PDA

View Full Version : FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386



Pages : [1] 2

fantomel
28th June, 2015, 12:37 PM
FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386


What you can find here:


1.For tool number 0386: ept file,fix file,hex dump and 2 versions of programs V54 used for it, the one from china and the AES November software.


2.For tool number 0475: ept file,fix file, hex dumps made from my tool and program V54 for it that does not need time back.


3.For both tools you have here how to connect to it, how to read firmware movie, how to write dump that you wish.


Reading and writing the mcu for this tool can be done with old Philips LPC 2000 software and USB-TTL adapter, preferd the one that uses PL2303 chipset. You need also a jumper in position to do that.
If you want to check CRP level of your NXP mcu you can do that with FlashMagic and USB-TTL adapter.
http://i61.tinypic.com/11h73sz.jpg


Password request on forum will be ignored, you have been warned not to spam topic with it.


Password: fantomelfree4galletto
Enjoy.

Music73
28th June, 2015, 12:59 PM
Hi..

I have a v54 Chinese clone and when plugged into usb is reconised as a galletto V54 but drivers are no longer correct drivers tried uninstalling and reinstalling and also differant PC's.. With this software do you think i could revive it.. It seems as though something is corrupt was fine one day then couple of days later it wouldnt play.

Cheers for any advice you can give..

morgano
28th June, 2015, 03:25 PM
after you reinstall V54 drivers need reinstall again "fgtech galletto edited1.0" witout deinstall it previously.

tunertool
28th June, 2015, 03:33 PM
:) :):) :):) :)

fantomel
28th June, 2015, 03:42 PM
ErrorsThe following errors occurred with your submission

toms4 has exceeded their stored private messages quota and cannot accept further messages until they clear some space.


Please don't spam topic regarding pass, you have PM for this. Don't force me to ignore requests from topic.
ONLY PM

Music73
28th June, 2015, 05:08 PM
after you reinstall V54 drivers need reinstall again "fgtech galletto edited1.0" witout deinstall it previously.

Already done this but thanks... Fantomel has told me what needs done (which is what i suspected).. so will report after i have done it.. Cheers

fantomel
28th June, 2015, 08:24 PM
Glad i could help. If something from my pack it's unclear please post your questions and i will answer gladly.

Meat-Head
28th June, 2015, 11:09 PM
Password request on forum will be ignored, you have been warned not to spam topic with it.
Password only by PM for active users with at least 20 posts after THANKS and REP

What a dick if that's your attitude then don't pass word stuff.

fantomel
29th June, 2015, 09:36 AM
Dear Meat-Head , my work, my choosing .
I agree with your signature but in part. If you would have known me then you would have seen this is not the case.
As it is my pack, with some of my work inside then it's my right to choose.
I am sick of all ppls out there keeping secrets instead of helping ppls. I do not sell a thing nor i did in this auto world just helped and i have posted a lot of stuff from my own work.
Hope this clears things out there and if you need to see my works search other forums for more.

dariobmw
29th June, 2015, 10:04 AM
Sorry fantomel but i'm poor and dumbass maybe my connection is S..T but i cant download the files from the link ...... is any chance
to be posted on another site ?

THANKS a lot for your work

fantomel
29th June, 2015, 10:14 AM
The following errors occurred with your submission



dariobmw has exceeded their stored private messages quota and cannot accept further messages until they clear some space.

Clear some space :) and PM me after. Or you can try and use megaDownloader that works great if your chrome or firefox has problems.

skywoker
29th June, 2015, 06:13 PM
Try to update my tool to 0745 and i have error from picture. Try everything on my xp sp3 laptop but not working. Maybe you help me..320292

fantomel
29th June, 2015, 08:02 PM
For that to work you tool needs to have proper firmware(hex), proper ftdi write fix and c++ librarys from what i see from your windows install. I think windows it's a little crazy in your case :).
P.S. Disable antivirus for folder fgtech since all exe are packed with VMProtect and that can give errors on some anti-virus programs.

skywoker
29th June, 2015, 08:05 PM
Windows is my problem?? I update hex and ftdi from your post. 0386 work, 0475 not work. What install in my windows for work 0475???

fantomel
29th June, 2015, 10:06 PM
driver from there and you have HERE (https://mega.co.nz/#!WxNkiJCD!eE8Yh-DOyr3GWdyVho1ZkBmL82KjCgFZ8w-OfuwoTrE) unpacked soft for it, same as the installer in my pack that for me works ok on xp vm, and w7x64 since i have 0475 tool.
I did not test the unpacked soft, it was shared in another forum.

Multipla
30th June, 2015, 12:07 AM
Naaaaaa,,,,, disistal your c++ all togheter optimal software is revo unistaller ( http://www.revouninstaller.com/revo_uninstaller_free_download.html) after install exnovo
Microsoft Visual C++ 2005 Redistributable
Microsoft Visual C++ 2008 Redistributable - x86/64 9.0.30729.17
Microsoft Visual C++ 2008 Redistributable - x86/64 9.0.30729.4148
Microsoft Visual C++ 2008 Redistributable - x86/64 9.0.30729.6161
Microsoft Visual C++ 2008 Redistributable - x86 9.0.30729.17
Microsoft Visual C++ 2008 Redistributable - x86 9.0.30729.4148
Microsoft Visual C++ 2008 Redistributable - x86 9.0.30729.6161
Microsoft Visual C++ 2010 x64 Redistributable
If you donte have reply, very very i think you have a worm https://it.wikipedia.org/wiki/Worm See you lather.

Multipla
30th June, 2015, 12:26 AM
http://www.prolific.com.tw/US/ShowProduct.aspx?p_id=225&pcid=41 is the driver of this adaptor
http://www.amazon.it/dp/B00K67X2XO/ref=asc_df_B00K67X2XO27265268/?tag=googshopit-21&creative=23394&creativeASIN=B00K67X2XO&linkCode=df0

skywoker
30th June, 2015, 07:01 AM
Hi guys, i solve the problem, many thanks to carmageddon user.

Trimis de pe al meu SM-T113 folosind Tapatalk

cawadany
30th June, 2015, 04:30 PM
FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386


What you can find here:


1.For tool number 0386: ept file,fix file,hex dump and 2 versions of programs V54 used for it, the one from china and the AES November software.


2.For tool number 0475: ept file,fix file, hex dumps made from my tool and program V54 for it that does not need time back.


3.For both tools you have here how to connect to it, how to read firmware movie, how to write dump that you wish.


Reading and writing the mcu for this tool can be done with old Philips LPC 2000 software and USB-TTL adapter, preferd the one that uses PL2303 chipset. You need also a jumper in position to do that.
If you want to check CRP level of your NXP mcu you can do that with FlashMagic and USB-TTL adapter.
http://i61.tinypic.com/11h73sz.jpg


Password request on forum will be ignored, you have been warned not to spam topic with it.


Password only by PM for active users with at least 20 posts after THANKS and REP

Hi, can I upgrade V48 (0084-0103) to V54 0386 or 0475? Thanks!

fantomel
30th June, 2015, 05:13 PM
ErrorsThe following errors occurred with your submission

cawadany has exceeded their stored private messages quota and cannot accept further messages until they clear some space.

mancinofranco
30th June, 2015, 06:41 PM
thanks fantomel

totalkey
7th July, 2015, 04:55 PM
Its will resolve that software crashing all the time?

Sent from my ASUS_T00J using Tapatalk

xirtam
20th July, 2015, 06:27 AM
fantomel (http://www.digital-kaos.co.uk/forums/member.php/40745-fantomel) thank you.

motorsport
20th July, 2015, 09:38 AM
What the diference with 386?

carmageddon
20th July, 2015, 10:10 AM
0386 are 6 month older, no stability, bad cracked

soundnavigator
20th July, 2015, 08:09 PM
On original Galletto can I make full backup when I read LPC2119 ?

carmageddon
20th July, 2015, 08:23 PM
i think have cpu locked (noread) original tool

j-sky
30th July, 2015, 02:40 PM
Hello
I have a Fgtech Galletto V54 EU made from car-prog.com
How can i found the version number on my fgtech ?

tango
30th July, 2015, 02:54 PM
hi when trying to install fgtech galletto edited1.0 my virus checker says its got w32: malware-gen
this isnt good or is it false?

heteromies
30th July, 2015, 03:41 PM
Hello
I have a Fgtech Galletto V54 EU made from car-prog.com
How can i found the version number on my fgtech ?

