharing?

betrescudan
2nd May, 2015, 03:21 PM
Your link points to my personal account at mega.co.nz
Where did you find this link and why are you sharing?
sorry mate...if you click from your computer on this link,you will acces your account from mega....is a general link for all...if i click from my computer,will be my account...so,,,don"t worry,,nobody will access your account from here...

betrescudan
2nd May, 2015, 03:23 PM
https://mega.co.nz/#fm/UIMFXA7I
this link will not access your account...regards

javyb
3rd May, 2015, 10:01 PM
Can someone check this token rest and tell us if its anygood, I got of a friend

Overtune
3rd May, 2015, 10:36 PM
The file and rar are corrupt. Please try to re upload the proper version

vicius_the_one
4th May, 2015, 09:54 PM
GOOD FOR NOTHING....

betrescudan
4th May, 2015, 10:15 PM
is not corupted...is virus sallity...pfff

vicius_the_one
4th May, 2015, 10:18 PM
No that.... JUST NOT WORKING!!!

Kayhan 17#
17th May, 2015, 12:08 PM
Hey guys,

there are two black wires going to the left on the picture at the top left position (MM1 and RF), whats the purpose of this or should i just fill up the both holes?

also i have a single SMD Resistor on the back of the board with 1000 on it, is that the famous resistor of the clones?

Regards

mbtun
17th May, 2015, 12:54 PM
the black wire is grounding against electrostatic discharges. yes fill the holes. use my solution & photo, replace all transistors and remove the resistor on the back.

Kayhan 17#
17th May, 2015, 01:50 PM
mate, what kind of part is the "SP1", i dont have that on my board and there is no parts description =(

Regards

mbtun
17th May, 2015, 01:54 PM
photo ... i don't understand

Kayhan 17#
17th May, 2015, 02:01 PM
oh sorry =)
the red circle above ESMT Chip

mbtun
17th May, 2015, 02:15 PM
speaker piezzo = PKM17EPP (muRata manufacturer)

e.t.
18th May, 2015, 11:16 AM
Hi

Which parts solved the 24V problem?

mbtun
18th May, 2015, 11:40 AM
you tried your tool and is not working on 24V? after you replaced all components as per my photo and not working? I don't think so ...

e.t.
18th May, 2015, 11:46 AM
Hi

I changed nothing. I am only intressting for 24V problem

mbtun
18th May, 2015, 01:20 PM
You should change everything and test ... after this, you can come back and push the Thanks button.

elchip
19th May, 2015, 12:12 PM
You should change everything and test ... after this, you can come back and push the Thanks button.

Your solution is 100% OK tested .

mbtun
19th May, 2015, 06:28 PM
I know mate :) I just hate when people that don't try anything but still they are in doubt if free solution is good.

e.t.
20th May, 2015, 04:44 PM
You know for what is this resistor on the backside?

http://www.bilder-upload.eu/thumb/8eae72-1432137027.jpg (http://www.bilder-upload.eu/show.php?file=8eae72-1432137027.jpg)

cp2010
20th May, 2015, 05:16 PM
genuine pcb no have any components on the backside

ominimicu
20th May, 2015, 11:29 PM
You know for what is this resistor on the backside?

http://www.bilder-upload.eu/thumb/8eae72-1432137027.jpg (http://www.bilder-upload.eu/show.php?file=8eae72-1432137027.jpg)
Resistor is to fix micro boot erorr , using the tricore function!

mbtun
21st May, 2015, 05:15 AM
with replaced transistors as per my solution (genuine pcb), there is no need for any resistor on the back.

vicius_the_one
23rd May, 2015, 12:48 PM
You are so wrong....

ominimicu
23rd May, 2015, 01:26 PM
resistor is related to inner layer pcb circuits not component related

vicius_the_one
23rd May, 2015, 03:04 PM
Exactly. Not all boards have that issue

teamtuner
24th May, 2015, 01:21 PM
Exactly. Not all boards have that issue
i have this resistor...and with reworked pcb work well

vicius_the_one
24th May, 2015, 05:00 PM
Yes or no. Depending board's under layer issues...

thunder2
3rd June, 2015, 06:07 PM
Hi all
I did everything as it is in the Post and now my Kess is all gray.
Can help me please

