PDA

View Full Version : BMW 318 D edc16c35 chiptuning



kenancatli
15th June, 2015, 09:49 PM
hello
help please
BMW 318 D edc16c35 chiptuning bosch 0281 012880
I read with galletto V2 euroclone via OBD not problem
I write a gain tuned file error via OBD not connect with ecu help please
I try

I try with now bdm not connect with ecu

ecu killed?

what I can do?

regards

dean 21
15th June, 2015, 10:13 PM
Hi, did your bdm recognizes ecu ??

kenancatli
15th June, 2015, 10:32 PM
bdm 100 and fgtech euro clone same pinout?
not connect with bdm

dean 21
15th June, 2015, 10:52 PM
pinout is the same, exept there is some china clone bdm100 that have reversed pinout.
test where is gnd

dean 21
15th June, 2015, 10:55 PM
better use g2 for bdm if not sure.

kenancatli
15th June, 2015, 11:05 PM
I try with BDM gal2 come this fault pic?

regards

kenancatli
15th June, 2015, 11:16 PM
bdm no recognizes ecu !!!
maybe bdm no good connect?
regards

kire106ka
16th June, 2015, 09:54 AM
These car goes easy on obd done many of them gall works perfect

kenancatli
16th June, 2015, 11:01 AM
what went wrong I read K line?
maybe read and write CAN line?

what can I do now? can I use swap ecu?

regards

tunertool
16th June, 2015, 11:03 AM
You should be able to fix this!

kenancatli
16th June, 2015, 11:07 AM
tunertool what you mean?
Can you my help please?

gsmik
16th June, 2015, 11:24 AM
Used xprog-m to write flash (only BDM file). It does not test the ecu

warrio67
16th June, 2015, 11:33 AM
put ignition on
correct checksum with winols,
do ecu id before writing,
try to write on kline,
if you have mpps try to write with it

kenancatli
16th June, 2015, 12:03 PM
I do with gal2 bdm no connect to ecu
I read this ori file with gal2
I read on bench with bosch kts found no ecu!!!
xprog m can Write it ??
help please

morgano
16th June, 2015, 12:09 PM
The ori file you have cannot be written in BDM or Xprog, you need to take an ECU readout using BDM or XProg and mix it with your original.

If you put wrong pins to ecu BDM port maybe too late for the mircroprocessor and BDM port inside it is burnt.

kenancatli
16th June, 2015, 12:22 PM
If you put wrong pins to ecu BDM port maybe too late for the mircroprocessor and BDM port inside it is burnt?
Can repair it microprocessor? or can I swap ecu program??

morgano
16th June, 2015, 12:41 PM
Is common people feed ecu by bdm port, not pinout, in this condition if you reversed BDM pins on PCB pads you got fried ecu.

For using Fgtech BDM on bosch ecus you should take first flat cable plug to Fgtech, and the other side to a 10 pin adapter called fgtech-cmd that must have came with your fgtech set, and then connect another flat cable from that adapter to the bosch 10 pin adapter. Now the pins are right sorted.

Feed the ecu by pinout and the fgtech as you like, battery connected to red and black wires to the tricore boot cable plugged at db15, or AC-DC converter plugged on jack.

Power on ecu by switch (simulate key ignition) and click Connect on BDM page of fgtech sw. If all good then sw must identify processor, flash and eeprom.

gsmik
16th June, 2015, 01:02 PM
Read flash with xprog-m and put here. Pinout for xprog-m is in forum.

If you write flash without checksum galetto no read ecu with BDM or kline

kenancatli
16th June, 2015, 02:59 PM
hello
I need xprog m pinout connection to edc16c35!!!

it is good this connection?

overs0ull
16th June, 2015, 05:17 PM
yes this is the right pinout for bdm connection on xprog to edc16

tunertool
16th June, 2015, 05:26 PM
kenan! What tool you used for flashing? China clone?

quattrotr
17th June, 2015, 07:57 AM
Sure what else? Chinese clone V54 do that often on BMW EDC16C35, it's not first or last time... If you have tried to get car run then most probably your eeprom and flash immo data won't match too and is currupted. Even if you restore flash you have to match immo too...

kire106ka
17th June, 2015, 01:46 PM
I have one rule in working with cars do not touch something if you do not know how to repair in case to do some damage

kenancatli
17th June, 2015, 08:38 PM
Hey tunertool, euroclone Fgtech 2

kenancatli
17th June, 2015, 08:47 PM
Problem solved
Ecu broken
Swap dde7 Ecu ANd program now car run
Why broken Ecu ?
K line write maybe problem ? I do k line and Ecu dead!!!
CAN hıgh ANd CAN low write?
Maybe bad tuned file?
Or
Best regards

tunertool
17th June, 2015, 08:59 PM
K line writing will not kill ECU... maybe you killed by connect BDM wrong.

kenancatli
18th June, 2015, 09:57 AM
Hello tunertool
With Gal 2 do via OBD write give error after Ecu not found, Ecu not found Ecu kılled?
I try with BDM Fgtech Ecu not found! I try with BDM 100 china clone Ecu not found! Pinout same Fgtech ANd BDM 100? Bdm pinout?

