PLEASE HELP ON BMW E60

[aketokediag]

Hello M8,
I have issue on CAS2 chassis number WBANC710X0B157390 E60 i made key to this vehicle through TAGPROGRAMMER and the car didnt start. I read a post here that talk about downgrading of CAS dump. Questions are am i to downgrade the dump? how can i downgrade it? what is the possible solution to start this car? here is the vehicle dump.

[vanos batam]

What problem exactly
lost all key or add key?
which tool use programming the Cas?
did you manage to diagnossis and comonication with the Cas??
post dump and key dump

[autochei]

u need make sincro dde-cas
e 60 no need to downgrade

[aketokediag]

What problem exactly
lost all key or add key?
which tool use programming the Cas?
did you manage to diagnossis and comonication with the Cas??
post dump and key dump

Thanks m8, this is all key lost condition, also i dont have key dump but have post CAS dump, I use AK300 to read the dump and i used AVDI+TAGProgrammer to write on ID46 chip PCF7936
Thanks

[aketokediag]

u need make sincro dde-cas
e 60 no need to downgrade
Please M8, how did you mean I need to make sincro dde-car? Please put me through am very new to BMW key programming
Thanks
Ak

[rivalryan]

Did you prepare/config of Hitag (7936) prior to programming? if not it will not work

[aketokediag]

Did you prepare/config of Hitag (7936) prior to programming? if not it will not work

Thanks M8,
I didnt prepare/config of Hitag please how can i do this as i told you earlier am very new to BMW key programming, please i need step by step to make this car start.
Regards
AK

[rivalryan]

Did the transponder learn into the slot you selected or not? if it did you should have a picture of the ELV on the dash, if so go to CAS 40 and select sync (CAS & EVL) and job is done.

[bearheroes]

Did you prepare/config of Hitag (7936) prior to programming? if not it will not work
Please advise me...What preparation is needed?
Is any special proccedure?

[cjawahir]

VIN: WBANC710X0B151384
DME Code: 000062EA
Odometer: 160047 km
Key Type: E60 old type
Mechanical Code: 1905
Remote Frequency: 868MHz

thats the info from the dump u post , the chassis number is diffrent from what u post , so maybe some one change the dump or cas ?

cj

[aketokediag]

Did the transponder learn into the slot you selected or not? if it did you should have a picture of the ELV on the dash, if so go to CAS 40 and select sync (CAS & EVL) and job is done.
Hello M8,
Transponder has been learned on key number 4, please what tool is the best to make this job done??
Regards
AK

[rivalryan]

Did the transponder learn into the slot you selected or not? if it did you should have a picture of the ELV on the dash, if so go to CAS 40 and select sync (CAS & EVL) and job is done.


Please advise me...What preparation is needed?
Is any special proccedure?

preperation is required to learn pcf 7936 in ignition

[bearheroes]

preperation is required to learn pcf 7936 in ignition
ok tell what is the proceedure.

[rivalryan]

Change first byte on config page from 06 to 0E. Also change second digit on user page 0 to a 2 e.g. G823456 becomes G223456

[bearheroes]

Change first byte on config page from 06 to 0E. Also change second digit on user page 0 to a 2 e.g. G823456 becomes G223456

You probably don't know what you are talking about and maybe never have worked on bmw and hitag also...
ID(Page0) CANNOT change.
Does NOT need any configuration on config byte.
So please DON'T tell whatever you want.

[rivalryan]

haha either you can't read or you haven't a clue. User page is not the same as Identifier you need to check before you make such stupid comments!

that procedure is 100% correct to learn 7936 in ignition, this is not needed if you use tag tool to write 7936 hence why I said in ignition but you probably didn't read that bit correctly either.

[Johnner]

Guys,stop with the pissing contest please !!

Thank you...

[aketokediag]

haha either you can't read or you haven't a clue. User page is not the same as Identifier you need to check before you make such stupid comments!

that procedure is 100% correct to learn 7936 in ignition, this is not needed if you use tag tool to write 7936 hence why I said in ignition but you probably didn't read that bit correctly either.

Please M8,
so far you done it and it works for you please kindly give me step by step to make this car start,as you can see have already prepared the 7936 through AVDI+TAGProgrammer, also can i make use of Used EML chip. i have used EML that was used on EWS 3, Please help me to sort this car.
Thanks in advance

[aketokediag]

VIN: WBANC710X0B151384
DME Code: 000062EA
Odometer: 160047 km
Key Type: E60 old type
Mechanical Code: 1905
Remote Frequency: 868MHz

thats the info from the dump u post , the chassis number is diffrent from what u post , so maybe some one change the dump or cas ?

cj

I didn't think anyone change the CAS, it seems I didn't get the VIN number correctly, please kindly help me sort this car, can I use my AVDI to do synchronization? Please put me through.
Regards
AK.

[aketokediag]

Thanks to everyone that contributed to this topic I appreciate everyone of u.
Problem solved.