When software opened, look right up corner, there should be seen "version tool-0386" or" tool-0475" etc...

j-sky
30th July, 2015, 03:43 PM
When software opened, look right up corner, there should be seen "version tool-0386" or" tool-0475" etc...
Yes, but it's the serial number of the fgtech: it's Tool-01..

lolo818
12th September, 2015, 07:54 PM
Hello,

thank you for sharing, then install it on a clone V54 now in 0386?
I whant to update my clone V54, can you send me the password?
Thanks a lot!!

alcorte
13th September, 2015, 02:36 AM
Thank you. I have Eu clone v54 ( 0475).
can you send me password?

beltronics
13th September, 2015, 10:07 AM
hello, I have 0386 and wanted to upgrade.
thanks

fantomel
4th October, 2015, 10:23 AM
The following errors occurred with your submission



beltronics has exceeded their stored private messages quota and cannot accept further messages until they clear some space.


beltronics please tell when you make some space :)

KNS1
17th October, 2015, 03:30 PM
after flashing on 0475 button is not active...

heteromies
17th October, 2015, 04:11 PM
after flashing on 0475 button is not active...

Maybe wrong software version? What galletto sofware used with 0475? It need own software also. Should found that same upload what shared here.

KNS1
17th October, 2015, 06:22 PM
I use the program and the firmware from the archive from fantome

KNS1
17th October, 2015, 06:24 PM
and with 0386 0386 software for galletto works,please help!

KNS1
18th October, 2015, 11:35 AM
Please help

teerak2uk
18th October, 2015, 11:52 AM
Please help
????????? .

KNS1
18th October, 2015, 01:12 PM
after flashing on 0475 button is not active...

teerak2uk
18th October, 2015, 02:18 PM
after flashing on 0475 button is not active...
You need to install different software and copy/paste 2 files over

KNS1
18th October, 2015, 07:25 PM
Yes I do but the buttons are not active,and when back return the firmware 0386 and I use the program it works with galletto??????

teerak2uk
18th October, 2015, 07:26 PM
Yes I do but the buttons are not active,and when back return the firmware 0386 and I use the program it works with galletto??????
Are you doing fw and ept file?

KNS1
18th October, 2015, 08:44 PM
Yes i do....ept,eeprom

KNS1
19th October, 2015, 11:22 AM
decided the problem replaced the ft232.

JuamPa16
17th December, 2015, 08:08 PM
Hi Guys... I try tu fix my Galletto, and when i click in Download Flash, messagge apears. (Cannot Communicate with test board)... Any advice?. BR!

teerak2uk
17th December, 2015, 08:09 PM
Hi Guys... I try tu fix my Galletto, and when i click in Download Flash, messagge apears. (Cannot Communicate with test board)... Any advice?. BR!
Buy another or get kess

JuamPa16
17th December, 2015, 08:21 PM
Buy another or get kess

I receibed yestarday, its very new... When i read ID, works ok, but when i try to read download flash. Error.

teerak2uk
17th December, 2015, 08:30 PM
I receibed yestarday, its very new... When i read ID, works ok, but when i try to read download flash. Error.
Check you are selecting correct ecu also post pictures of your h/w pcb

gazvts
17th December, 2015, 08:35 PM
have you connected usb PC -> Galletto also ?

JuamPa16
17th December, 2015, 08:49 PM
Check you are selecting correct ecu also post pictures of your h/w pcb

https://drive.google.com/open?id=0B9-6Kt2zS3eKQkxDUTV1MzEwRHc


have you connected usb PC -> Galletto also ?

Yes i connected, but when read id, non light come up. But always read id.

PS: I try to change the firmware in LP2119

PS2: I try write the firmware whit lpc2000, and flash it correctly

marmaro
18th December, 2015, 08:12 AM
HI!
I,ve try read rf7 mazda ecu by obd : galletto read id ,but dont read flash and give some error.
My device is 0368,I tried k-line( doblo 1.9jtd,ducato 2,3 jtd) , can (astra H 1,7cdti, mazda3 1.6cdi), boot mode (corsa D 1.3cdti bosch) and it working properly.


347531
I have a question if the change the firmware on the 0475 allows me to read this ECU by obd?

Thanks in advance for any help

teerak2uk
18th December, 2015, 08:52 AM
HI!
I,ve try read rf7 mazda ecu by obd : galletto read id ,but dont read flash and give some error.
My device is 0368,I tried k-line( doblo 1.9jtd,ducato 2,3 jtd) , can (astra H 1,7cdti, mazda3 1.6cdi), boot mode (corsa D 1.3cdti bosch) and it working properly.


347531
I have a question if the change the firmware on the 0475 allows me to read this ECU by obd?

Thanks in advance for any help
Try it nothing to lose

pinotec
18th December, 2015, 09:19 PM
Dear Meat-Head , my work, my choosing .
I agree with your signature but in part. If you would have known me then you would have seen this is not the case.
As it is my pack, with some of my work inside then it's my right to choose.
I am sick of all ppls out there keeping secrets instead of helping ppls. I do not sell a thing nor i did in this auto world just helped and i have posted a lot of stuff from my own work.
Spero che questo cancella le cose l? fuori e se avete bisogno di vedere i miei lavori di ricerca altri forum per ulteriori.
fantomel
this patch " EvO.dll " not your work
do not boast about the work of others
and this patch fix ept because at every startup rewrite ept

cawadany
7th January, 2016, 11:28 PM
Someone has the hex dump of firmware 0084-0103?

cawadany
11th January, 2016, 04:59 PM
I have a problem with 475.... the soft crash at start on a notebook with win7 32bit. I have tried on another PC with win7 32bit and it starts. I have tried to make fresh installation of win7 on the notebook, but same problem..... Someone can help me?

venigo
19th January, 2016, 11:43 PM
Got a galletto 2 v54, what version is on the device?

Read EEPROM successful Device 0
0000 : 00 40 03 04 AD DA 00 00 A0 16 08 00 00 00 98 0A @. .. .. .. .. .. .. ..
0010 : A2 0E B0 12 32 18 05 00 0A 03 46 00 54 00 44 00 .. .. .2 .. .. .F .T .D
0020 : 49 00 0E 03 46 00 47 00 54 00 65 00 63 00 68 00 .I .. .F .G .T .e .c .h
0030 : 12 03 34 00 37 00 34 00 31 00 34 00 35 00 35 00 .. .4 .7 .4 .1 .4 .5 .5
0040 : 34 00 00 00 BF 4B CC B8 67 6B D7 2F 20 55 C8 7A .4 .. K. .. kg .. U. z.
0050 : 40 57 6D 3D 03 9B 1E 8E 4D BF B7 99 6A 31 F8 23 W@ =m .. .. .M .. 1j ..
0060 : 3A 84 4A 7A 65 78 98 70 C7 35 F1 2F 8C F8 1E 13 .: zJ xe p. 5. .. .. ..
0070 : EA 2E EB D8 C6 8B 94 60 A9 58 00 00 00 00 B5 60 .. .. .. `. X. .. .. `.
0080 : 2B 04 D4 FB 00 00 8B F5 CA 70 42 00 00 00 00 00 .. .. .. .. p. .B .. ..
0090 : 00 00 00 00 00 00 00 00 37 41 49 58 51 4F 32 35 .. .. .. .. A7 XI OQ 52

venigo
20th January, 2016, 12:31 AM
Possible to flash mcu galletto 2 v54 to 4 v54? 0475?

Thanks

venigo
20th January, 2016, 12:56 AM
Received a galletto 2 v54 (they says), but it is a v52... Is it possible to flash it to v54? Also what do you think of the quality of pcb?


http://imgur.com/a/Y8rW5


Looking forward to replies, thanks!


Some better pcb pics :fing20: :


http://imgur.com/a/YMSpr

jozoku1
2nd February, 2016, 11:00 AM
I do not need this software but cool.
Tnx man

AndyCZ
19th February, 2016, 09:22 AM
I have galletto 4, how can I identify which PCB version (0475 or 0386) I have?

358831358832358833

carmageddon
19th February, 2016, 09:37 AM
v54 china and eu have only 0386!

cokeaddict
9th March, 2016, 01:18 PM
FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386


What you can find here:


1.For tool number 0386: ept file,fix file,hex dump and 2 versions of programs V54 used for it, the one from china and the AES November software.


2.For tool number 0475: ept file,fix file, hex dumps made from my tool and program V54 for it that does not need time back.


3.For both tools you have here how to connect to it, how to read firmware movie, how to write dump that you wish.


Reading and writing the mcu for this tool can be done with old Philips LPC 2000 software and USB-TTL adapter, preferd the one that uses PL2303 chipset. You need also a jumper in position to do that.
If you want to check CRP level of your NXP mcu you can do that with FlashMagic and USB-TTL adapter.
http://i61.tinypic.com/11h73sz.jpg


Password request on forum will be ignored, you have been warned not to spam topic with it.


