2012 FORD FIESTA ANYONE PLEASE HAVE A WIRING DIAGRAM TO CONNECT THIS WITH R270

[Thos]

Hi,
Can I programme this ford fiesta with r270 programmer??
I tried with digimaster3 but when it reads the mileage it says 524344km but it actually
has around 323849km and when I enter a new mileage it cannot write to dump just says
error after about a minute .
Also tried with digiprog3 4.85 - 4.88 but will not read by obd.
Digital odo display is red on this one not blue.
Any info greatly appreciated

Thos

[pintu]

this pinout for upa usb may be this helpful to you352161

[XmoDDeR]

524344km is 325827 miles things that make you go hmmmmmmmmmm

[Thos]

this pinout for upa usb may be this helpful to you352161

Hi
thanks fir that will give it abtry in the morning and see how I go

cheers
Thos

[Thos]

524344km is 325827 miles things that make you go hmmmmmmmmmm

Ah yes that is interesting good call ,

thanks

Thos

[diagtech]

Should go with digi with red display

[Thos]

this pinout for upa usb may be this helpful to you352161

Hi
No luck connecting it with r270
using this wiring

Thos

[XmoDDeR]

DONT USE R270

[Thos]

[QUOTE=XmoDDeR;2685517]DONT USE R270[/QUOTEWhat you recommend I use ?

[XmoDDeR]

I would just use UPA , or find something in digiprog thats same algo solder wires read away match edit .......happy days

[XmoDDeR]

try digi 4.94 or again with old doors closed , try a other can car obd and see if it works if not digi wiggy issues

[norman1967]

Hi,
Can I programme this ford fiesta with r270 programmer??
I tried with digimaster3 but when it reads the mileage it says 524344km but it actually
has around 323849km and when I enter a new mileage it cannot write to dump just says
error after about a minute .
Also tried with digiprog3 4.85 - 4.88 but will not read by obd.
Digital odo display is red on this one not blue.
Any info greatly appreciated

Thos

Hello. Is this out of a st? Can I see photo of sticker on rear?

[Thos]

Hello. Is this out of a st? Can I see photo of sticker on rear?

Hi,
Here is the sticker on back of cluster which I presume is what you mean
as on back of car there is no badges (must have been removed????)

Thos

[Thos]

Hi,
Tried connecting as per digiprog instructions both ways back o board and inside of board

next to mcu but says error!!!! tried on focus,Mondeo,c-max, all say error.

any ideas anyone.

Thos352257

[jakesman]

if i can remember correctly i did this same dash with x-prog and did the millage correction with Tachosoft_23.1 and hex editor , all was good

[XmoDDeR]

Hi,
Tried connecting as per digiprog instructions both ways back o board and inside of board

next to mcu but says error!!!! tried on focus,Mondeo,c-max, all say error.

any ideas anyone.

Thos352257

use the rear points as i dont think the BDM pads are active , well it looks like they are not, i could be wrong its early here vision blurry and cant find my oxygen

[XmoDDeR]

352278

TRY THIS , WORKING WITH YA MATE . GOOD LUCK

[norman1967]

Hello again. This must be a December 2012 model then. Digi cannot do them this late by obd. Smok can do these obd

[Thos]

352278


TRY THIS , WORKING WITH YA MATE . GOOD LUCK

Hi,
Connected with r270 it goes to read for a few seconds all looks promising until it then says unknown mcu ?
mask 3l16Y for this mcu but r270 does not have this mask
any ideas ??

Thanks

Thos

[XmoDDeR]

idea is last time DONT USE R270

no thanks all the instructions i daum near did car for u



thanks

[zckariya70]

Up to 2008 to 2009 Fiesta only digipro can do , after 2009 Fiesta cannot do with digipro it will always say unknown version or unknown mcu , In this case UPA _ USB is best never fails for me in any odo ,

[Thos]

Hi,
Regarding purchasing UPA programmer should I just purchase latest version from any china seller ???
Is there anything to look out for ?? Any recommendations for sellers ??

Thanks again everyone.

Thos

[zckariya70]

always buy orginal

[Thos]

always buy orginal

Hi,
Can you recommend seller ?

Thos

[frankrayk]

http://www.elrasoft.com/

[albertros]

Hi,
Feedback

managed to do mine thanks to this thread.
Used xmodder wiring diagram, Genuine car prog/mcu/motorola/hc12/3L16Y setting / A10 adapt with red-brown-blue-grey wires. and tachosoft 23.1 converting miles to km on iphone app.

[byuri]

hi thos
use the digiprog in obd , works 100%

[jjservice]

here is your wiring connection using digiprog3 clone using PLUG48,,,, hope this can help....or you can use also UPA and other reader devices on this...



430606