Regards

morgano
3rd June, 2015, 06:32 PM
Hi all
I did everything as it is in the Post and now my Kess is all gray.
Can help me please

Regards

ugh! welcome to the NXP changers club.

teamtuner
3rd June, 2015, 09:33 PM
Hi all
I did everything as it is in the Post and now my Kess is all gray.
Can help me please

Regards
rewrite your sdcard
maybe will solve your problems

thunder2
4th June, 2015, 02:06 PM
Hi Teamtuner
Can you send me file to sdcard

Regards

teamtuner
4th June, 2015, 10:46 PM
Hi Teamtuner
Can you send me file to sdcard

Regards
what tool and for what fw ?

Evocati
5th June, 2015, 08:22 AM
I rework my kess, now i am planing to put on my kess speaker also, does anyome know which speaker must buy? mode?

TNX

garagetech
5th June, 2015, 08:24 AM
I rework my kess, now i am planing to put on my kess speaker also, does anyome know which speaker must buy? mode?

TNX

Hi what does this speaker do?

ominimicu
5th June, 2015, 11:27 AM
on dismposrt genius speaker does sound. ON orignal Kess i only heard it when doing ford Delphi mpc555 ECUS to put and remove key...nothing more...useles...

hcsaibot
5th June, 2015, 04:57 PM
I rework my kess, now i am planing to put on my kess speaker also, does anyome know which speaker must buy? mode?

TNX

speaker piezzo = PKM17EPP (muRata manufacturer)

viki300
8th June, 2015, 01:07 PM
how import is clock speed on MCU i did found some mcu cheap but it does have clock speed 3063 instead of that 4033 Hz so if i try those will it work

pulsar2000
10th June, 2015, 09:35 PM
Any one getting Bad Reads off kess ? as in all 0000 yet complete mb size, read a 2008 Audi edc17 today obd (not protected)
2mb file all 0000 Bad dump, i put car on charger while reading etc, ecu id all ok, and proceed to read, then realise bad read,
also sometimes i get checksum buffer error on write,,,,,
sw hw or my pc ?

Anyone, ? been told works better win 7 than xp,

Chippy0815
11th June, 2015, 07:17 PM
i think your soft is corrupt...try another ksuite!
And please only use v2.08 no higher versions!

pulsar2000
11th June, 2015, 09:29 PM
i think your soft is corrupt...try another ksuite!
And please only use v2.08 no higher versions!

i used good no reset sw, from a member on here,
doesnt install as such like original, just copy folder over, and click on k suite,
reads ok sometimes. others i get empty read,
annoying,
someone said use win 7 as could be runtime issue, i dunno ? any ideas

fronzethenight
12th June, 2015, 10:43 AM
Hi, i have an original kessV2 with last firmware installed but in Ksuite i have much family in grey! I have to pay actualizations to activate this family... Can update last version, like clone version?
Thanks

OVERSPEED
12th June, 2015, 02:32 PM
With these fix can KESS finally work with old Ford EECV EECVI ECU?s ?

2xded
12th June, 2015, 04:31 PM
Hi!
I have problem with my Kess V2 clone.
It is not connected to the boot mode with TriCore. Voltage appears several times on the red wire, only 2.6V. On the orange wire appears 12V.
Any tips are accepted.

pulsar2000
13th June, 2015, 02:04 PM
whats best operating system to use kess with ? i hear win 7 professional, then xp second, also i read
1.Q.During reading ECU data,get "checksum error".
A.Please research this software "visual C++ 2005 library" on google,download and install

Necessary ? you think c++ 2005 ?
i seem to get 2mb or 1mb or 512kb read, then when file looked at i have a bad read all 000000 and ffffffffffff
then sometimes on write checksum buffer error,

morgano
13th June, 2015, 09:14 PM
whats best operating system to use kess with ? i hear win 7 professional, then xp second, also i read
1.Q.During reading ECU data,get "checksum error".
A.Please research this software "visual C++ 2005 library" on google,download and install

Necessary ? you think c++ 2005 ?
i seem to get 2mb or 1mb or 512kb read, then when file looked at i have a bad read all 000000 and ffffffffffff
then sometimes on write checksum buffer error,


i would maybe resolder Kess RAM chip.

pulsar2000
13th June, 2015, 09:26 PM
i would maybe resolder Kess RAM chip.

you mean nxp ? never heard of ram chip, any idea were is on board Morgano,,, Thanks

gazvts
13th June, 2015, 09:42 PM
ESMT M12L2561616A

BubbaFet
13th June, 2015, 10:36 PM
Can someon _please_ write a quick'n'dirty howto on updating the firmware to 4.0xx ?