Password: fantomelfree4galletto
Enjoy.
Am I correct here in thinking, that if I have CRP2, then I can still safely write to it (and change it back later if I wanted), I just can not read the current info ?

toms4
9th March, 2016, 02:06 PM
Correct, you can not read content when CRP2, but you can write.

morphvale
10th March, 2016, 12:05 AM
FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386

Thanks mate, this worked perfectly fine. Got a v54 China Galletto to play with on my car, and it was version 0386. Found it really annoying that the software for it would not run under Windows 10 so I had to create a VM to run either Windows 7 or Windows XP.
However, that only worked under my Windows 10 x64 laptop, but not my Windows 7 tablet, which is 32 bit. That made it a bit difficult, as the software has VM protection, so I had to trick it into thinking it was not running on a VM, but that had to be switched off every time I wanted to copy new files to the VM.
Found your posts everywhere when searching for 0386 to 0475 update, and since it looked like my board had all the right components (even the right ones on the most part), I got a PL2303 USB-TTL adapter (not genuine, as the latest driver would not work) and did the soldering. Downloaded the Magic Flash tool, but neither that nor the Phillips tool would work to write after I erased the device (said it was CRP 2 or 3 when I checked initially then CRP disabled after the erase).
I played with the settings and flashing procedure a few times, but that always kept failing following your steps and I thought I was left with a brick.
I eventually ended up erasing the NXP flash with the Phillips tool, closing it, disconnecting the device, then opening Magic Flash and writing it back with that at 19200 without erasing first. That finally worked.
I then did the FTDI update, and after reinstalling drivers, I was able to run the software on Windows 10, both 32 bit and 64 bit just fine.
Did not go to the car yet and test, as I'm also waiting for Omron relays and ZVN and ZVP transistors, but I see no reason why it should not work.

B19hly
10th March, 2016, 09:03 PM
Hi guys need some help with my tool , I bought it a few years ago and its been sat there doin nothing , I been using mpps , I wantto get this Galleto working and need your guys help , I will post some picture of it , I was sent a key once when I sent my HW id , now the email is not working , if any one can help me get this working I would really appreciate it.

Thanks guys
Yonz

B19hly
10th March, 2016, 09:10 PM
These are the pics.

362974362975362976

cokeaddict
11th March, 2016, 11:40 AM
Correct, you can not read content when CRP2, but you can write.

Thanks, when I check with flashmagic, it says CRP is at level 2 or 3.

With the phillips tool I can not download the flash.

But my question is, how do I know which file to write with the phillips tool ?

FGTECH 0475 NO USE DTR RTS
FGTECH 0475 WITH USE DTR RTS 1.10
FGTECH 0475 WITH USE DTR RTS
lpc2119 0475 19200 with vector calc
lpc2119 0475 19200
lpc2119 0475 NO USE DTR RTS 1.10

cokeaddict
11th March, 2016, 12:04 PM
Ahh, ignore my last post.

I see there all exactly the same.

carmageddon
11th March, 2016, 12:25 PM
this is the right setup for philips, red setup as first operation then blu.

http://s12.postimg.org/j7vpopzbt/SETUP_LPC2000.jpg (http://postimg.org/image/j7vpopzbt/)

cokeaddict
11th March, 2016, 12:34 PM
Thanks, I followed the steps and flashed it with the hex.

Then updated the ept and the eeprom.

Finally I installed the 0475 sw, but when I run it, I get a message saying windows version higher than vista detected, applying 2nd patch, then nothing happens.

carmageddon
11th March, 2016, 01:08 PM
on netbook with seven (with max resolution 1024x600) dont work fgtech, work on netbook with resolution 1024x600 only with XP, or notebook or desktop

morphvale
11th March, 2016, 01:09 PM
Did you uninstall it (with delete driver option ticked) from device manager then reinstall the drivers from the Driver interfaccia folder? It will not work otherwise.

cokeaddict
11th March, 2016, 01:26 PM
Did you uninstall it (with delete driver option ticked) from device manager then reinstall the drivers from the Driver interfaccia folder? It will not work otherwise.

yes I have tried that (if wrong driver is installed, then it asks for the FTD2XX.dll instead).

cokeaddict
11th March, 2016, 01:46 PM
Strange, works fine with my Windows 10 Pro x64 laptop, but not with my Windows 7 Ultimate x64 Desktop

morphvale
11th March, 2016, 05:51 PM
I get some strange behavior on my Win 10 x32 tablet as well. Whenever I start the tablet and try to run the app, nothing will happen on the first open. I get the message about second patch, then nothing. If I open the task manager and wait for EOBD2.exe to close itself, when I open it the second time it will work just fine. Two other laptops with Win 10 x64 don't have this issue.

fantomel
23rd March, 2016, 10:58 PM
all depends on visual c+ libs you have installed and also .net version. on x64 i advice you to install all versions x86 and x64 to be ok. .net 4.52 also might be needed.

morphvale
24th March, 2016, 09:30 AM
It doesn't really bother me, I just wait for it to close and open it up a second time and it works just fine.
One thing that is annoying however, is the fact that every now and then, the application completely hangs until the timers expire. For my EDC16C34 on my Ford Focus 2, I select the file and start the flash (that takes about 12 minutes to write). Once the flash is finished, the application prompts me to turn of the dashboard and wait for three minutes. I do that, and click Ok, and at that point the application just hangs for the required 3 minutes. After the time passes, the application reacts again, asks me to turn on the dash and wait for another 3 minutes. After clicking Ok, the application hangs again for 3 minutes. I just wait for the time to pass knowing (i.e hoping) the app will resume working, but it's a bit annoying.

Matttes
28th March, 2016, 06:45 PM
Hi all,
have anybody link for donwload from other site than mega?
I cannot download this. But I don?t know why. I create registration in mega, but larger file about 300Mb in 97% was stopped download.
Can help to me anybody?
Many many thanks
BR Matias

teerak2uk
28th March, 2016, 07:18 PM
Hi all,
have anybody link for donwload from other site than mega?
I cannot download this. But I don?t know why. I create registration in mega, but larger file about 300Mb in 97% was stopped download.
Can help to me anybody?
Many many thanks
BR Matias
Use Chrome browser or install Megasync app

Matttes
28th March, 2016, 07:42 PM
Chrome solved my problem. I use usually firefox.
Many many thanks. You save my life. :-)

Multipla
28th March, 2016, 10:41 PM
Kindly let me know which part of the FGTECH 53 to be repair to read in Tool_boot_mode the MCU St10f .......? thank you

tango
28th March, 2016, 11:22 PM
Chrome solved my problem. I use usually firefox.
Many many thanks. You save my life. :-)

you can use megadownloader too

minimex
31st March, 2016, 11:00 AM
Hi friends,
can someone confirm the action with MPC55xx (no 5xx)
in ECU Volvo/Renault E5, TRW.
Thanks

Multipla
31st March, 2016, 11:55 PM
Nobody help me?

dominik.m
1st April, 2016, 04:25 AM
ECU Volvo/Renault TRW . Galetto read and write without problem.

CustomCars
1st April, 2016, 08:55 AM
Nobody help me?

Hard to say.
1. check connection.
2. post here few pcb HQ photos.

electronistul21
1st April, 2016, 11:42 AM
try your fgtech in bootmode first time.if work fine,need work and MPC55xx

minimex
1st April, 2016, 10:02 PM
Hi,
dominik.m:
picture a little small, but you can see that the processor MPC5xx ... not MPC5554!

dominik.m
1st April, 2016, 11:23 PM
minimex.

And this small picture fits You?

MPC5554 is in him?

minimex
2nd April, 2016, 09:14 AM
Hi.
And what these ambiguous words (such our - Polish).
On first image in increasing can be see MPC565, now is ok, thanks.
...
But to concrete, in my case, as the picture, where is the problem?
Connection ok, items on the pcb correct.367288
With MPC 5xx processor family I do not have a problem.
The KTag reads/writes ok.

cristofir
2nd April, 2016, 08:11 PM
Thank you Fantomel,all is good!

jsg1200
31st July, 2016, 02:18 AM
Very thanks! I need test this fix.

Regards ;)

cokeaddict
31st July, 2016, 10:09 AM
Does anyone have any idea on how to get it to work correctly with an MSS54HP and ST chips in bdm mode.

The eeproms are ST M29F400BB, however the fgtech detects them as 29F800BT, which means it dumps 1024kb instead of the correct 512kb and also means you can not write back.

It works perfectly with AMD AM29F400BB eeproms.

titinou67
4th August, 2016, 09:59 AM
Fantomel you are my h?ro , I have safe my two FgTech a AES and clone chin... Thanks a lot an sorry for my language . :biggrin:

Silver740
13th August, 2016, 09:17 AM
Hi, is this PCB good? Made in China.

392105

heteromies
13th August, 2016, 11:06 PM
Hi, is this PCB good? Made in China.



