PDA

View Full Version : MC68HC05B32 - Big problem - Scenic UCH



LucasDChaos
11th January, 2016, 10:20 PM
Hello guys,i have very wierd problem with this mcu(Scenic 1.9 dti 99'). I desolder chip from faulty uch and cloned it with xprog-m to another uch.Now after soldering them back to those two units they stoped to work.Nothing ,no immo led central locking etc. I understand that something could be wrond with that one witch was programed,but first one was just readed and solder back.Have you guys had same problems with renault uch? I was desoldering it using hot-air.Any clues? Cheers

kiszka
12th January, 2016, 12:07 AM
...............

LucasDChaos
12th January, 2016, 07:35 AM
But why that first one stopped to work only after reading and soldering? I'm wondering what was the reason...

antwnhszr
12th January, 2016, 08:29 AM
your xprog-m don't read well the mcu with result now you have this situation.....now you have lost all the data from your car and the one thing do you make is only immo off....
regard's

LucasDChaos
12th January, 2016, 08:35 AM
Ok i managed to start original uch to work(faulty resistor after soldering :( ).Problem with this unit is no led blibking and immo dont recognize keys.I will try to make the second one reprogram again.

antwnhszr
12th January, 2016, 08:38 AM
put the mcu from uch car without any modification on uch donor....and start your car

LucasDChaos
12th January, 2016, 12:45 PM
Mcu switched into donor uch - the same problem. No immo led,wrong key code,sometime showing antena power fault. So it looks like problem with dump inside motorola... :(

rokibar
12th January, 2016, 01:10 PM
put here dumps and will know is problem there

gokart
12th January, 2016, 07:20 PM
MCU is faulty therefore the dump is incorrect.

elephantul
12th January, 2016, 07:41 PM
original dump is faulty, i have exact same trouble, solved by put another uch, make new transponder, virginize engine ecu

lion0304
13th January, 2016, 01:23 AM
I have 3 cases these Megane, Scenic 1PH2 without immo light.
All these case came when client lost all key 4D60. Renault tried recode with ID46 inside and UCH dump corrupted.
My first case solved: replace new used UCH like elephantul said (new key from uch, virgin ECU EMS3132)
Seconde case: Found used ECU + UCH + key EMS3132
And the last: Virgine Sirius 32 + emulator.
Also can put inside virgin UCH dump and recode with Clip (not tested yet)
351467

LucasDChaos
13th January, 2016, 01:51 PM
Here is dump from Uch
351543
What you guys think?

rokibar
13th January, 2016, 03:14 PM
pin code: 67326425 transponder 4E
all keys eresed. if have key data put tham here maybe halp

lion0304
13th January, 2016, 10:23 PM
Just done another yesteday.
First i think replace by used new UCH (ihave one), make key and virgin Sirius 32.
But it take many time, so i virgin ECU, put in sirius immo emulator.
Car start the first time key turn.

LucasDChaos
13th January, 2016, 10:30 PM
Thanks rokibar your pin code is correct.But no key data so i'm gonna cut immo in ecu.Is there option to get 4 digit pin number from uch dump?

adusia123
14th January, 2016, 12:25 AM
MEGANE / SCENIC UCH UNDER THE INFLUENCE OF LOW TEMPERATURE CHANGES CONFIGURATION TYPE 1 TO TYPE 2 OR with the 2 IN TYPE 1 ERROR IS ENOUGH DISH RECEIVER clip configure AND IS OK:stung:

gokart
14th January, 2016, 01:33 PM
This system uses 8 digit pin code. It's different from the 4 digit systems.

gokart
14th January, 2016, 01:35 PM
@adusia123 (http://www.digital-kaos.co.uk/forums/member.php/95947-adusia123)
It's only a temporary solution.

LucasDChaos
14th January, 2016, 08:53 PM
After immo off in ecu car is running ok again.

thanosxx
13th May, 2016, 03:28 PM
I have the same problem of Renault megane ,desolder the mcu of uch ,read with xprog(original) solder back ,and nothing work ,immo,central locking,wiper,do you found a solution?

kiszka
13th May, 2016, 06:58 PM
is Original transponder:
Tiris DST 4D (ID60)
Tiris DST 4E (ID64)
Allowed transponders:
Tiris DST 4D
Tiris 4E
Pin Code - 67 32 64 25