What is needed?
Is it updates by JLink, posted software?
What SW version can be used afterwards?

I'm getting _really_ confused with all this personal nick'nack. :/

pulsar2000
13th June, 2015, 11:27 PM
ESMT M12L2561616A

cheers Gaz, we spoke earlier, any ideas ? u know the score, real installer used, and now self reset, just want tool working,,,,your clued up any info

8.23.motor
14th June, 2015, 12:13 PM
have solution kess full protocol fw 4024 contact me


No ID posted please

yourmate
14th June, 2015, 02:11 PM
doesnt install as such like original, just copy folder over, and click on k suite

I've got some problem with understanding your post ;) but if you meant what I think you did then you do not do an "initial" install just copy over.
I don't know if your reading inconsistencies are related to sw or hw but to make the software part sorted out is a tad bit easier so I'd start with that...

Try this:
- get rid of everything KSuite related from the PC/laptop
- install "original installer" from link (https://mega.nz/#F!WF8F3AiZ!xPCc-KE5bwxOgb3WjO6jNg)
- THEN copy KSuite v2.8 folder from same link
- test...


ps. Have you seen my PM?


EDIT:
It even works on a Win 7 VM running on a Win 7 x64 Ultimate system

yourmate
14th June, 2015, 02:20 PM
Can someon _please_ write a quick'n'dirty howto on updating the firmware to 4.0xx ?


Download the stuff from here (https://mega.nz/#F!WF8F3AiZ!xPCc-KE5bwxOgb3WjO6jNg) the write up is in the "HOWTO and other stuff"
I just repacked the stuff and rewrite the "manual" a bit which was posted by gazvts originally.

Strictly NO PASSWORD ;)

beltronics
14th June, 2015, 02:47 PM
whats best operating system to use kess with ? i hear win 7 professional, then xp second, also i read
1.Q.During reading ECU data,get "checksum error".
A.Please research this software "visual C++ 2005 library" on google,download and install

Necessary ? you think c++ 2005 ?
i seem to get 2mb or 1mb or 512kb read, then when file looked at i have a bad read all 000000 and ffffffffffff
then sometimes on write checksum buffer error,


That error came to me yesterday to me, edc17c46 vag.
Used windows 7 Professional 64bit, change to windows xp professional and solved.


regards

Chippy0815
14th June, 2015, 02:50 PM
@yourmate
mate but your manual isn't correct...the one from gazvts is better, even it is for you hard to understand....
the parts you describe are not wrong in the way to say it won't work in this way...but they are unneeded.

yourmate
14th June, 2015, 02:56 PM
what do you mean?

Chippy0815
14th June, 2015, 03:05 PM
for kess just as simple:
flash fw
write new files to sdcard
push update files to update folder
update
finish
enjoy

BubbaFet
14th June, 2015, 04:01 PM
for kess just as simple:
flash fw


How do we flash the fw? With jlink?

Chippy0815
14th June, 2015, 04:45 PM
you can flash by whatever you want.

ISP, serial

pulsar2000
14th June, 2015, 06:13 PM
I've got some problem with understanding your post ;) but if you meant what I think you did then you do not do an "initial" install just copy over.
I don't know if your reading inconsistencies are related to sw or hw but to make the software part sorted out is a tad bit easier so I'd start with that...

Try this:
- get rid of everything KSuite related from the PC/laptop
- install "original installer" from link (https://mega.nz/#F!WF8F3AiZ!xPCc-KE5bwxOgb3WjO6jNg)
- THEN copy KSuite v2.8 folder from same link
- test...


ps. Have you seen my PM?