No. i rework these daily.

smirnoff_rules
13th August, 2016, 11:10 PM
Tell us what's wrong with it ?

smirnoff_rules
11th September, 2016, 05:12 PM
just waiting for my reader to turn up and was looking at updating 0386 but wondered what these where

https://i.gyazo.com/f2fb6290e98c284b29456dcc87d63183.png

jakesman
11th September, 2016, 05:36 PM
it is to change tool number from 386 to 475
EPT file u use with mprog for the ftdi chip reprograming and the other is used with ftreadwrite for eeprom , i use it when i flashed mine from 386 to 475 after u write the mcu flash u need this also

smirnoff_rules
11th September, 2016, 05:44 PM
ok so theres 3 files to rewrite . mine is ftdi , and why is there 3 epprom files and you also read/write with Philips Flash Utility 2.2.3 . video is only showing Philips Flash Utility

vanos batam
11th September, 2016, 06:04 PM
I rework it with different with fantomel picture..

azibi130
11th September, 2016, 06:52 PM
ok so theres 3 files to rewrite . mine is ftdi , and why is there 3 epprom files and you also read/write with Philips Flash Utility 2.2.3 . video is only showing Philips Flash Utility

i had compared those 3 file and 0475_v54 files are the same (only dif names), 0475_v53 it's diff. (these 3 files are for you choose which one to write fwrite)

ept file is for mprog.

phillips utillity is for mcu hex programing for update firmare

smirnoff_rules
11th September, 2016, 06:58 PM
so have to write 3 new files to box ? why are these different names then

https://i.gyazo.com/198660f6f48ed2ca2f57b1eca186595a.png

dont understand why this isnt clear in info

edit , found this from op

All those files are the same, are just proof that they were extracted using different drivers and different options checked in program. all of them worked, as proof is there. The only problem is the ttl adapter implementation + nxp lock that can be checked also.

azibi130
11th September, 2016, 07:28 PM
no mate, i was telling u about the files that are in 0475_fix folder.

that folder is for mcu programmming, i haven't done this changes in my v54, only tomorrow will try bdm and see what happens, then maybe will change relays

smirnoff_rules
13th September, 2016, 04:03 PM
sorted mine today . software alot more stable , didnt want to write drivers on win 10 ? but wouldnt use on that , works great on toughbook with xp

https://farm9.staticflickr.com/8051/29544777542_2c8d00b87e_b.jpg

azibi130
13th September, 2016, 11:28 PM
you use 0475 software with stock galletto pcb?

smirnoff_rules
14th September, 2016, 07:17 PM
you use 0475 software with stock galletto pcb?

yea , l havnt got around to replacing stuff , l dont use alot , have kess and ktag eu , but galletto has never not worked on the stuff l tried so far , software was a bigger problem to me

warrio67
15th September, 2016, 07:56 AM
hello i need some help
i have updated mine 0386 reworked
flashed all version 0475 : mcu , ept , eeprom,and installed new driver and new software 0475
when i start software i have a message
"windows vista or above detected "
software run with all button inactive (grey)
i run on laptop win 7 / 64bit

any advice are welcome
thanks

skywoker
15th September, 2016, 08:05 AM
For this software you need 0475 firmware in LPC2119

smirnoff_rules
15th September, 2016, 09:48 AM
HAVE YOU ADDED NEW DRIVERS to unit 64bit might be your problem , wouldnt work on my 64bit , driver wouldnt install

carmageddon
15th September, 2016, 10:57 AM
i use 32 bit driver on 32 or 64 and have no problem, i think problem is not driver.

with seven 32-64 the popup "windows vista or above detected" appear at each start

smirnoff_rules
15th September, 2016, 11:03 AM
true , on xp mines says using xp or under disable one patch and opens fine , not sure why win10 dosnt install driver ,

cokeaddict
15th September, 2016, 11:29 AM
true , on xp mines says using xp or under disable one patch and opens fine , not sure why win10 dosnt install driver ,

Works fine with windows 10 x64 pro, you have to press shift and select shutdown, go into the recovery options and select start without driver signing.

Then when it restarts you can install the driver.

Also once installed, when you start the program, do not plug the v54 in, until you have pressed ok on the 2nd patch message that pops up.

warrio67
15th September, 2016, 12:01 PM
i have installed driver from 0475 setup directory.
i see FGtech in device manager, soft run after message "windows vista or above detected" but all button are greyed (inactive)

ghironfa
27th September, 2016, 04:05 PM
thanks Fantomel......all ok its work...

pulsar2000
27th September, 2016, 08:04 PM
Always the same old: PM for Pw. and Below.,
Smirnoff or someone maybe PM me the PW, Mates, Desperate to try the mega Link, as got a chinky roll back Galletto, Cheers,,,,

The following errors occurred with your submission



fantomel has exceeded their stored private messages quota and cannot accept further messages until they clear some space.

pulsar2000
27th September, 2016, 08:05 PM
Mate clear your inbox would like to try your Mega Link, Cheers


FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386


What you can find here:


1.For tool number 0386: ept file,fix file,hex dump and 2 versions of programs V54 used for it, the one from china and the AES November software.


2.For tool number 0475: ept file,fix file, hex dumps made from my tool and program V54 for it that does not need time back.


3.For both tools you have here how to connect to it, how to read firmware movie, how to write dump that you wish.


Reading and writing the mcu for this tool can be done with old Philips LPC 2000 software and USB-TTL adapter, preferd the one that uses PL2303 chipset. You need also a jumper in position to do that.
If you want to check CRP level of your NXP mcu you can do that with FlashMagic and USB-TTL adapter.
http://i61.tinypic.com/11h73sz.jpg


Password request on forum will be ignored, you have been warned not to spam topic with it.


Password: fantomelfree4galletto
Enjoy.

smirnoff_rules
27th September, 2016, 08:20 PM
Password: fantomelfree4galletto

im sure he will be ok

please thank fantomel in first post if you lot use this link and password

pulsar2000
27th September, 2016, 08:42 PM
Password: fantomelfree4galletto

im sure he will be ok

Nice 1 mate :>

pablo1971
1st October, 2016, 06:11 PM
Can anyone help...re flashed 0836 china fgtech to 0475---flashed the mcu -usb fix and mprog etc...re installed 0475 software and re installed the new drivers for fgtech in device manager ..program opens..but the LOW VOLTAGE is greyed out..

smirnoff_rules
1st October, 2016, 06:27 PM
are all the buttons grayed out to

pablo1971
1st October, 2016, 06:31 PM
are all the buttons grayed out to

yes they are.

smirnoff_rules
1st October, 2016, 06:36 PM
it only happened to me once when drivers didnt install right and for me didnt like 64bit

pablo1971
1st October, 2016, 06:42 PM
it only happened to me once when drivers didnt install right and for me didnt like 64bit


thanks.will give it another go ......im using xp.

smirnoff_rules
1st October, 2016, 07:00 PM
remember your using the new driver thats in the pack you downloaded ftdi one

pablo1971
1st October, 2016, 09:37 PM
remember your using the new driver thats in the pack you downloaded ftdi one
finally got it sorted...0386 to 0475 all working..

pulsar2000
1st October, 2016, 09:44 PM
finally got it sorted...0386 to 0475 all working..

Great, dont suppose you got a step by step ?
or shall i skip to page 1 and do a read of the entire thread,
i also have same China clone, roll back date version,
Thanks

pablo1971
1st October, 2016, 10:25 PM
basically i flashed the mcu,then mprog and ept file...now uninstall all gallatto sw and start another install...when the program is installed plug in fgtech..device manager etc...and install the drivers from FGTECH-NEW DRIVERS FOLDER..when drivers are installed...remove usb and re connect...then start the sw...mine came up...WITH no voltage..but shows 12v with power connected...all seems ok..

Hope that helps.

pulsar2000
1st October, 2016, 11:04 PM
Nice 1 Mate, will have a go Monday,

Cheers

absetup
2nd October, 2016, 08:47 PM
Need to teste this too


Envoy? de mon iPhone en utilisant Tapatalk

pablo1971
3rd October, 2016, 05:28 PM
just a bit of a update--0475--tried it on a edc17cp14...boot...read/write all ok...but tried it on a edc17c19 insignia...boot..did a read...but would not write a mod file back....comes up with chks not supported...i did think the 0475 was at fault...so re flashed the fgtech to 0386...tried and still the same...anyone come accros this....this fgtech is a new ish one tbh.

pulsar2000
3rd October, 2016, 10:42 PM
just a bit of a update--0475--tried it on a edc17cp14...boot...read/write all ok...but tried it on a edc17c19 insignia...boot..did a read...but would not write a mod file back....comes up with chks not supported...i did think the 0475 was at fault...so re flashed the fgtech to 0386...tried and still the same...anyone come accros this....this fgtech is a new ish one tbh.