Babos
18th June, 2015, 10:11 AM
WOW again ecu is dead?
i think your ecu go to sleep after not correct write procedure!?
And now need search how to wake up ecu.

kenancatli
18th June, 2015, 01:10 PM
Babos
I do more then 10 years chiptuning, first time Ecu dead! NeXT I do take action!!!
How what you mean not correct write procedure?
I read and write Battery voltage maybe problem 13,7 volt? More then 14 volt!

Babos
18th June, 2015, 05:36 PM
Babos
I do more then 10 years chiptuning, first time Ecu dead! NeXT I do take action!!!
How what you mean not correct write procedure?
I read and write Battery voltage maybe problem 13,7 volt? More then 14 volt!

ok can you share or send me original dump and mod file, then i can say you.
If you want can write in PM.

kenancatli
19th June, 2015, 11:46 AM
ok can you share or send me original dump and mod file, then i can say you.
If you want can write in PM.
hello babos here ori and mod file


Regards

Babos
19th June, 2015, 01:02 PM
I not see problem in mod file all is ok!
Best way for you remap that via BDM.
I dont know why ecu down on OBD.
One way try to remap that ecu in table via can line and can see again ecu down or all be good, but buy again ecu for test i think is to much for that car.

kenancatli
19th June, 2015, 03:55 PM
Next time I do via BDM edc16c35! Fgtech BDM it is good euroclone?

kenancatli
6th July, 2015, 07:09 PM
Aes flasher fgtech from bosnia bad tool

DR Race
6th February, 2018, 02:58 PM
Hy guys sorry to brother, i have to do this week one edc16c35 520d e60 , after reading this i am not so confident to do the job, I have a good kess clone eu purple pcb , till now tool work perfect on edc 16 vw , edc 15 Mercedes, edc 17 vag, and delphi dcm 3.5 Ford, I have done 1 e61 520 d 163 hp OBD with no problem , hase somebody bad experience with kess on this ecu , I have also mpps v18 and ktag here but I don't like to take ecu out from car !!!

Trimis de pe al meu SM-G930F folosind Tapatalk

sdtsedat
6th February, 2018, 03:36 PM
You can read/write this ecu with Kess and Fgtech without problem. Important with ignition, when ignition is half on, you can also read but NO write! So easy way to kill your ecu.
EDC17 bmw tricore don't use kess because there is checksum problem.

I use always fgtech for do bmw.
Succes,

DR Race
7th February, 2018, 12:05 AM
You can read/write this ecu with Kess and Fgtech without problem. Important with ignition, when ignition is half on, you can also read but NO write! So easy way to kill your ecu.
EDC17 bmw tricore don't use kess because there is checksum problem.

I use always fgtech for do bmw.
Succes,Thenks for your reply , by this car ignition is not with key anymore, this is a 2007 and it has a start buton, I will pay attention at what you say and I will report how job !
I have done 1 car with this ecu and no problem!

Trimis de pe al meu SM-G930F folosind Tapatalk

dominik.m
7th February, 2018, 12:19 AM
Mr sdtsesat is right. Fgtech read and write this ecu by OBD without problem.

DR Race
7th February, 2018, 12:24 AM
Mr sdtsesat is right. Fgtech read and write this ecu by OBD without problem.I have only kess , mpps , ktag here , I have ordered cmd flash but not received yet and customer don't whant to whayt!
I have also done this ecu with kess no problem, but I have read on forum that other guys have problem on this ecu!

Trimis de pe al meu SM-G930F folosind Tapatalk

DR Race
7th February, 2018, 01:18 AM
Joe shoud i whrite k-line or can ??? 2007 ?? Old i know ja k -line nur 2007 ?

Trimis de pe al meu SM-G930F folosind Tapatalk

sdtsedat
7th February, 2018, 03:08 AM
Joe shoud i whrite k-line or can ??? 2007 ?? Old i know ja k -line nur 2007 ?

Trimis de pe al meu SM-G930F folosind Tapatalk2007? I do it over can bus. Kline doesnt respond.

Your second answer, yes start stop button, you can press 1 time start and ignition is half on, in this status you can read/write but error when writing..

This ecu is easy to do, you can make backup with bdm.

If you are scared take ecu out and read with bdm and you are safe.

Verstuurd vanaf mijn SM-A520F met Tapatalk