View Full Version : BMW X1 FRM3R 6135-9224592
mb232
6th November, 2015, 12:50 AM
Hi , i need eeprom MC9S12XEQ384 for modul FRM3R 6135-9224592 BMW X1 2009r.
please help me
Thanks
nogger1
5th April, 2016, 07:36 PM
It's an old thread but i am also lookng for the same eeprom dump, can anyone help ?
TIA
Nogger1
vasko
9th April, 2016, 11:59 AM
Before 1 months i have problem x1 2010 or 2011...my board burned...i change genuine processor to second hand board and job done ... This is genuine boxhttp://uploads.tapatalk-cdn.com/20160409/645466bcc09d0ce32edcd35febdcb3bc.jpg
Sent from my iPhone using Tapatalk
vasko
9th April, 2016, 12:03 PM
Now this processor on picture from second hand board...i sure second board other numbers but not remember...
Sent from my iPhone using Tapatalk
vasko
9th April, 2016, 12:05 PM
Numbers of second hand it was different
Sent from my iPhone using Tapatalk
vasko
9th April, 2016, 12:06 PM
If need to try i will read this and post
Sent from my iPhone using Tapatalk
nogger1
9th April, 2016, 08:51 PM
Excellent, a dump would be appreciated
Nogger1
vasko
11th April, 2016, 12:59 PM
can you tell me how to read this processor....
I have etl but not support this mask
upa read this...?
nogger1
13th April, 2016, 07:57 PM
i used XProg v5.55 , only 4 wires. I think UPA can read but i dont have connections,
vasko
14th April, 2016, 04:03 AM
Can you send me photo
Sent from my iPhone using Tapatalk
vanos batam
14th April, 2016, 01:03 PM
You can use any eeprom from good FRM3..
After you have to Write VIN and flash by WINkfp. Read VO from Cas the write it to FRM.
It work 100%
vasko
3rd May, 2016, 07:16 AM
this is all from processor ...eeprom p-flash d-flash ...
folarinm
4th May, 2016, 12:28 AM
Sent from my E7 using Tapatalk
nogger1
4th May, 2016, 09:16 PM
Thanks Vasko , i will give it a try
Nogger1
ykizak
12th May, 2016, 12:50 PM
I got the same module for an E87 problem is i am getting all 00 when i reed the EEPROM section anyone has an idea why?
I know its an old post bot hoping someone knows why.
Edit: I am using UPA to read it and i can read p-flash but i cannot read EEPROM
6135-9224592 with 9S12XEQ384 - 3M25J Mask
Regards
omarabeid
17th May, 2016, 02:01 AM
wiring diagram MC9S12XEQ384http://www.e90post.com/forums/attachment.php?attachmentid=1308279&stc=1&d=1445981196
ykizak
19th May, 2016, 10:00 AM
Problem with mine was the fact that partitions were gone. So i had to recreate them. I am able to program it now. However i cannot find a matching dump.
Pali33
31st October, 2016, 11:01 AM
hi, i have the same problem, i read eeprom all 00.
Please how to recreate the partitions with UPA? Which settings?
thanks
juanes 3
13th November, 2016, 01:04 AM
programmers to read flahs i Epron Epron and R270 read i i flahs writes hope this tip helps
centrohifi
10th February, 2017, 10:48 AM
I, as UPA-S is set to read EEP Emulated ? solutions ?
to find, information :(
FARFAN86
25th April, 2018, 05:55 AM
I have used the Xprog many times to extract EEE I have never had problems
doanlinh
26th April, 2018, 11:18 AM
http://tlvps.tomvanleeuwen.nl/frm/
assitutto
20th September, 2018, 09:25 AM
this is old post but eeprom partition is 16*256
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.