Yea usual FGTECH Shite,,,, get a Ktag, and less problems Boot mode Tricore,


Fgtech great tool BDM and Obd, 5/10 Boot mode in my opinion,,,,,
K tag wins hands down on Boot mode Ecu`s

smirnoff_rules
3rd October, 2016, 11:09 PM
mine is shit too , worked fine on edc15 on desk but useless on bdm , put back in box and left to get dust on lol , ktag is 100% better

azibi130
4th October, 2016, 04:45 PM
my v54 work ok so far...WITHOUT ANY CHANGES in Hardware or Software

edc15 - k
edc16 - k/can/bdm
marelli 6jf/6f3 - bdm/can/k

CHAVCAR
20th October, 2016, 04:39 PM
405014
What most complete software can work in my interface, currently use this software and hardware.

kptuning
29th October, 2016, 09:50 AM
Hi. Have New 0386 china interface. Read 2011 golf 1,2 tsi yesterday without problem. Can anyone comfirm that writing is good also? Br

smirnoff_rules
29th October, 2016, 09:55 AM
only difference l can see is programs more stable and working on windows 10

beltronics
29th October, 2016, 10:34 AM
only difference l can see is programs more stable and working on windows 10
It can be used in Windows 10?
that version need?
Thank you

smirnoff_rules
29th October, 2016, 10:59 AM
0475 and later driver in the first post

kospoz
30th October, 2016, 07:50 PM
Can someone tell if fg is good with renesas mode? Opel denso for eg.

carmageddon
30th October, 2016, 08:08 PM
i made many denso petrol and diesel without problem with fg v53

kospoz
30th October, 2016, 08:19 PM
i made many denso petrol and diesel without problem with fg v53

I have both of them and i can say that v53 is better from v54 opinion for my tools.i have tried opel denso sh7059 with v54 nothing at all.with v53 read but at end giving error wire 2 and 3.also with ktag unable to read it.have you any idea?someone told that the cable has reverse colours.

svvag2000
30th October, 2016, 08:48 PM
....perfectly works on windows10


https://youtu.be/VKQreCM4XhY

youk
27th November, 2016, 10:14 PM
hi, can you send me the hex for 50-103 or 48-103 please ?

smirnoff_rules
27th November, 2016, 10:18 PM
not sure what hex you mean but all files here http://www.digital-kaos.co.uk/forums/showthread.php/477215-FGTECH-GALLETTO-V54-FIX-EPT-HEX-DUMP-amp-PROGRAM-FOR-0475-AND-0386?p=2857171&viewfull=1#post2857171

dadal
27th November, 2016, 10:58 PM
I have both of them and i can say that v53 is better from v54 opinion for my tools.i have tried opel denso sh7059 with v54 nothing at all.with v53 read but at end giving error wire 2 and 3.also with ktag unable to read it.have you any idea?someone told that the cable has reverse colours.

I could read renault sagem s3000 full flash , but could not write to back ecu,, Galetto show in the menu of renesas " Rx and Tx " bu dont give more info about that.
I cant renesas set in boot mode, I have read datashet SH7055 ( 1000 pages :) ) I know Rx and Tx pins are related with Bootmode..
maybe someone knows what to do with these pins
maybe manuel /diagram is wrong

carmageddon
28th November, 2016, 08:06 AM
rx-tx are white and violet on boot cable

you can see on picture where you must place rx-tx, need only green, white, violet and two links on pcb then you can write

youk
29th November, 2016, 09:01 PM
hi, can you send me the hex for 50-103 or 48-103 please ?

(not 475 or 386)

Allky86
4th December, 2016, 01:18 AM
how? send me to PM .thanks

montemoto
24th December, 2016, 01:55 PM
Password THANKS

marsete
24th December, 2016, 02:19 PM
FGTECH GALLETTO V54 FIX EPT HEX DUMP & PROGRAM FOR 0475 AND 0386


What you can find here:


1.For tool number 0386: ept file,fix file,hex dump and 2 versions of programs V54 used for it, the one from china and the AES November software.


2.For tool number 0475: ept file,fix file, hex dumps made from my tool and program V54 for it that does not need time back.


3.For both tools you have here how to connect to it, how to read firmware movie, how to write dump that you wish.


Reading and writing the mcu for this tool can be done with old Philips LPC 2000 software and USB-TTL adapter, preferd the one that uses PL2303 chipset. You need also a jumper in position to do that.
If you want to check CRP level of your NXP mcu you can do that with FlashMagic and USB-TTL adapter.
http://i61.tinypic.com/11h73sz.jpg


Password request on forum will be ignored, you have been warned not to spam topic with it.


Password: fantomelfree4galletto
Enjoy.
Fantomel you are the best...thanks!!

marsete
25th December, 2016, 10:12 PM
[Quote = Multipla; 2738504]? Nadie me ayude [/ quote]Hello friend,in folder the documents(fg_tech) is intructions for read your ecu

trinicolin
27th December, 2016, 02:38 PM
Hi guys, what are the advantages of having 0475 over 0386 that is being used on win xp?

smirnoff_rules
27th December, 2016, 03:10 PM
later software is more stable and works on win10 ok too

beltronics
27th December, 2016, 05:07 PM
later software is more stable and works on win10 ok too
What adapter do I need to change firmware?


Thank you

teerak2uk
27th December, 2016, 05:24 PM
What adapter do I need to change firmware?


Thank you
Start from post #1

beltronics
27th December, 2016, 06:33 PM
How do I install software 0475?
Install the V54 for 0475 all Win and then copy the 2 files from the Patch No Reg Key folder v54 0475 into the directory where it was installed.


And the program does not start

smirnoff_rules
27th December, 2016, 06:40 PM
have u added 0475: ept file,fix file,

is your driver installed

mrchip
2nd January, 2017, 02:55 PM
Hi Mates,

I wanted to rework my galetto ( replace U16-U23 by E-L9637D)
as you can see in the photos some soldering pads of U16 broken. I want to connect these legs of L9637D directly via wires to circuit board,( not via traces because pads are broken).

I cant find/see connection points( trace) of some legs on circuit board.
Can someone check it please ( continuity test by multimeter) ? I cant find connection point of 3 pads/pins
418758

https://s29.postimg.org/o74393tjr/Knipsel.png

hass42
7th January, 2017, 05:27 PM
Hello all,
can someone help me with how to determine what tool # I have?

419821

carmageddon
7th January, 2017, 06:06 PM
first series of v48

hass42
7th January, 2017, 06:27 PM
That old huh... OK thank you

Hass42

koolstuff
10th January, 2017, 10:42 PM
Can i flash it with Jlink or Ulink2? Thanks.

daniele1968
15th January, 2017, 09:51 PM
hi to all anyone of you knows if it is possible read and wryte FTDI 232R with programmer? imessed up my galletto 54 chip and i dont find the way out any solution will be acepted tanks

dadal
23rd January, 2017, 04:10 AM
i cant download flash ( like as show in video), problem is I think CRP level
how to dissabble CRP2 or 3 ?

carmageddon
23rd January, 2017, 07:20 AM
v54, dont need to be disassemble, only erased from world (and from lpc with v53)

dadal
24th January, 2017, 10:37 PM
finally did it,
:celticparty:


I have now full reworked galetto ( hard & soft )

Thanks to Fantomel and Please do not forget to give him thanks

and special thanks to Carmageddon, for his support ( for hardware and software )

asix
29th January, 2017, 04:03 PM
Hello friends! I have a problem with the software "V54 for 0475 Win all." I'm with Win7 Os. Of ten attempts to start the program it runs only once. I get the following error. Can anybody help me to resolve the problem? Thanks!
424734

kostrz3
30th January, 2017, 12:54 PM
hello please me send dump ept and eprom from adapter usb ttl

Suv4x4
1st February, 2017, 05:27 AM
I have bought a chinese clone V54 latest claimed 2017 version. I have done all the tricks possible to make this tool work. I have written n number of ept files till now, followed all the different processes like setting the system date to 1/1/2013 , installing correct drivers and what not. But this tool does not budge. When i connect to any of the cars the software opens properly, it shows tool no 0386, it shows correct voltage. But when i select the driver and try to connect to any of the cars it throws an error as shows in the picture
Attention!! Send File C:\FGTECH\EOBD2_LOG\_ebod2_XXXXXX_ERR.gal to support@fgtechnology.it

I have been breaking my head over this tool since 5 days now without any success. I have not done any hardware changes yet. I have ordered a USB to TTL converter to write MCP with 0475 version now. But i doubt if that will work for me.

Request all the senior members and expert to please help me on this.