EDIT:
It even works on a Win 7 VM running on a Win 7 x64 Ultimate system


Not so simple using dannys edited sw, self reset, as my tool has self reset button, so have to use his sw, will try another laptop, see if get better reads

BubbaFet
14th June, 2015, 06:26 PM
you can flash by whatever you want.

ISP, serial


OK, I have never replaced the NXP (never done a single write yet) on my clone - will the original NXP be able to be updated, or do I need to buy a new NXP first?

carmageddon
14th June, 2015, 07:09 PM
try to connect with jlink, if you connect with success at the cpu you can read-write without problem, if you cannot you need to change cpu

BubbaFet
14th June, 2015, 07:59 PM
Cheers, I'll get the solderingstation out then. Are the HW modifications strictly needed along the FW/SW updates? Or can I order the parts and the use it until I get the parts needed for the HW modifications

toms4
14th June, 2015, 08:37 PM
Cheers, I'll get the solderingstation out then. Are the HW modifications strictly needed along the FW/SW updates? Or can I order the parts and the use it until I get the parts needed for the HW modifications

You can update FW without HW modifications.

BubbaFet
14th June, 2015, 09:25 PM
It seems I could update via JTag. :) Now trying the net steps..

BubbaFet
14th June, 2015, 10:45 PM
Argh Bollocks. :)

Disabled the WIFI/Ethernet
Updated the FW
Updated the SD
Installed 2.08 - removed contents
Copied the contents of the 2.08 folder
Copied the update folder
Starting KSuite

Then BANG - "External Exception EEFFACE" :/

When plugging in the Kessv2 (USB->Computer) the red LED just blinks once every second - this cannot be normal?

javyb
14th June, 2015, 10:46 PM
Argh Bollocks. :)

Disabled the WIFI/Ethernet
Updated the FW
Updated the SD
Installed 2.08 - removed contents
Copied the contents of the 2.08 folder
Copied the update folder
Starting KSuite

Then BANG - EEFFace error. :/

When plugging in the Kessv2 (USB->Computer) the red LED just blinks once every second - this cannot be normal?
The firmware it gets stuck on when updating if u remove from folder the update will continue

morgano
15th June, 2015, 12:13 AM
Led blinking on connecting to usb is bad business.

Dolcevita
15th June, 2015, 03:06 AM
I've got some problem with understanding your post ;) but if you meant what I think you did then you do not do an "initial" install just copy over.
I don't know if your reading inconsistencies are related to sw or hw but to make the software part sorted out is a tad bit easier so I'd start with that...

Try this:
- get rid of everything KSuite related from the PC/laptop
- install "original installer" from link (https://mega.nz/#F!WF8F3AiZ!xPCc-KE5bwxOgb3WjO6jNg)
- THEN copy KSuite v2.8 folder from same link
- test...


ps. Have you seen my PM?


EDIT:
It even works on a Win 7 VM running on a Win 7 x64 Ultimate system

Thx mate for Sharing got few questions.
for what is KessV2_4.036_SDCARD_before_final_format.rar ? it?s insde HOWTO and other bits.rar .
If i follow step by step your how to above mentioned rar folder is useless or not?
Is there a Token limitation ? if yes how to reset?


knd regards

BubbaFet
15th June, 2015, 07:26 AM
Ok, I flashed the old firmware back to the Kess. Same issue - blinking LED and EEFFace error. Then I tried to keep the JTag connected and the JLink connected via USB to the computer - now it works. :/

Kess Suite did it's update and everything seems fine. The About tells me that I have 4.039 FW and 2.08 SW. If I disconnect the JTAG I get blinking LED again - reconnect it and everything is fine.

I do not have a car connected to the KESS - I wonder why it is not able to boot properly without the extra power from the JTAG?

..Next step, try it on the car.


EDIT: All protocols are greyed out - I can browse them, but I cannot connect using any of them. SDcard issues?

BubbaFet
15th June, 2015, 09:44 AM
OK, it seems the 4.39 Firmware posted earlier in this thread is CRP3 protected despite stated otherwise. That means no JTAG access anymore. However.. Judging by this pdf: http://www.nxp.com/documents/application_note/AN10851.pdf

it should be possible to enter CRP2. This must be what the Kess Suite does when it updates. We "just" need to find out how to enter the CRP2 - then we can wipe and flash with a non-CRP3 firmware again. (4.024 is that CRP3?)

