Ford Focus BDM needed Bosch edc16 0281012487

[pulsar2000]

any one kindly help im looking good BDM Ford Focus 1.6 tdci
BDM needed Bosch edc16 0281012487

Flash and 8kb eeprom please.
have a issue where pcm failed update on IDS, bad china Clone, :<
now car not start, we seem to have good eeprom data, and flashed supposed good bdm
but still no start, no immo codes on DTC tho which is strange,
No crank tho.
we think just flash touched / erased with ids,
anyone suggestions,
Cheers.

[pulsar2000]

on dash red led lights, and engine error / malfunction on dash written,
with ign on,

[carmageddon]

how many hp have this car?
write sw number (is not present on label, need to have file)

[pulsar2000]

1039s20135 correct ?

im not sure if 90 or 110bhp.

2007 car

im sure says check engine or similar on dash, and red led

[pulsar2000]

possible to immo off this ecu ?

[carmageddon]

1039s20135 correct ?

im not sure if 90 or 110bhp.

2007 car

im sure says check engine or similar on dash, and red led

i wrote that SW number are not present on label!

need to have file and hp

[carmageddon]

possible to immo off this ecu ?

i try many pro solution and never worked immo off

[pulsar2000]

i get info now,

[pulsar2000]

sw 1037386031
Think 110bhp as has dpf filter...
cheers

[mihaiservice]

Hi
upload original flash and eep,i will try to repair the file !

[pulsar2000]

i can upload later, i already wrote back supposed good bdm dump, assuming eeprom ok,
and same result, unless eeprom area is not ok,
i upload soon,,,

[pulsar2000]

ok here is reads,
Bdm after failed ids PCM update, should be flash empty, eeprom ok

Then we have recovered, this is when i write supposed good BDM backup flash, eeprom should be same as orig,

Then i have alternative flash, someone didnt like good bdm as seemed to think maps offset, so i try this,

all no good, as car not start,

[pulsar2000]

i write bdm using cmd1255 as k tag wouldnt allow me to write flash,
i write alternative using k tag,

[pulsar2000]

1037386031:C40283B_
05.03.2004[F_SB_SO.3.2]
BOSCH EDC16C34/2.20/2.
C562/RevC C

original ecu id, before we use IDS, and car was ok,
also original OBD read via Fgtech,

[pulsar2000]

its possible we lost key programming,
im sure was asked if car had pats when we do pcm update, i had no idea what was ,,,,
u think key lost ? or would i have a DTC for key lost prog ?
anyone

[pulsar2000]

Bump....
Anyone help ?
advise please

[mihaiservice]

Hi
your request sir ! the car must be ok with these file !

[pulsar2000]

Hi
your request sir ! the car must be ok with these file !

Thank you i try now, u see issues with Dumps i posted ?
like to know why u think will be ok now,

Cheers and thanks .

p.s added u on skype

[pulsar2000]

Hi
your request sir ! the car must be ok with these file !

Thank you so much, yes car start fine your file, can you tell me did you adjust eeprom area or flash or both ?
i had 2 other look at same project and no start, there soloution,

very pleased, well done

[pulsar2000]

Still have this fault,
P1187 - Variant Selection
- Intermittent

i believe corrupt sw, so ids PCM update still required,

[mihaiservice]

If are intermitent you can disable that dtc ! no limp mode !

[silvergl]

Hi,
please send eeprom . thx

[pulsar2000]

If are intermitent you can disable that dtc ! no limp mode !

you can make with dtc gone ?
yes intermittent,
did you mod eeprom ? when you made me good back up or just flash ?

[pulsar2000]

Hi,
please send eeprom . thx

eeprom is posted in focus rar on page 1

[mihaiservice]

Hi
here you have file with P1187 disable !you can write via OBD !

[pulsar2000]

Hi
here you have file with P1187 disable !you can write via OBD !

Thanks

Big ask, as well as p1187, we also need egr off,
codes we also have
p2141
p0380
p0487
p0438
p0488

be really nice if you can ammend dump so i can try, i added you on skype today,,,,

[pulsar2000]

Hi
here you have file with P1187 disable !you can write via OBD !

will this stop message "Check engine" on dash screen

[mihaiservice]

hi
this file will stop that message from cluster !
disconnect the plug from egr also differential pressure sensor from dpf !

[pulsar2000]

hi
this file will stop that message from cluster !
disconnect the plug from egr also differential pressure sensor from dpf !

Hi this mod car dont start, today i updated pcm with ids, and now variant code gone, clear,
we just have 2 dtc now, p0380 and p0487 need removal, Please,
here is good obd read, as car is now,
i thank you in advance, you have been very helpful,

[mihaiservice]

Hi
P0380 are from glow plug module !you have to fix it !

[pulsar2000]

Hi
P0380 are from glow plug module !you have to fix it !

Not poss to code out this ??

ok can you code out p0487 ? please

[CustomCars]

Done friend.

[silvergl]

361215

write this file BDM.

ciao

[pulsar2000]

Done friend.

just to clarify we do PCM update with ids *Success to clear Variant Code issue, 1187 or whatever, then left with 2 codes,p0380 and p0487
After your mod Custom Cars, well banging my head against a brick wall, we got rid of variant code, we have NO DTC, yet we still have a limp mode and Engine Check on Dash, BTW- Thanks and Big Thanks to mihaiservice (http://www.digital-kaos.co.uk/forums/member.php/106636-mihaiservice)
I really running out of ideas on this Dog Turd of a car,
anyone Bright Ideas ??
NO DTC yet Limp mode 3k rpm and Engine Check on Dash ,,,
Petrol and Match ? :chuncky:

[mihaiservice]

You can solve it without any flame ! i have send you file in skype !just accept the file !

Regards

[pulsar2000]

You can solve it without any flame ! i have send you file in skype !just accept the file !

Regards

sorry mate, will go on skype today, and accept, i didnt see it,:chuncky:

[pulsar2000]

You can solve it without any flame ! i have send you file in skype !just accept the file !

Regards

just a update, yes i tried your file i disconnect egr and pressure sensor,
still Engine Check on screen, I throw in the towel on this Turd,
Revert to good Obd read, and let someone else deal, I really think dash fault or something ,as no DTC, yet Engine check and Limp,
Go Figure
Thanks for all help on this moFo

[pulsar2000]

You can solve it without any flame ! i have send you file in skype !just accept the file !

Regards

Resolved thanks Friend,
Good soloution,

[Helder Costa]

I have many times that problem in some ford focus and cmax and the problem is in dashboard, resolder dashboard connector.

[morphvale]

P0380 means all glow plugs are dead. Should be replaced, and not DTC deleted. With glow plugs dead, there will be no DPF regeneration, which will kill DPF in a few hundred Km.

Sent from my Nexus 5 using Tapatalk