425257425258

Suv4x4
8th February, 2017, 02:49 PM
I followed all the software changes suggested by Fantomel in the opening post. My tool now shows 0475 and when i open the 0475 version EOBD2 i see correct voltages etc. But still my tool cannot read any ecus

I am trying only through OBD port, i do not need BDM feature. Can someone please point out what controls read thru OBD and why i get the error mentioned in the above post

vicious425
8th February, 2017, 03:49 PM
Sorry, i dont get it. what do you do with these files? and whatsthe purpose?? i am new to this so excuse the dumb questions :)

gazvts
8th February, 2017, 04:10 PM
I followed all the software changes suggested by Fantomel in the opening post. My tool now shows 0475 and when i open the 0475 version EOBD2 i see correct voltages etc. But still my tool cannot read any ecus

I am trying only through OBD port, i do not need BDM feature. Can someone please point out what controls read thru OBD and why i get the error mentioned in the above postdid you check over your obd cable on dsub & obd side ?

dadal
8th February, 2017, 06:19 PM
I followed all the software changes suggested by Fantomel in the opening post. My tool now shows 0475 and when i open the 0475 version EOBD2 i see correct voltages etc. But still my tool cannot read any ecus

I am trying only through OBD port, i do not need BDM feature. Can someone please point out what controls read thru OBD and why i get the error mentioned in the above post

do you use obd adapter ?
this one:
and try it with an other USB cable ( not original of galetto),,I use an better usb cable
427129

Suv4x4
9th February, 2017, 07:45 AM
Thanks a lot Dadal and gavts , i changed the USB cable. the connectivity to the outer casing was missing. Now the tool works perfectly. The best part is now its 0475 version. Was able to read and write a Delphi DCM 3.2 ECU

shooting
12th February, 2017, 05:29 PM
I can't get this to work in Windows10, does anyone have a solution?

see pictures

wbr

gazvts
12th February, 2017, 07:40 PM
if yours still 0386 firmware it will not work with the software you have installed . need to either flash it with 0475 fw or try running aes version on it which i personally never tested that on win 10 system

vasco fernandes
12th February, 2017, 07:51 PM
I upgraded 0386 to 0475 and works perfect in windows 10 32 bits

obeids
19th February, 2017, 07:52 AM
Hi there



I would like to know what are the EXPERTS suggestions on buying the FG TECH?
I would like to do mostly the BMW TRICORE ECU.
Should I buy from ALiexpress and just do this update here or are there any Components also that require changing?
Or should I buy something from Ebay such as this one in this link?

http://www.ebay.com/itm/FG-TECH-GALLETTO-4-V54-VERSION-EUROPEAN-MASTER-JTAG-BDM-TRICORE-DPF-EGR-/272266241177?hash=item3f64552499:g:8bUAAOSwhOVXeTw s&vxp=mtr


Thanks alot

shooting
19th February, 2017, 12:45 PM
Hi there



I would like to know what are the EXPERTS suggestions on buying the FG TECH?
I would like to do mostly the BMW TRICORE ECU.
Should I buy from ALiexpress and just do this update here or are there any Components also that require changing?
Or should I buy something from Ebay such as this one in this link?

http://www.ebay.com/itm/FG-TECH-GALLETTO-4-V54-VERSION-EUROPEAN-MASTER-JTAG-BDM-TRICORE-DPF-EGR-/272266241177?hash=item3f64552499:g:8bUAAOSwhOVXeTw s&vxp=mtr


Thanks alot

This is just ?30 clone tool.... search and you'll find a cheaper one....

wbr

vasco fernandes
19th February, 2017, 08:27 PM
Hi there



I would like to know what are the EXPERTS suggestions on buying the FG TECH?
I would like to do mostly the BMW TRICORE ECU.
Should I buy from ALiexpress and just do this update here or are there any Components also that require changing?
Or should I buy something from Ebay such as this one in this link?

http://www.ebay.com/itm/FG-TECH-GALLETTO-4-V54-VERSION-EUROPEAN-MASTER-JTAG-BDM-TRICORE-DPF-EGR-/272266241177?hash=item3f64552499:g:8bUAAOSwhOVXeTw s&vxp=mtr


Thanks alot

this is PCB china

phl0at
19th February, 2017, 09:53 PM
Actually you will see descriptions like "china clone" and euro "clone". The fact is euro clone is chinese clone reworked (or not) which works the same way the pure chinese one does. Do not bother searching for a GOOD CLONE cause there is no such thing. Buy the cheapest one.

heteromies
20th February, 2017, 12:23 AM
Actually you will see descriptions like "china clone" and euro "clone". The fact is euro clone is chinese clone reworked (or not) which works the same way the pure chinese one does. Do not bother searching for a GOOD CLONE cause there is no such thing. Buy the cheapest one.

LOL ^^ LOL ^^

phl0at
20th February, 2017, 09:08 PM
LOL about what? I guess companies like MagicMotorsports, Dimsport, Dimtronic, EVC make euro clones of FGTech products so there are some really neat ones :)
I guess your "LOL" stands for "I have euro clones and they are good with no chinese HOWTO INSTALL VIDEOS" ?

mickey51
21st March, 2017, 06:57 PM
hello i m trying for upgrade to 0475 but when i would like download files lcp, the phillips flasher says "cannot communicate with test board" but i can read the s?rial number. thanks you for your help

jsg1200
22nd March, 2017, 10:56 PM
Hi. I rework mi fgtech with your photo.

But Bdm, one day work, and the next day not work. Can you say me that component is to BDM?

Regards ;)

P.D.: I are studiying how to update of 0475 and programmer lpc...

p38
23rd March, 2017, 08:39 AM
hello i m trying for upgrade to 0475 but when i would like download files lcp, the phillips flasher says "cannot communicate with test board" but i can read the s?rial number. thanks you for your help
I have the same problem if it is LPC protected?

queroseno
23rd March, 2017, 01:02 PM
[CITA = p38; 2.988.333]? I tienen el mismo problema si es LPC protegido [/ QUOTE]


Some gallettos have protection in processor, that is why it does not communicate, the solution, change processor for a virgin and already communicates

inter5353
10th April, 2017, 12:46 PM
hallo,,,,pass bitte
:)

shooting
10th April, 2017, 07:15 PM
Has anyone got a fix for Windows10 64bit yet?

wbr

morgano
11th April, 2017, 08:26 AM
Has anyone got a fix for Windows10 64bit yet?

wbr

Funny. Made me laugh a bit. ;)

nofal2220
14th April, 2017, 04:44 PM
:stung: thanks

kingarthas
16th April, 2017, 11:13 AM
Hi,


What is better firmware for you 0475 or 0386? Mine has 0386 and tricore works good, however only on win7 with date changing.


Reading stock fw was not possible. So I did direct erase. And all gone ok in writing 0475.

Now I use 0475 soft, and make it run on win 10 x86 by shifting program to c:/fgtech


For those that still run fw 0386 you can try just pase the ""Patch No Reg Key v54 0475"" to 0386 folder c:/fgtech . And run the program from EOBD2.exe instead of EOBD2S.exe

Then just delete the 2 files if you want to run EOBD2S.exe

Marek_Spy
22nd April, 2017, 09:50 PM
Hi
Can someone solve the problem with windows XP and galletto V54? Working 0386 but not working 0475.

lsdlsd88
22nd April, 2017, 10:15 PM
Any suggestion?

maybe try swapping tx and rx pins?

morgano
23rd April, 2017, 12:38 AM
No need swapping any pins, he already connected, just need to erase nxp. Then flash the firmware he wants.

kingarthas
23rd April, 2017, 07:40 AM
No need swapping any pins, he already connected, just need to erase nxp. Then flash the firmware he wants.

However i can not read mine fw. Is it normal? When flashing ECU I used to read, before write, to ensure all connections and power is good.

lsdlsd88
23rd April, 2017, 08:33 AM
No need swapping any pins, he already connected
I was sure that for serial communication TX line on interface must go to RX line on device and vice-versa....

morgano
23rd April, 2017, 10:36 AM
However i can not read mine fw. Is it normal? When flashing ECU I used to read, before write, to ensure all connections and power is good.

Yes, normal for CRPx activated in secure mcu. Cannot read, just erase.

After erase obviouly CRPx is gone and you can then read and write as you wish.

rsibiza
2nd May, 2017, 08:54 PM
Hi Folks.

I have this error after updating eeprom and FTDI.ept from my Galetto....
I hear the relay inside galetto work, but sw wont open?....447153

rhj
4th May, 2017, 01:07 PM
447558

Hello !


Can anyone confirm me on the continuity between the diode and transistor (marked in yellow lines) on the PCB galletto?


After replacing the transistor, my solder widens on the diode


Thanks

morgano
5th May, 2017, 01:27 AM
447558

Hello !


Can anyone confirm me on the continuity between the diode and transistor (marked in yellow lines) on the PCB galletto?


After replacing the transistor, my solder widens on the diode


Thanks

Remove diode, clean excess tin and see if trace goes directly to diode, then fit diode again.

XJTAG
3rd June, 2017, 06:56 AM
hello all

if this mod work in old galletto V48

thankyou in advance

rsibiza
11th June, 2017, 07:55 PM
Does anybody have the connection pinout from TTL to V54 Borad fro the LP2119?

Best regards.

p38
21st June, 2017, 09:24 PM
Which element is responsible for K-line communication?