If there is an update folder in the KessSuite folder - then Kess Suite starts updating the firmware, but is it the NXP firmware it alters?

In the info dialog of KessSuite I have the following:

Device Type: M
FW version: 4.036
Serial Number: K666....
Customer Code:
Group Code:
Subscription Expiry Date:

heteromies
15th June, 2015, 09:50 AM
OK, it seems the 4.39 Firmware posted earlier in this thread is CRP3 protected despite stated otherwise. That means no JTAG access anymore. However.. Judging by this pdf: http://www.nxp.com/documents/application_note/AN10851.pdf

it should be possible to enter CRP2. This must be what the Kess Suite does when it updates. We "just" need to find out how to enter the CRP2 - then we can wipe and flash with a non-CRP3 firmware again. (4.024 is that CRP3?)

If there is an update folder in the KessSuite folder - then Kess Suite starts updating the firmware, but is it the NXP firmware it alters?

In the info dialog of KessSuite I have the following:

Device Type: M
FW version: 4.036
Serial Number: K666....
Customer Code:
Group Code:
Subscription Expiry Date:

If fw is 4.036 you cannot use jlink anymore, MCU is locked CRP3. Try to play with files now... If doesnt work, need replace MCU and start over.

What i have hear, 4.026 is CRP2, and its older fw, so some OBD- protocols missing vs 4.036

ecutuners
15th June, 2015, 10:19 AM
With serial k6666666 and 4.036 it's time for new mcu

BubbaFet
15th June, 2015, 10:35 AM
I thought so. :/

teerak2uk
15th June, 2015, 01:21 PM
New nxp about ?20 on ebay or ?5 on aliexpress

Dolcevita
15th June, 2015, 02:27 PM
I got serial K6xxxxx35 will be mine locked if i update it ?

gazvts
15th June, 2015, 03:01 PM
It will only f*#k the nxp if you update it wrong

BubbaFet
15th June, 2015, 05:14 PM
It will only f*#k the nxp if you update it wrong

Uhm no. If you update it with a crp3 enabled, you will not be able to read not write it again.

Chippy0815
15th June, 2015, 06:42 PM
This is the way every update work!

ecutuners
15th June, 2015, 07:37 PM
Updates done by ksuite are locked automatically.

BubbaFet
15th June, 2015, 07:41 PM
so if i did not copy the update folder over - I would have had a working Kess?

..This is exactly why somebody needs to make a tutorial - there are far to many opinions and misconceptions floating around. :/

Chippy0815
15th June, 2015, 09:10 PM
this why there are people that can do the update for you!

Some say it is only about the money.....but the updates arn't expansive and are safe...

but if you try at your ow, every time a risk to make a mistake and block your tool!

masciaro
16th June, 2015, 01:45 AM
I have this error. Can anyone help me?

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=318282&stc=1

toms4
16th June, 2015, 02:05 AM
so if i did not copy the update folder over - I would have had a working Kess?

..This is exactly why somebody needs to make a tutorial - there are far to many opinions and misconceptions floating around. :/
How you then get updated FW to 4.036, if you do not use update folder!?

hcsaibot
16th June, 2015, 07:37 AM
Update is only possible if FW is lower as FW 4.036

BTW:
OBD2buy.com has stolen ECU-Tuners Token reset Solution, with 99 Token Files.
Is this 99 Token or 99 x 30 Tokens?
http://www.obd2buy.com/file/KESS_V2_FW4.036_TOKEN_RESETTER_SOFTWARE.rar
(The files are in ksuit temp folder)
There are also some protocol updates?! Did anyone know if this will work?

edit:
Every of this 99 tok files have the same MD5, this mean that every token file have the same content... --> only one Reset is possible??

ecutuners
16th June, 2015, 09:50 AM
Update is only possible if FW is lower as FW 4.036

BTW:
OBD2buy.com has stolen ECU-Tuners Token reset Solution, with 99 Token Files.
Is this 99 Token or 99 x 30 Tokens?
http://www.obd2buy.com/file/KESS_V2_FW4.036_TOKEN_RESETTER_SOFTWARE.rar
(The files are in ksuit temp folder)
There are also some protocol updates?! Did anyone know if this will work?

edit:
Every of this 99 tok files have the same MD5, this mean that every token file have the same content... --> only one Reset is possible??

