PDA

View Full Version : Edc15p SEAT alhambra year 2008



kenancatli
30th June, 2015, 08:10 PM
Hello
Edc15p SEAT alhambra year 2008
I can't read or write with euro clone mpps ANd euro clone gal2
via OBD !!!
help please
regards

morgano
30th June, 2015, 08:16 PM
Take out of the car, open it and read in boot mode.

kenancatli
30th June, 2015, 08:29 PM
Hello morgano

Have you guide, how do bootmode?
Regards

kevfield
30th June, 2015, 08:33 PM
Are you sure it is edc15 on a 2008 car ??? i would guess at a edc16

Thanks kev

kenancatli
30th June, 2015, 08:42 PM
Yes edc15p
I read with Bosch kts 570, I Read fault code
and Ecu ID edc15p
regards

kospoz
30th June, 2015, 09:01 PM
galletto 1260 100% read write

kenancatli
30th June, 2015, 09:24 PM
Hello kospoz
SEAT alhambra year 2008 it Is possible with Gal 1260 read write??

majkellondek
30th June, 2015, 09:55 PM
I have same problem about 6 month ago.I tryed connect to ecu thru obd using galletto 4 .
I tryed to connect about 20 times,ignition off and on.
Finally after 20 min i connected,read and write file no problem.

kenancatli
30th June, 2015, 11:05 PM
Gal4 china version?

dominik.m
1st July, 2015, 12:06 AM
ON table connect like picture!
No problem read and write gal1260 kwp2000 mpps and galletto v54

kenancatli
1st July, 2015, 09:54 PM
Hello

İgnition Fgtech cable K line it is same?

mislav88
1st July, 2015, 10:18 PM
have you tried pulling dash fuse? they still use same dashes as other golf4 type cars

kenancatli
1st July, 2015, 11:16 PM
I have no dash fuse removed,
I want do on table!
Green cable fgtech ignition is it K Line?
regards

warrio67
2nd July, 2015, 08:42 AM
green = kline
do the same pinout like dominik.m (http://www.digital-kaos.co.uk/forums/member.php/58019-dominik-m) picture
i done a sharan edc15p with fgtech this sunday
read and write fine (don't care when fgtech says turn on and off ignition) click ok

kenancatli
3rd July, 2015, 07:41 PM
Hello warrio
you read on table?
and read write slow mode?
regards

Multipla
4th July, 2015, 11:37 PM
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=321149&stc=1
This is boot mode.

Via directly is dessolder 29f400 read and decode totally or partial eeprom if you tool not function

Multipla
4th July, 2015, 11:42 PM
You can do by mpps or vairius tipe of galletto like 1250/1260 ver.48, ver.51, and so on put alimentator stabilized 12V or battery cars.

kenancatli
6th July, 2015, 05:24 PM
Hello
fgtech aes flasher Universal I think from bosnia bad tool!!!
fgtech 2 euro clone edc15p can't read and write do via obd and on table bad tool!!!
edc16c35 ?cu dead, I read via obd read ok after write ?cu dead with fgtech euro clone bad tool!!!

I do with mpps on table euro clone very good tool!!! Edc15p
regards