GianniNOS
22nd June, 2017, 01:26 PM
Hi to all,
my FG Tech V54 0386, don't communicate with PCR 2.1 for remove block in writhing. Anyone know this problem and can help me?
thanks

queroseno
23rd June, 2017, 09:24 AM
Hello, I have a problem with my galletto, so far everything is fine, bdm, tricore, jtag, but now it is giving me obd problems, both by k, and by CAN, which components should I change to solve obd problem? Reads well and when he writes, he stops in half-writing or very little blocking the ecu, he has spent in several ECUs and different cars

Thanks and regards

p38
24th June, 2017, 10:12 PM
Hello, I have a problem with my galletto, so far everything is fine, bdm, tricore, jtag, but now it is giving me obd problems, both by k, and by CAN, which components should I change to solve obd problem? Reads well and when he writes, he stops in half-writing or very little blocking the ecu, he has spent in several ECUs and different cars

Thanks and regards
IMPORTANT : Is very important to get a quality USB cable. because some time K-Line didn't work because USB cable is not good

U16, U23 ----- L9637D (ST)

BWF
26th June, 2017, 09:36 PM
Does anyone have the hardware components that need to be changed in the galletto v54 Chinese?

Enviado desde mi Redmi 3 mediante Tapatalk

tango
28th June, 2017, 04:33 PM
Does anyone have the hardware components that need to be changed in the galletto v54 Chinese?

Enviado desde mi Redmi 3 mediante Tapatalk

have you even looked through this thread?

BWF
28th June, 2017, 07:38 PM
Yes, in message # 53 but I need permissions to access the file.
Find something else in message # 1151 but I do not know if it's all there is to change
http://www.digital-kaos.co.uk/forums/showthread.php/411050-Chineese-Galletto-V54/page78

moi
3rd July, 2017, 10:28 AM
460568460569so i got a fgtech vd300 v54, looks different pcb to the ones I see here, and wondering if I can use fantomels fixes for this device, as watching the mp4 how to use usb-ttl adapter ect, this pcb has nowhere to connect any jumper wires ect no holes in board like fantomels pictures, so don't know where to connect wires for rx tx gnd, and the jumper ,forgive my na?ve ignorance, and I have read this entire thread along with many others 1st, but with the pcb different from the pictures in the fix folders its thrown me a curve ball lol and confused me
can I accomplish no date change software and tool number change ect with this device??
have read via obd succesfully with the aes sotware and this tool on my Octavia mk2 edc16u1 can, although this did take 25 mins
do I just solder tx rx gnd straight to the relevant pins on LPC2119 from the usb ttl and no need jumper ???


thanks

moi
8th July, 2017, 10:46 AM
no one can advise????

morgano
8th July, 2017, 04:29 PM
You can solder to lpc legs directly, will need also jumper to enable isp mode on powerup. Just look lpc2119 datasheet all is there.

moi
9th July, 2017, 09:54 AM
You can solder to lpc legs directly, will need also jumper to enable isp mode on powerup. Just look lpc2119 datasheet all is there.
thanks, any chance of a bit more info to get it competed, so I need to solder RX TX GND, to lpc219, which pin is for jumper, and do I need to apply a power and gnd also to lpc2119, never reprogrammed a device previously so I need all the help I can get
if someone would be so kind to maybe sketch a diagram of what and where to solder to get this done would be greatly appreciated

morgano
9th July, 2017, 10:04 AM
Again, google lpc2119 datasheet and read it, all info you ask is there.

moi
9th July, 2017, 11:22 AM
well I'm no electronics wizard, so I got the datasheet in front f me now, but looking at it I'm no further forward , and I may aswell be looking at foreign language tbh, i just need to know what pins to solder which wires to on the lpc2119 from ttl-usb, not need the full specs of what the chip does ect

moi
11th July, 2017, 12:56 PM
no one willing to help with info to reprog my fgtech, please someone supply diagram of how I need to wire the usb-ttl to the lpc2119 so I can get this done, need to know which wires to which legs to accomplish this

bobolin4o
11th July, 2017, 01:21 PM
Mate, just set aside 10-20 euro and give this job to some GSM specialist near to you...
Regards!

moi
12th July, 2017, 10:38 AM
Mate, just set aside 10-20 euro and give this job to some GSM specialist near to you...
Regards!

thank for ur respone but there is no such gsm specialist near me at all


is this how i connect from usb-ttl, connecting straight to LPC2119 directly?
JUMP pin P0.14 and GND?
463601

lsdlsd88
21st July, 2017, 09:03 AM
hi

I'm trying to update my fgtech v54 from 386 to 475.

I think I did everything correctly, update lpc with pl2303, all ok.

My problem is when I open the software it shows me low voltage and buttons are not active.

with 386 software it was working fine. tried on 3 different pc, winxp/7 x32 /7 x64.

What I discovered is that if I read the eeprom with FTREADWRITE software, it will always have the same serial number in the last row.

I tried different eeprom found online, and it always write only the first part, is this correct?
see image

http://i.imgur.com/v3zfku0.jpg

Is this normal?

Marek_Spy
21st July, 2017, 09:24 AM
Hi
I have similar, someone knows the solution

fantomel
26th July, 2017, 09:39 PM
First of all, good USB cable and 2nd of all has been known that some ftdi chips are not ok, or they break. So if after you write hex to lpc and dump from ftwrite it's not working, then replace ftdi and will work.
Also said 100 times, just to be safe, try and manual install driver for interface from installed program folder (even if you interface is ok in device manager) to be 100% sure it that driver and not another installed. Make ftwrite and run program.
The one without date back in fact at run applies again ftwrite part, so if loader does not make it , you make it before run.
If still does not work change FTDI chip.

lsdlsd88
26th July, 2017, 11:33 PM
Thanks for replying but I'm totally not convinced about 2 things.

1) if i write back everything from 386 all works fine. So it seems to me a sw issue not usb or ftdi.

2) is it normal or not that ftreadwrite is not able to write last eeprom part?

About drivers of course they are from sw folder after setup.

lsdlsd88
28th July, 2017, 01:49 PM
My problem is when I open the software it shows me low voltage and buttons are not active.


In my case I did everything correctly, the solution was deadly simple.
AFTER open the program and see grey buttons, unplug and replug usb cable.
magically everything starts working -.-

to confirm, it is NORMAL that your eeprom is not completely written.

carmageddon
28th July, 2017, 02:05 PM
some tools have this problem, is not question of fw, you need always to do this sequence and work.

i rebuild one of this with all new components and MY fw and SW and same problem.

queroseno
4th August, 2017, 12:25 PM
Hi, galletto 04754 works on windows 7 64bits ?, I have problems with one that works, well in 32 bits but in 64 it does not open the program, apart from that when the program opens, I have to wait a few seconds for the relays to ring Then it opens completely and the gray protocols no longer appear

obeids
7th August, 2017, 09:51 PM
Hi.

So my FGTECH is 0386.
I read 2 or 3 ECUS with it. Should I update to the 0475? What is the difference? Is the 0475 any better? More reliable and support more ECU?
Also what hardware changes to make to the V54 FGTECH china to improve it?

Thanks alot

kingarthas
1st October, 2017, 02:13 PM
Finally some good info for 0475 EU version...

FGTECH 0475 Added New vehicle and ecu type Than 0386 Version:

11/12
OBD driver SSang-yong Del-phy DCM3.7 Read/Write, Checksum

11/12
OBD driver for Fer-rari 458 Italia MED9.6 Ecu Master and ECU Slave Read/Write, Checksum

10/12
OBD driver for Fi-at/Al-fa/Lan-cia Twi-nair/Mult-iair 8GMF and 8GSF Read/Write, Checksum

10/12
OBD driver for Ma-zda 5, Ma-zda 6 2.0 Diesel ECU RF8x Read/Write, Checksum

10/12
OBD driver for Ma-zda 5, Ma-zda 6 2.0 Diesel ECU RF7x Read/Write, Checksum

09/12
OBD driver for Sim-os 10.xx VA-G 1.2 TSI Read/Write, Checksum

09/12
OBD driver for CRD 3.xx Merc-edes 2200 CDI Read/Write, Checksum

09/12
Simos PCR2.1 VA-G 1.6 TDI Unlock Boot Tool - Read/Write EEPROM

09/12
OBD driver Sim-os PCR2.1 VA-G 1.6 TDI Read/Write, Checksum

08/12
RSA recognition Peu-geot Bip-per

08/12
RSA recognition Citr-oen Ne-mo

08/12
OBD driver Driver for writing Bo-sch EDC16C34/5 Peu-geot Bip-per Read/Write, Checksum

08/12
OBD drive Driver for writing Bo-sch EDC16C34/5 Citr-oen Ne-mo Read/Write, Checksum