Yes you are correct it is same token copied 99 times and is a scam

hcsaibot
16th June, 2015, 09:55 AM
Work this one reset?
And what should the protocoll update aim?

Chippy0815
16th June, 2015, 04:59 PM
It's all fake mate, like all the time!

hcsaibot
16th June, 2015, 05:05 PM
hehe yes mate check this log file from sd card :rofl:




Info file for log: ver 1.000


Time: 23/02/2014 03:58.43

VoltStart: 13.61

Device SN: 66666666
GOS ver: 3.099
ManagerCode: D6666
ClientCode: D6666

Procedure: ECU Identification
Brand:
Model:
Type:
Protocol: FLASH_0310 BOSCH TRICORE MEDC17 BOOTLOADER
ver: 3.004

Filename:
FileOpt:
FileMd5:

Result: ERROR
ErrorCode: 3B0B
ErrorDescr: MICRO Wakeup error

VoltEnd: 13.61


Info file for log: ver 1.000


Time: 29/11/2012 13:22.52

VoltStart: 11.87

Device SN: 12041102
GOS ver: 3.099
ManagerCode: C3553
ClientCode: C3553

Procedure: ECU Identification
Brand:
Model:
Type:
Protocol: FLASH_0313 BOSCH TRICORE MEDC17 BOOTLOADER TPROT8/10 - VAG
ver: 1.029

Filename:
FileOpt:
FileMd5:

Result: ERROR
ErrorCode: 3000
ErrorDescr: Wake up error

VoltEnd: 11.87

ecutuners
16th June, 2015, 06:40 PM
Yes it is the original details of the tool China cloned

Chippy0815
17th June, 2015, 05:57 AM
Work this one reset?
And what should the protocoll update aim?

Yes this one reset work, but I think not for his customer, because chinese have stolen the solution from ecutuner, so I guess every chinese use his solution for activation.
So if you have already used the token for activation you can't use them for reset....

So he supports his customer a stolen solution with non working resets. You can try to reset, you won't block your nxp. If your tool was already activated the only thing what will happen, is exactly, nothing, and this is what already a costumer poster. Tried to reset, but don't work.

Dolcevita
17th June, 2015, 02:47 PM
Next Question should i buy Kess v2 with reset button and rework this one ?

morgano
17th June, 2015, 03:02 PM
Next Question should i buy Kess v2 with reset button and rework this one ?

It depends which Kess with reset button you buy. Chinesse for sure, Danny's already reworked before fit reset button. ;)

Dolcevita
17th June, 2015, 05:55 PM
Were can i buy it ?

Chippy0815
17th June, 2015, 06:00 PM
Have a look at post #195

cawadany
18th June, 2015, 05:02 PM
Where can we buy the components for the rework?

vicius_the_one
18th June, 2015, 08:48 PM
Looks like resetting is still on development for many many many people. My solution is final reset solution. No need any token limit... Works ever forever and ever forever. ;)
No need any hw mod like button solution...

moky
18th June, 2015, 08:56 PM
when you have good dealer or friends ,reset token is really easy now ..but of course token no limit is better :D

vicius_the_one
18th June, 2015, 08:59 PM
Available for every tool.. Kess with/without truck or ktag...

teamtuner
18th June, 2015, 09:22 PM
mmm...perpetuum mobile it not exist...and i like the limits...because i can pass outside ...to the next limit

vicius_the_one
18th June, 2015, 09:23 PM
Not in this case... Trust me ;)

teamtuner
18th June, 2015, 09:31 PM
i want to buy EU clone with remote controll or vocal command...is there anyone who is able to do this?...or who can create a win programm for use thoses clones with vocal commands?....without butons,or other shi+s?....mmm...i am thinking....:roflmao::roflmao:

