AVANTIME help for Pincode

[lion0304]

Hi mates
I need help for pincode from UCH dump Avantime 2001 MCU HC912DG128A, maskset 3K91D. I read with Xprog in circuit. I need programming new key because car lost all key.
VIN: VF8DEOT0624395940
Thanks
Cheers
325648

[lion0304]

No one can help me for the pincode by dump? Here is the VIN: VF8DEOT0624395940

[DottoreBL]

dump is not ok

[estate]

Should be Motorola MC68HC908AZ32/AZ60 (J35D) remove from board and read with xprog. Same UCH in these as the Espace.

[lion0304]

Should be Motorola MC68HC908AZ32/AZ60 (J35D) remove from board and read with xprog. Same UCH in these as the Espace.

It's not J35D, it is 3K91D or MC68HC912DG128A. I read several time with Xprog, all are the same dump. I'll try read with UPA later with picture from PCB.
In EFFI, the same MCU is Megane 2, Scenic 2 ID46. But this Avantime had 4D60 transponder.

[PremierD]

Comes up unknown version in TM100 ...

Edit: ... and that's in all the 912 reno programs .. I agree with the poster who said the dump is sh1t ... :)

[lion0304]

Comes up unknown version in TM100 ...

In TM100, i also see only maskset 5H55W, no has 3K91D

Edit: I'll read it again with UPA.

[PremierD]

In TM100, i also see only maskset 5H55W, no has 3K91D

Edit: I'll read it again with UPA.

Its a DG128 .. thee mask set should only apply to reading the mcu .. not reading the dump .. ( I think) ... lol

[dyzio]

325801lion writ this data on tpx2, adx or eh2
\and try start car
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=325799&stc=1

[lion0304]

325801lion writ this data on tpx2, adx or eh2
\and try start car
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=325799&stc=1

Many thank Dyzio, i'll try and report back. Good week end
Cheers

[lion0304]

Its a DG128 .. thee mask set should only apply to reading the mcu .. not reading the dump .. ( I think) ... lol

Sure, i want to say that will read the MCu with UPA if it can make diffrent than Xprog. Sorry for the confuse.

[dyzio]

Evo recognize your file with out problem so think it should work cheers now I need cold beer

[lion0304]

Evo recognize your file with out problem so think it should work cheers now I need cold beer

If one days you come to New Caledonia, i'll ive you some beers in front of the beach. Cheers

Edit: Could you give me the Pincode if possible from this dump?

[dyzio]

Sorry mate Evo don't show pin

[dyzio]

Only can make key

[lion0304]

Only can make key

No problem, your help is more than enough.

[lion0304]

325801lion writ this data on tpx2, adx or eh2
\and try start car
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=325799&stc=1

Hi Mate,
I just tested with the car, the immo light flashing with 3 transponders EH2, CN2 and YS-01 writed with your data key.
The EH2 show data with 4D60 BLANK? Crazy?

http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=325939&stc=1http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=325940&stc=1

[dyzio]

325947ok so can u try again with this data

[lion0304]

325947ok so can u try again with this data

Thanks mate, i'll report later. Does PG4 not locked may cause the imoo problem? Will test again new old key data with PG4 locked.

[kemaster]

Yes, this maight be the problem. Made such experiment before on Scenic with ID4D. If page 4 was not locked car didn't want to start.

[lion0304]

Thank you Dyzio for your help but i can't make running the car.
Customer take pincode from dealer and after try all data key you gave, light still flashing. So i try programme the key by Canclip with blank 4d60 carbon.
After insert the blank key, i need turn off ignition and press the remote to close the prgramming.
Problem is i have no remote, so the process is not finish and immo light still flashing.
I try to do the same programming with your transponder data key without succes.
Now give up the car to dealer. here is the data key i programmed by OBD with 4d60 blank
http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=326246&stc=1