KTAG and SID208

[wiseman]

Had a SID208 from 2014 transit custom today on bench for hours.

would connect read and stop and 7%

Tried various voltages, all above 13.8v to 14.4v

Also tried, TRASDATA sw and same happened at 7% exactly.

Anyone else had this?

[waldi1979]

I read (boot mode) this ECU by X17 - no prolem.
Write - by OBD.

[robert54]

Your Clone is Low Quality-Euro clone read and write no problem.

[neuro]

I can confirm what robert54 said, done defender 2013 with 2.2 transit engine sid208 using ktag 2.11 and write by obd using kess 2.08 both pcb not reworked just changed nxp chip.

[wiseman]

I've changed NXP in my ktag. I think maybe xtal maybe wrong MHz

[furburger]

Clone Ktag ( reworked) worked fine for me also...

Sent from my SM-G900F using Tapatalk

[jnoroeste]

M8,
Maybe not a problem about volts, but amps!!
Only trust on genuine tools to work with those ecus .

Regards.

[furburger]

More that 3amps drawn when pass is read I think..

Sent from my SM-G900F using Tapatalk

[wiseman]

More that 3amps drawn when pass is read I think..

Sent from my SM-G900F using Tapatalk

I had a supply that could support 12 amps attached. I watched the amps getting drawn on the read and it never passed over 1. Used an orig Ktag was fine. I think the oscillator for MCU clock speed while talking to tricore is not giving a stable signal. Maybe a sector at 7% requires a high duty cycle from the tool

[ernene]

Conect to a car battery. I have same problem with a 807 evolution and solve with a 70ah battery

[pinotec]

I had a supply that could support 12 amps attached. I watched the amps getting drawn on the read and it never passed over 1. Used an orig Ktag was fine. I think the oscillator for MCU clock speed while talking to tricore is not giving a stable signal. Maybe a sector at 7% requires a high duty cycle from the tool
your problem is crystal not murata
for fix or change crystal with murata version or add capacitors 22pf
crystal murata does not need capacitors

[overs0ull]

Your problem is that you need 10amp and 14v and will read it perfrct

[robert54]

My power supply is 5A and voltage 13 and read 100%

[teamtuner]

Your problem is that you need 10amp and 14v and will read it perfrct
agree with you...

[wiseman]

Your problem is that you need 10amp and 14v and will read it perfrct

Maybe it has solved for people before, I tried many many voltages from 13.8 all the way up to 14.4, with a min of 12 amps, I also tried migrating the tool to tradata SW and the same fault stops at 7%.

[morgano]

You have quartz or resonator? Pinotec gave you good clue. Believe him.

[javyb]

your problem is crystal not murata
for fix or change crystal with murata version or add capacitors 22pf
crystal murata does not need capacitors
What mhz does the murata oscillator need to be

Thanks

[CustomCars]

What mhz does the murata oscillator need to be

Thanks

8Mhz use bes quality one

[javyb]

8Mhz use bes quality one
Struggling to find a 6 pin smd murat oscillator with 8mhz

[CustomCars]

Struggling to find a 6 pin smd murat oscillator with 8mhz

use 2 pins will be fine :)

[morgano]

Here you can find the good one

http://uk.farnell.com/murata/cstce8m00g52-r0/resonator-ceramic-8mhz-smd/dp/2443268

[gazvts]

get them rs component javyb free post

[javyb]

Sorted ordered from rs same part number as given by Morgano

[parik]

I have from user CustomCars reworked Ktag, but reading fall down in 47% with power 14.45V, some idea?

[wiseman]

I have from user CustomCars reworked Ktag, but reading fall down in 47% with power 14.45V, some idea?

How many amps does your power supply give out ?

[CustomCars]

Propably supply power. Ecu will be don't readed correctly even at 15V and 2Amps.
13,5V is ok, but needed provide lot Amps, can use car battery for power supply if lab tools are not from top.

[Faraday]

I have same problem it goes to 50% and error

[parik]

i used profi charger (10a) with conected batery 95ah and voltmeter showed 14.45v a charger between 2-3a. can i try 15v?

[CustomCars]

Nope, voltage 14 is enough.
Maybe have backup stock quartz clock ? try fit to check.

[parik]

please, check, this is sid807evo, but some problem like sid208

359372359373

[CustomCars]

Try stock quartz clock if have, but should be good...
Other possibility is change protocol on it. Soon i post here files to check.

[parik]

i will try

[parik]

with china quartz clock DONE !

[CustomCars]

Possible, some time it cause problem. That's why always needed have both.
Reworked have best available quality guarante max stability, but some parameters are different, and mcu makes problem.

[teerak2uk]

13.8v 3amp and mine reads fine

[parik]

yes, i read out 1.1mb dump, there is corected? does need quartz clock some orientation on dashboard? and what about edc17cp66 with firmare v6.070?

[parik]

CustomCars send me slave tool :(((((((((((

[CustomCars]

EDC17CP58 highest version support
EDC17C79

Orientation of quartz no matter.
Post file to check.

[parik]

sorry, mercedes car have edc17c66 but in trastada nothing in menu:(
i payed to CustomCars for rework and upgrade firmware for KESS v4.036, i think i got from him fake firmware, becuase i get internal error if i try select SID208 in menu.

[CustomCars]

What you talking about ? Really incomprehensible posts.
Any error in SW comes from SW, internal error make bad installed software.

[parik]

thanks for great support for customcars, now only litle problem with checksum error in ktag and kess for ecus sid807 and sid208.

[milanocito]

read/write it with katg china clone work 100%

[parik]

windows xp or 7, 32bit or 64bit? Only microsoft redistributable 2005? thx


read/write it with katg china clone work 100%

[Gibek]

Ktag read fine, 12.5V 3amp supply, You have problem with your tool, need it more stable. Mine slows at 7% too, but goes on

[parik]

i think problem is some missing dll from ms redistributable for checksum caluclation under win7?


windows xp or 7, 32bit or 64bit? Only microsoft redistributable 2005? thx