HELP W203 ECU SIEMENS AM29F400BB TO VIRGINIZE

[yssf]

Hi Guys,
help please to make virgin this ecu.
i tried ff from 4000 to 8fff not work

thanks,
guys

[dikseln]

Use ABR and after star diagnose for initialize it. Attention, is important to have the throtle in good condition because need to learn it

[yssf]

I know i must use star.
Any help to make this dump Virgin.
Siemens ecu 4se.

[MVVL]

Hello. Like the rules correctly. 313183

[Hanukkah]

Post eis data and I will give you a file synced to eis.

[yssf]

Thanks MVVL&Hanukkah,
Mvvl i have made this virgin dump before,stated in my 1st post but always get this fault during coding .RESPONSE OF XENTRY FRAMEWORK CAN'T CONNECT TO SOCKET LISTENER.
Thaught was wrong dump,but read some where that is possible to remove xentry framework to complete coding.

Does someone know how to remove it?
Note:I'm using Chinese Star, tried throught xentry&das without success,

Hanukka my Etl programmer got damage,still waiting for the new one,which I always use to securely read the mcu,I tried with xprogm without success,error:vcc pin overloaded.
Have you ever read it with xprogm?
I have also orange5 but not sure if can read it securely.

Any help please!

[yssf]

here is the eis dump thanks for your time

[Hanukkah]

Here is your SIM4 LE ecu dump synced to EIS.

[Hanukkah]

Thanks MVVL&Hanukkah,
Mvvl i have made this virgin dump before,stated in my 1st post but always get this fault during coding .RESPONSE OF XENTRY FRAMEWORK CAN'T CONNECT TO SOCKET LISTENER.
Thaught was wrong dump,but read some where that is possible to remove xentry framework to complete coding.

Does someone know how to remove it?
Note:I'm using Chinese Star, tried throught xentry&das without success,

Hanukka my Etl programmer got damage,still waiting for the new one,which I always use to securely read the mcu,I tried with xprogm without success,error:vcc pin overloaded.
Have you ever read it with xprogm?
I have also orange5 but not sure if can read it securely.

Any help please!

Xprog not read 908 properly. You can use other programmers. R270 better for in circuit in these MCUs

[yssf]

Thanks mate I'll try n report

[yssf]

hanukkah i mistakenly damage the mcu so i could not be able to test your dump,i order for another ezs maybe you could help again for a new dump when i get the ezs
thanks

[Mario3]

Sorry to hijack thread but i need also help with a similar situation, HANUKKAH can you make me a snyced file also ? but car is w210 200K SIM4 LE ecu, i can post EIS data tomorrow ?

This car is driveing me crazy, cant snyc the ECU with star. I get 8.600 error and similar no matter what flash i use

regards

[Mario3]

Here are the esl and eis dumps readed with ak500, ori flash of the ecu is corrupted, i uploaded also 2 flash files from same ecu number that i found here but one is from a w203

So please if you can repair my ecu flash or pair one that will work. I really need help with this

car is:

w210 200K y2002 AT transmission

ecu data:

10111540872

A 111 153 18 79
HW 44/00
FD 16W01
Q 01

Siemens
5WK9 0403 (1)

SIM4 LE

1154 0870


314119

314120

314121


thanks up front

regards

Mario

[MVVL]

Mario , test. 314219

[Mario3]

Mario , test. 314219
Thanks mate, i will try in the morning. Can you send me the pass to the files ? i cant send you a pm your box is full

regards

[MVVL]

Mario3 pass PM.

[Hanukkah]

@ Mario

I don't know how corrupted your ecu files are but I just synced them all to the EIS data you sent...

[Mario3]

Unfortunatly it does not work, i tried the flash from MVVL and the one hanukkah synced from an w210. The one from w203 i didint even try since it has different ezs so it wont work anyway.

When i turn on the ignition the fan turns on... Diag works and in the parameters of the ecu in drive autorisation is everwhere NO and no serial number

:(

[MVVL]

What dumps have you tried? I gave you a kit and test a program log which shows that the synchronization is. We see wine code in the ECU. It does not work? What's the problem with the car?

[Mario3]

I tried your dump for the ecu, the other dumps where not changed so only ecu i modified...

And hanukkahs from ozher ecu but synced to my eis.

Both behave the same. Fan turns on right after ignition, problem is that the car wont crank

[MVVL]

Vehicle production?

[Mario3]

W210
Y: 2002
200 Kompressor

[MVVL]

Engine starts?

[Mario3]

No cranking, that is the main issue.

When you check everything with diagnosis, all is fine except in live values from ecu in DRIVE AUTHORISATION everything is set to NO and ther serial number is 000000000

Does Our file have to be adapted with star diag ?

[MVVL]

Adapting star diag is not necessary, the program I use, makes synchronization ECU. Let's try to get a dump of the ECU recalculate key, eis..... Key Type 021 ....?

[Mario3]

I just plugged in another ecu from a scrapyard but with different number

This one is A111 153 17 79

When plugged in fan doesent start, and in diag are some errors regarding can comunication with ezs so i think this one is form an w203

In drive authorisation i can see finally a serial number and all other things are marked YES except the last one which is normal in this situation.

So seen from here the ecu is the problem... but if i open this ecu and you sync this flash again on my eis it should start right ?

Thanks

[MVVL]

Damp ECU ?

[Mario3]

If i open it i cant return it to the scrapyard. I have to be 100% sure that it will work

[MVVL]

What other options are there? You say that your ECU is defective?

[Mario3]

I say that my ecu behaves crazy, that the flash is ok and plugged in the fan trnes on and i cant see any drive authorisation functions.

The ecu from scrapyard works fine but i just want to be sure that it is compatible with the car so i dont have to pay it and search for another.. i am pretty sure that it will start when synced but im scared that other things wont work on the car

[MVVL]

Your ECU diagnosed adequately shows the parameters? Read again from your ECU flash and place it here that you have read and what was covered.

[Mario3]

I called Benz and searched for compatible numbers on the ecus that can be fitted to this car

Old one was
A 111 153 18 79

Newer compatible ones are:

A 111 153 26 79
A 111 153 30 79
A 111 153 35 79

And good news is i found an ecu with ...26 79 number and i will get it in 1 or 2 days. When i get it i will post flash for new sync

Regards

[Mario3]

315862


Can someone please sync this dumps for me so it start without adaptation with star diag

[MVVL]

Why dump * 5Р08 *? Dumps esl test does not pass.

[Mario3]

5p08 is from ecu, cdi2 engine. Ecu and esl are from same car. Eis is from another but has paired working key. I tried to erase both eeproms in esl and renewed it with ak500 and put together works. But with diag in eis status of cpu2 in esl is locked. I tried to make autosync in ecu but didnt start the car and found that licked mcu2 in esl. But virgin dump inside