PDA

View Full Version : dtc remove simos 9.1



kospoz
10th October, 2015, 01:29 PM
Hello everybody i read this ecu simos 9.1 with Kessv2 in 40 seconds i think the file is ok.Can someone remove two faults? 16524 P0140, 16520 P0136.
The sensor has been replaced with oem the wiring is fine but the fault is here.
Thank you

bobolin4o
10th October, 2015, 01:41 PM
Is this full file?
I think is partial read... for erasing DTCs, you need to have full.
Regards!

kospoz
10th October, 2015, 01:46 PM
Is this full file?
I think is partial read... for erasing DTCs, you need to have full.
Regards!
And how can i read the full file?Maybe galletto can?

bobolin4o
10th October, 2015, 01:49 PM
look, i'm not 100% sure about this...
Wait a while for someone else.
But if i'm right, that must be a full read, you can read full in boot mode.
Regards!

mihaiservice
10th October, 2015, 01:53 PM
Hi
file are full read 100%

kospoz
10th October, 2015, 01:55 PM
Hi
file are full read 100%
can you delete the codes?

bobolin4o
10th October, 2015, 01:59 PM
Hi
file are full read 100%

Hm... and why is so empty...
Here is file from a Simos 3 for example, readed with programmer.
Maybe the Germans made Simos 9.1 with "compressed" software...
Regards!

kospoz
10th October, 2015, 02:09 PM
strange....

kospoz
10th October, 2015, 07:02 PM
tomorrow I will read it by bootmode with galletto and I will upload the file

kospoz
11th October, 2015, 11:33 AM
here is with bootmode bobolin4o had right is different can somebody now help?

bobolin4o
12th October, 2015, 06:54 AM
here is with bootmode bobolin4o had right is different can somebody now help?

First of all - never touched such ECU...
Here is the file, i think is good, but who knows... If you want to try it, flash it in boot mode!

kospoz
12th October, 2015, 05:27 PM
First of all - never touched such ECU...
Here is the file, i think is good, but who knows... If you want to try it, flash it in boot mode!
The file is working good. bobo you have right about the fault 0000 but the mill is off no problem thanks again :congrats:

bobolin4o
12th October, 2015, 05:31 PM
Not so bad for first shot, yeah...
Thanks for the report!
Cheers!

tomtom0785
19th May, 2016, 02:24 PM
376428hello - MAybe someone can help me here,....

i got stuck when trying to deacitvate the 2 fault codes
fault table is from adress 522D6 - 53245

no matter what i try - i cannot deactivate any fault code ( set to Zero or FF doesn't success )

original file is attached

thanks in advance
regards Tom

bobolin4o
19th May, 2016, 02:35 PM
When set values to zero you must have P0000...
Which DTCs you have?

tomtom0785
19th May, 2016, 02:43 PM
hi, i have DTC P0420 and DTC P1544

yes Setting values to Zero is correct - then i receive P0000 - fault reserved by iso - but i don't think fault code is really disabled in this case, or am i wrong??
means i think MIL still Comes up, or doesn't it?? have you tested this?

bobolin4o
19th May, 2016, 02:52 PM
hi, i have DTC P0420 and DTC P1544

yes Setting values to Zero is correct - then i receive P0000 - fault reserved by iso - but i don't think fault code is really disabled in this case, or am i wrong??
means i think MIL still Comes up, or doesn't it?? have you tested this?

MIL must be off, DTCs must be 2 P0000...

Without a Damos is almost impossible to deactivate DTCs properly, so...


Mmmmm, P1544 is not for masking, there is problem with e-gas!!!

tomtom0785
19th May, 2016, 03:31 PM
ok i will give it a try and post result - thanks man!!

tomtom0785
23rd May, 2016, 10:10 AM
hi,

after a 150km driving cycles seems to be ok - in Memory is P0000 stored, but MIL stays off - thanks boblin4o

dadal
12th November, 2017, 03:48 AM
First of all - never touched such ECU...Here is the file, i think is good, but who knows... If you want to try it, flash it in boot mode!Hi Bobolin4o,
I have same ecu from Polo 1.2 yr2007 with partnumbers : 03D906023B , this ecu is from an crash car and has DTC stored : 18017 P1609 Crash Shut-Down Activated ,
I cant remove this DTC ( on bench) because I do lose communication with ecu after five seconds..( ecu turn itself off, )
.I have read this topic and ecu flashed with an dump of 29F400 from other simos9.1 , but I have still same DTC ,, if I write 93c86 with dump from other simos( after made immo off)
then no P1609, but then I get immo problem, engine blocked, I m sure that my immo off file is 100% OK..
( 01 - Engine > Adaptation - 10 > Channel 91 shows 1 = immo off) but I have still immo problem..I thought DTC are stored in 29f400,,
I wanted to ask your opinion,,what can I do in this caseThanks for your time

bobolin4o
13th November, 2017, 07:12 AM
look at this...
http://wiki.ross-tech.com/wiki/index.php/18017/P1609/005641

dadal
13th November, 2017, 01:45 PM
Hi Bobolin4o,

I did this step before I sended this message, info on rosstech has not helped, I tried also to edit 93c86 manually, but then I get checksum fault.
I will search dumb set ( 29f400 + 93c86) from other simos 9.1
thanks for you time and interest