Chippy0815
18th June, 2015, 11:13 PM
I'm very interested of vicious solution to update fw 4.036 to v5 ;)

vicius_the_one
19th June, 2015, 04:57 AM
Who said 5.0

vicius_the_one
19th June, 2015, 09:55 AM
i want to buy EU clone with remote controll or vocal command...is there anyone who is able to do this?...or who can create a win programm for use thoses clones with vocal commands?....without butons,or other shi+s?....mmm...i am thinking....:roflmao::roflmao:

you should reconsider your behaviour :)

BubbaFet
24th June, 2015, 06:20 PM
319597

Does anybody know if the 4.024 Firmware is CRP3 or CRP2? Also can someone verify the 4.024 Firmware attached here - is it safe to flash it via jTag ?

cp2010
24th June, 2015, 06:53 PM
no crp, firmware 4.024

zecas
24th June, 2015, 10:08 PM
hello
what update folder to use fore firmware 4.024?

regards
z

teamtuner
25th June, 2015, 12:26 AM
no need update folder...need other things

2xded
25th June, 2015, 05:26 AM
"... other things" - is this money? :apologetic:

zecas
25th June, 2015, 05:02 PM
dont no why i even bother to ask
must convince my self that DK is now 100% comercial forum

morgano
25th June, 2015, 05:35 PM
When you ask for commercial solutions is natural you get in return commercial answers ;)


Regards,

zecas
25th June, 2015, 06:15 PM
didn?t know it was a comercial question put that in rules then

stupedity sometimes knows no limits

teamtuner
25th June, 2015, 07:29 PM
"... other things" - is this money? :apologetic:
no mate...is not about monney...is about how to use your brain.exe...for free
or maybe you can read the post of cp2010...no crp...like 3.099...so,use your brain...or better...use j-link...and a 2 GB sdcard

Kayhan 17#
25th June, 2015, 07:48 PM
So are we going to write some tutorial or do some guys still have to painfully kill their devices?

teamtuner
25th June, 2015, 09:13 PM
upsss...from october 2010 untill now only 12 posts...and now,after 5 years you founded DK with maybe something free for eat....

BubbaFet
26th June, 2015, 08:59 AM
So are we going to write some tutorial or do some guys still have to painfully kill their devices?

This is exactly what I asked for a few pages back. But DK is no longer a forum where you strive to help eachother - it is now a forum where people are bitching and telling others that their solutions are crap.

I'm still trying to get my Kess clone to work properly, but it is extremely difficult to navigate the information in the forum as there is _SO_ much bull~~~~. :)

What I did find out - from the tutorial posted a few pages back is that you DO NOT want KSuite to update the firmware for you, it WILL kill your interface. Only way forward is (I think) to flash a correct firmware by jTag. As far I know you cannot flash a 4.036 firmware via JTag and get a working clone. I *hope* that I'm able to flash the 4.024 firmware via JTag and still have a working Kess.

teamtuner
26th June, 2015, 09:48 AM
mate...you can reflash your nxp with j-link only one time with 4.036...and work ok...but after that,you need tokens for reset...can"t use seccond time j-link...crp protection activated
is not like 3.099 or 4.024

teerak2uk
26th June, 2015, 12:35 PM
mate...you can reflash your nxp with j-link only one time with 4.036...and work ok...but after that,you need tokens for reset...can"t use seccond time j-link...crp protection activated
is not like 3.099 or 4.024
So maybe better to go with 4.024

Chippy0815
26th June, 2015, 12:56 PM
Wuhuuu many wrong intentions.....
If you HAVE 4036.bin you can flash as often you like, but there are only a few people who have....

Most of you think they will flash 4036 fw but on fact it is 3099

Cheers

teamtuner
26th June, 2015, 01:00 PM
yes...right point chippy...i founded gents that said ."after reflash with 4.036 i can reflash again"....pfff...fake fw 3.099 made in china guys...with only the name changed on hex...ufff

Chippy0815
26th June, 2015, 02:05 PM
LIKE I said, at this time there are only a couple person who have real 4036 bin
Even I don't have it!

motorsportsz
28th June, 2015, 11:51 PM
Anyone have a link to a Kess eu or original case housing or enclosure?