07/12
OBD driver Del-phi DCM3.5 for Ta-ta Sa-fari Read/Write, Checksum

07/12
Checksum recognition for DCM3.7 Ssan-gyong

07/12
Checksum recognition for DCM3.7 Op-el and Sa-ab

07/12
Checksum recognition for DCM3.7 Ki-a and Hyu-ndai

07/12
Boot Visteon ST10F275 RX-TX Mode

07/12
Boot ME7.9.10 ST10F275 RX-TX Mode

06/12
Checksum recognition for Denso Sub-aru Tri-beca

06/12
Boot Mitsu-bishi MH7203 Hyu-ndai

06/12
Checksum recognition for Denso Nis-san L200

06/12
Checksum recognition for Denso Nis-san X-Trail

06/12
OBD driver Op-el Simtec75 CAN Read/Write, Checksum

05/12
OBD driver Pors-che SDI3 CAN Read/Write, Checksum

05/12
Cor-vette Utility CAN for change VIN, Code Align, Erase Errors

05/12
Corette Utility VPN for change VIN, Code Align, Erase Errors

05/12
OBD driver Reault SID305 CAN Read/Write, Checksum

05/12
OBD driver Masrati ME9 CAN Read/Write, Checksum

04/12
Tool Boot Hitaci Phase 3

04/12
Tool Boot Hitaci Phase 2

04/12
OBD driver Fi-at ME17.31 CAN Read/Write, Checksum

04/12
Boot Mits-ubishi for L200 MH8102F

03/12
Boot Mitsu-bishi for Lan-cer EVO MH7202

03/12
Fi-at MJ8DF CAN Serial Injectors

03/12
Fi-at MJ8DF CAN Serial Injectors

02/12
OBD driver Fi-at MJ8DF CAN Read/Write, Checksum

02/12
OBD driver Fi-at MJ8DF K-line Read/Write, Checksum

02/12
OBD driver Merc-edes Del-phi CRD2.xx CAN Read/Write, Checksum

01/12
OBD driver Fo-rd Del-phi DCM3.5 CAN Read/Write, Checksum

01/12
OBD driver PS-A Delp-hi DCM3.5 CAN Read/Write, Checksum

01/12
OBD driver VA-G Sim-os 3xx Boot mode 29F400 C167 Read/Write, Checksum

12/11
OBD driver VA-G Sim-os 9.1 Boot mode 29F400 C167 Read/Write, Checksum

12/11
OBD driver VA-G Sim-os 7.1 Boot mode 29F400 C167 Read/Write, Checksum

12/11
OBD driver VA-G Sim-os 33 K-line serial Read/Write, Checksum

12/11
OBD driver VA-G Sim-os 32 K-line serial Read/Write, Checksum

12/11
OBD driver VA-G Sim-os 3PG K-line serial Read/Write, Checksum

12/11
OBD driver VA-G Sim-os 3PE K-line serial Read/Write, Checksum

12/11
OBD driver VA-G Sim-os 3PD K-line serial Read/Write, Checksum

12/11
OBD driver VA-G Sim-os 3PC K-line serial Read/Write, Checksum

12/11
OBD driver VA-G Sim-os 3PA K-line serial Read/Write, Checksum

12/11
OBD driver VA-G Sim-os 9.1 K-line Read/Write, Checksum

11/11
JTAG MPC55xx

10/11
New password Triore Tprot V08-10

10/11
OBD driver Ren-ault Val-eo V40, Read/Write, Checksum

10/11
AUD Ren-esas

10/11
Boot Ren-esas

...

NEW for VAG SIMOS PCR2.1
NEW JTAG - BDM - MOTOROLA - FREESCALE -
NEW JTAG RENESAS
Freescale MPC 5553/5554/5565/5566 NEXSUS PORT New IAW MJD 8F2
Mair 8GMF New Delphy DCM3.5xx DCM3.7xx TRW.
Motorola Freescale MPC 555/556/561/562/563/564/565
Motorola MC 68332 - MC YQQCU - MC 68377 Trionic 5/7/8 GM-OPEL-SAAB
Motorola MC 68376 Campi 01 Lamborghini - Lotus
Motorola MC 68336 MEMS D5 ROVER
Motorola ZC 439615 - ZC 439507 IAW FIAT - VAG
New Line OBD protocols VPM GM Hummer-Corvette-Munstang-Blazer-Cadilac
New Line OBD protocols Tx - Rx Subaru - Mitsubischi - Hitachi - Denso ecu
NEW JTAG - BDM - MOT - FREESCALE :

Freescale MPC 5553/5554/5565/5566 NEXSUS PORT New IAW MJD 8F2 - Mair 8GMF
New Delphy DCM3.5xx DCM3.7xx TRW
MOT Free scale MPC 555/556/561/562/563/564/565
MOT MC 68332 - MC YQQCU - MC 68377 Trionic 5/7/8 G-OPEL-SAAB
MOT MC 68376 Campi 01 Lambogini - Lotus
MOT MC 68336 MEMS D5
MOT ZC 439615 - ZC 439507 IAW FIT - V A G
New Line OBD protocols VPM Humer-Corvette-Munstang-Blazer-Cadilac
New Line OBD protocols Tx-Rx - Sbr - Mitsubischi - Hitachi - Denso ecu
All EDC17 MED17 is good always modify with Boot Mode .



Boot Mode System:

Sak TC1766
Sak TC1767
Sak TC1792
Sak TC1796
Sak TC1797

youk
9th November, 2017, 01:54 PM
change the chip FTDI you have a fake FTDI


In my case I did everything correctly, the solution was deadly simple.
AFTER open the program and see grey buttons, unplug and replug usb cable.
magically everything starts working -.-

to confirm, it is NORMAL that your eeprom is not completely written.

Marek_Spy
9th November, 2017, 02:17 PM
OK but 0386 work OK

PaoloDigital
9th November, 2017, 02:32 PM
I update tool 475 but i have error crash , inn win7 64bit , you have solution pacth or procedure

youk
10th November, 2017, 11:27 AM
OK but 0386 work OK

the flash software the ftdi at each execution (for tool-475)

lsdlsd88
10th November, 2017, 11:36 AM
the flash software the ftdi at each execution (for tool-475)

and why this was not needed for 386? isn't possible to disable this execution?

anyway I can live with unplug/replug, not a big issue ONCE YOU KNOW you have to xD

PaoloDigital
10th November, 2017, 07:29 PM
Hello friends! I have a problem with the software "V54 for 0475 Win all." I'm with Win7 Os. Of ten attempts to start the program it runs only once. I get the following error. Can anybody help me to resolve the problem? Thanks!
424734

Hello friend i resolution this problem ,with battery monted , in laptop HP compact win7 64bit, not battery unmonted error, battery laptop monted not crash eobd2.exe .my experience.

pedroclio
1st December, 2017, 08:50 PM
merci pour le partage du logiciel

gia
1st December, 2017, 08:58 PM
Use fgtech in Notebook or netbook?

Renodiag
22nd December, 2017, 08:26 PM
So, I bought a cheap galletto on ebuy, after knowing so much about it now i think i will send this shit back. Besides, my galletto does not work either and I dont want to spend more money to upgrade this crap.Anyone can tell me which Tool I should buy? I would like to have the opinion to read other ecus like Immo, Dash, Airbag, Radio ect... thx from Germany

blackcorri
24th December, 2017, 06:19 PM
hello all

who can convert me software and hardware?
come from germany

pm to me

AVDigitale
24th December, 2017, 11:13 PM
hello i need if someone have a good and stability software for galletto v53 or v54 reworked tool thanks!

mikroel
25th December, 2017, 01:18 PM
PM if you didn't solved problem

Renodiag
25th December, 2017, 07:26 PM
My Problem is I can not read an EDC15C2 Citroen C5. Neither OBD nor Boot. Nothing happens then comes a message, send Report blabla. K-line 2x12v gnd and Bootpin to gnd everything ok. Shit. I wanted to EGR off.

Renodiag
25th December, 2017, 07:30 PM
Could it be the AC/DC adaptor that came with the v54 clone ? It took me 5 days to just get the Software running xD. Only runs on Win XP 32b SP2.

maajkii
25th December, 2017, 07:31 PM
Bro, Its Christmas go take your time with your family. :)


Wysłane z iPhone za pomocą Tapatalk

Renodiag
25th December, 2017, 07:34 PM
Haha Iam but its boring and I'm arguing with this shit cause i want to EGR off xD.

maajkii
25th December, 2017, 07:36 PM
Haha Iam but its boring and I'm arguing with this shit cause i want to EGR off xD.

This Ecu isn’t readable, find ori in web, you can flash it after by obd.
Merry Christmas, post your file I make for you egr off


Wysłane z iPhone za pomocą Tapatalk

Renodiag
25th December, 2017, 07:49 PM
Wow, where did you get that info? I've been squeezing all this crap into my head 4 a week now. How can I be sure that if I get a file file from the net that it is 100% correct for me? Thx