View Full Version : Digiprog - programming Santa Fe 2008 dash
bluefen
17th January, 2016, 07:15 PM
Could you help me, how to make correction on my oddometer on my Santa fe 2008. I have digiprog v3.94, but there is two models santa fe. When i try to connect, the error is "Chip not found"
Thank you in advance
PremierD
17th January, 2016, 07:46 PM
Then choose the other model mate ...:)
bluefen
17th January, 2016, 07:56 PM
Then choose the other model mate ...:)
I try with all available but without result
XmoDDeR
17th January, 2016, 08:06 PM
2008 should be a 93c46 wats the issue send a picture of what you are doing ive done them before with that tool no issues, unless u have the wrong chip or your clip is bad.
bluefen
17th January, 2016, 09:08 PM
352349352350352351352352352353
2008 should be a 93c46 wats the issue send a picture of what you are doing ive done them before with that tool no issues, unless u have the wrong chip or your clip is bad.
The dash working perfect on the car, but i'm not sure that digiprog support it. i try many times but without result - chip not found
PremierD
17th January, 2016, 09:23 PM
desolder the eeprom from the board mate ...
bluefen
17th January, 2016, 09:27 PM
Why ?
Problem with chip or not support by digiprog ?
PremierD
17th January, 2016, 09:29 PM
The chip will be supported ... but not on the board .... just try and you will see :)
XmoDDeR
18th January, 2016, 12:38 AM
its also obvious that ur clipped onto the chip backwards if u look red trace, to the left of it pins 6 and 8 joined ..............hmm turn clip around . My 2 cents
XmoDDeR
18th January, 2016, 12:43 AM
desolder the eeprom from the board mate ...
Hey PD that would work for him too if he knew where pin 1 was ...........................:roflmao:
vrsc
18th January, 2016, 12:55 AM
Hello, is your Testclip o.k. ??? Original is:
1 8 2 7 3 6 4 5
vrsc
XmoDDeR
18th January, 2016, 12:59 AM
Hello, is your Testclip o.k. ??? Original is:
1 8 2 7 3 6 4 5
vrsc
original is :
ST 1 clip
DB25 blue clip
1 1
2 2
3 3
4 4
19 5
6 6
5 7
7 8
XmoDDeR
18th January, 2016, 02:10 AM
352371
visual aid, hope ths makes things clear
ibratex
18th January, 2016, 02:20 AM
i did this dash last week with clip onboard , just make sure you are not joining any of eprom legs while reading by clip
proaudio420
18th January, 2016, 02:47 AM
Ive done plenty of them if your getting chip not found your more then likely have the clip on backwards otherwise you have a broken wire to pin solder on connector
bluefen
18th January, 2016, 09:06 AM
352371
visual aid, hope ths makes things clear
Thank you.
I will check the cable pinout. I saw in digiprog instruction that C46 is old santa fe's dashboard. May be the new one is not supported.
PremierD
18th January, 2016, 09:59 AM
I try with all available but without result
In light of recent information coming to light mate ...........turn the clip 180 degrees you plank .:roflmao:
rtbdiagnostic
18th January, 2016, 01:05 PM
Your dash is the 93c66 eeprom - desolder and read - save bin file - then post the file -
Tadas chipDPF
18th January, 2016, 08:56 PM
desolder, digi support it, u mast solder eeprom on adapter 1, cos with these clips is bad connection
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.