Chippy0815
29th June, 2015, 07:21 AM
I have, but why you need?

motorsportsz
29th June, 2015, 07:58 AM
I have, but why you need?

Can you pm me the link please? Because my case has taken a beating

janake
29th June, 2015, 10:39 AM
Wich is the newest clone version (FW and Ksuite)?


What are the steps to upgrade ? (fix all wrong components and buy firmware and write on NXP with new card contents )

How it?s make tokens renew ?

Can it make new SIMOS from Golf TSI, Golf GTI and Jetta 211cv ?

If it can make, as the reading in Kess is virtual how it works ? (the person Wich sell the upgrade will provide the original files ?)


Latest version for both software and firmware
Software: V2.13, firmware: V4.036

teamtuner
29th June, 2015, 06:16 PM
[QUOTE=janake;2551550][U]


Latest version for both software and firmware
Software: V2.13, firmware: V4.036

you also want to sale shi+ ?
what means 2.13 for a firmware created for 2.08?
mate...if you want to sale something...do it with true versions...china version shi+ not interesting

moky
29th June, 2015, 07:19 PM
This thread turn around because all is now maitrised with last kess 2.08 ......only deal is now the "ghost" subject...

same history since 15 years for all clones !!!! :D


so future clone is????? :D

atomiczen
30th June, 2015, 11:58 PM
i have a strange issue with a 2.12 kess v2 fw 4.036 reworked
it worked fine for a month, now when i start ksuite 2.12 program start and buttons are grey, i close program and start ksuite 1.93 and button worked
i connect another clone fw 4.036 and it work well also with 2.12 so problem not in software
what happened? if nxp is locked it don't work on any software right?

Chippy0815
1st July, 2015, 10:18 AM
You can leave me your pass and id for team viewer. I can help you out in any case!

atomiczen
2nd July, 2015, 10:24 AM
You can leave me your pass and id for team viewer. I can help you out in any case!
thanks
now i working on this issue and i'm testing some solution
there's only 4 token available on this tool, but no token reset software succesfully renew them
it work with all software from 1.89 to 2.07, and grey button from 2.08 to 2.12
tested both 009 and 011 usb driver

Chippy0815
2nd July, 2015, 05:22 PM
Like i told you if you need help just contact me

fronzethenight
3rd July, 2015, 11:37 AM
Hi, i have an original kessV2 with last firmware installed but in Ksuite i have much family in grey! I have to pay actualizations to activate this family... Can update last version, like clone version?
anyone made this?

Thanks

vicius_the_one
3rd July, 2015, 11:42 AM
Replace nxp and everything is possible then

fronzethenight
3rd July, 2015, 01:24 PM
but nxp have last firmware update... where are saved active family in kess?

thanks

vicius_the_one
3rd July, 2015, 01:36 PM
Alientech is last to help you with actual nxp..... With a substantial subscription payment

majsterx
8th July, 2015, 11:54 AM
@fronzethenight (http://www.digital-kaos.co.uk/forums/member.php/73757-fronzethenight)
De-solder your NXP, replace card. Put new one, program and work illegally ;)
But will be hard get more active protocol, or maybe did u have slave tool with only car, then sure any clone upgrade available protocols, no other smart way to doing that ;)
I think they work now for more advanced protect, any way long time they product not cracked;)

catala20032004
11th July, 2015, 05:03 AM
Vicius_the_one please clear your pm

raben785
14th July, 2015, 12:37 PM
To test the firmware files 4,024 that must be entered in the sd card? and soft 2.06..2.08 ....?
Thank You

Chippy0815
14th July, 2015, 02:52 PM
For fw 4024 use ksuite v2.07

budG60
16th July, 2015, 11:02 PM
Can anyone post a working link to downolad a kess 4.036 token resetter?

teamtuner
17th July, 2015, 07:05 AM
the reseter need to be for your fw client code and serial...and i don"t think that you will find for free

Chippy0815
17th July, 2015, 09:39 AM
There is no reseter for free, but if you need you can contact me by pm

vicius_the_one
17th July, 2015, 09:39 AM
Bud... I will reset free

teamtuner
17th July, 2015, 11:21 AM
yes...nice idea...and maybe the others will post for free all that have into personals computers...all sollutions:burnout: