xprog 5.5.5 for all

[aprilia40]

*Removed files as a precaution...


xprog upgrade to 5.5.5
all open
enjoy it

[kiramine]

this has Sality virus detected BEWARE!!!!

[ECU2009]

guys can anyone confirm if the virus ??

[aprilia40]

is not a virus disables antivirus, it works ok

[mara07]

Attention Sality virus!!!!

Envoy? de mon SM-G850F en utilisant Tapatalk

[kiramine]

Hope this helps if anyone got caught with this virus :)

[wyz1056]

where have download 5.55 software

[u.s]

https://drive.google.com/file/d/0B8OvMv2sg__HLXE4RmMtOEpxZWc/view?usp=sharing


https://drive.google.com/file/d/0B8OvMv2sg__Hcl9yVjlFcEVuNW8/view?usp=sharing


xprog upgrade to 5.5.5
all open
enjoy it

Is this the version originally posted by the user youneselmoukhtari?
If so then you should give him credit for it.

[Youneselm]

This forum is realy an enigma[emoji6]

[palapas1974]

Hi All! Can anyone has the firmware for LATTICE LC4064V for adepter ADP-0017 - HC (S) 12 BDM?

[vanos batam]

Hi All! Can anyone has the firmware for LATTICE LC4064V for adepter ADP-0017 - HC (S) 12 BDM?LATTICE LC4064V how to reading and program ???

[tehnosoftex]

Hi, can anyone has the schematic of adp-0019, logic level adapter from 3,3v to 5v?

[tehnosoftex]

I will make one myself based on txb0108 chip. Should be easy.

[lupu_sandu]

Archive from 1st post contain virus in xprogM 5.55.
Report here:
https://www.virustotal.com/en/file/0d971f669cd990c0ef91e20ab280107a299f94529baf16a7ab 6ab90531abee12/analysis/1459029196/
Here is the report for good xprogM 5.55 loader:
https://www.virustotal.com/en/file/eb80407479e752724198e4b5adbfda92c009bebc1dce7bcaca ba6a65f2f53a86/analysis/

[ECU2009]

boys may be one without viruses ?? thank you

[janake]

where have download 5.55 software


Free download 5.55 software:http://www.chinaautodiag.com/download/xprog-5.55-sm48-b.zip

[spychu14]

Anyone have dump for atmega for 5.5.5 ?

[vanos batam]

try this !!!
_________

[baygrozdan]

Can someone upload dumps in .hex format ? Thanks!

[thayer201]

please i need theses in .hex format too......

anyone able to help ?

thanks allready vanos batam for the files...


these are my xprog 5.5.5 non working .hex files



369501


SOLVED.........

[thayer201]

try this !!!
_________


tryed these and still have error in xprog 5.5.5 flash and eeprom loaded good. set fuse and locks
but didnt write calibration.......?

see picture :369503


any suggestion?

i will reflash again to see if it helps

[thayer201]

tryed these and still have error in xprog 5.5.5 flash and eeprom loaded good. set fuse and locks
but didnt write calibration.......?

see picture :369503


any suggestion?

i will reflash again to see if it helps




Tryed again today to flash atmega64 and eeprom with fuse and lock bits..

all hex files loaded correctly - sucsessfull flash - then write lock and fuse bits-

i run xprog software - all ok
can see all hardware id etc - all ok
auths - all green all ok

but when i read any eeprom i still get error.... certificated error...??

ive tryed fresh install of software... tryed xp sp2, xp sp3 , win 7 still have same issue.

can some one please look over my pictures and files to make sure im doing this right?

or know of a solution i would be happy for some feed back..369633369634369635369636


369637








UPDATE...... WENT TO VERSION 5.5.1 (working thanks ) awaiting atmega64 5.5.5 repair chip..



UPDATE AGAIN......... Got version 5.5.5 working as should.... software problem (dongle) using software with out dongle.. now perfect. thanks...

[marmaro]

Tryed again today to flash atmega64 and eeprom with fuse and lock bits..

all hex files loaded correctly - sucsessfull flash - then write lock and fuse bits-

i run xprog software - all ok
can see all hardware id etc - all ok
auths - all green all ok

but when i read any eeprom i still get error.... certificated error...??

ive tryed fresh install of software... tryed xp sp2, xp sp3 , win 7 still have same issue.

can some one please look over my pictures and files to make sure im doing this right?

or know of a solution i would be happy for some feed back..369633369634369635369636


369637








UPDATE...... WENT TO VERSION 5.5.1 (working thanks ) awaiting atmega64 5.5.5 repair chip..



UPDATE AGAIN......... Got version 5.5.5 working as should.... software problem (dongle) using software with out dongle.. now perfect. thanks...

HI! can you shere good software working with dump you used?

[thayer201]

HI! can you shere good software working with dump you used?


flash and eeprom from vanos above...... thanks to him for that...

and software orginal posted in this thread




..... thank to them for that....

all this work was not any of mine... dont forget to thank them..

[PATRIOT MO]

https://mega.nz/#!5tdVRBwY!aYlUKNQ16w9t7qIpC0KURS6a2DeibrYpFmY6H5N 0YCM

don't forget thanks

[Gizbern]

Friend please help with this software
Now software is deleted from first post

I have still: certificate error !!!
Thanks!



flash and eeprom from vanos above...... thanks to him for that...

and software orginal posted in this thread




..... thank to them for that....

all this work was not any of mine... dont forget to thank them..

[spiridonas]

Sorry guys i reflash my atmega with v 5.55 dump and now my xprog-m is 5.55
i tried many times software 5.55 but after about 5 times read / write says verify error.
if i replace the software working again for about 5 times.
Please can help me anyone where is my mistake ?
Many thanks in advance.

[kohli]

HMM WORK LIKE XPROGM

[Rabiee]

all my firends i bought xprog from china and i make registeration via orginal company and working good and i can update
anyone need help tell me
http://www.eldb.eu/index.php?route=information/information&path=1&information_id=4

[Gizbern]

Somebody can help with eeprom and flash for atmega 5.55 with dongle version ?
Thanks

[Gizbern]

Maybe problem with date in the PC
or connection to network
(xprog connection by LAN)

[hass42]

try this !!!
_________

This may seem very amateur to say, but what do I do with conig.bin file?

[thayer201]

xprog 5.5.5 no dongle software.

as of yet working good no problems.

software on here posted has salty virus...

finally found working with no virus.

shared : 59 wanted 2 thanked..

If it works for you...... please dont forget THANKS...........

[hass42]

xprog 5.5.5 no dongle software.

as of yet working good no problems.

software on here posted has salty virus...

finally found working with no virus.

shared :384621
I verify that this is a clean version that worked with me. Haven't tried on all chips ....but worked no issues

Hass42

[spiridonas]

Hi, i tried the software and after reading 5 times the 93c56 says Verify errors.
Please what is the problem ?
Many thanks in advance.

[thayer201]

Hi, i tried the software and after reading 5 times the 93c56 says Verify errors.
Please what is the problem ?
Many thanks in advance.

ive not had this problem but will test later today.

[spiridonas]

when replace the configuration.xml file working ok for the next 5 times and after verify errors again.

[hass42]

when replace the configuration.xml file working ok for the next 5 times and after verify errors again.
Are you connected to internet?

Hass42

[spiridonas]

Yes connected to internet.

[hass42]

Yes connected to internet.
I'm not 100% sure, but that maybe your problem

Hass42

[spiridonas]

i tried without internet and i have the same problem

[Faraday]

ESet reports Win32/Virut.NBP

[Gizbern]

i tried without internet and i have the same problem

Reinstall, and LAN OFF
Try again!

[thayer201]

ive had no problems today... , disconnect internet first and THEN unpack rar, then install. and try again.


and then dont connect back to internet as you will have to do it all over again.

[spiridonas]

I reinstal without internet and now working fine.
Please how can work with internet ?
Need to enable firewall about xprog port ?
Thanks

[thayer201]

I reinstal without internet and now working fine.
Please how can work with internet ?
Need to enable firewall about xprog port ?
Thanks

i couldnt get it to work with internet on aswell... allways seems to kill the software then have to re unpack everytime ...but if anyone figures it out let us know.

Glad the software working good for you now.

[aem]

i can confirm.install without internet and work without internet there is no verify error never.working perfect

[912secured]

5.5.5 runs fine releasesd on mmh originally. Your not setting you fuse bytes right??? and it only likes to run on xp (virtual machine helps).

[urcarpc]

Hi, ive already got an x-prog 5.55 with dongle. Can I run this software without flash atmega chip? Thanks

[mikeg332]

Does anyone know if i can downgrade my xprog m 5.6 clone to 5.5.1? and use it without a dongle? Any information would be greatful




Hi, ive already got an x-prog 5.55 with dongle. Can I run this software without flash atmega chip? Thanks

[jakesman]

m8 if u can get the files for atmega and eeprom , u can flash it to that version so up or down do not matter aslong as u have the files and software that goes with it u should be fine , i went from 5.3 with dongle to 5.5.1 and up to 5.5.5 and down to 5.5.1 and again up to 5.5.5

[mikeg332]

Thanks bud for your prompt response. It is much appreciated :)

[H2Deetoo]

Hi guys, do you know if there are files available for v5.60 ?
I currently have v5.55 without dongle.


Rgs H2Deetoo

[Rodi81]

Por favor, pida ayuda con mi xprog 5.6 error: silenciosamente dispocitivo.
Si puedo ser detallado lo que hay que hacer ya que soy nuevo en esto. ¡¡Muchas gracias!!.

[wokcz]

Por favor, pida ayuda con mi xprog 5.6 error: silenciosamente dispocitivo.
Si puedo ser detallado lo que hay que hacer ya que soy nuevo en esto. ¡¡Muchas gracias!!.

Try different usb cable and make sure the COM port in xprog software Oprions > Environment is the one you see xprog is using in windows device manager when you plug it in, if you don't see it in device manager then you have a drivers problem, try reinstalling them. Also write in english, no todos hablan español aca.

[Rodi81]

Hello and tested don different usb cables and still giving the same error and tested in xp (32bist), win7 (32bist), win7 (64bits) and does not work.
It is xprog 5.6 with dongle.
I can flash it to some other vercion. I have the programmer upa to be able to flash.
In the case of flash to which vercion they recommend me.
I will be very grateful for your help !!

[wokcz]

Hello and tested don different usb cables and still giving the same error and tested in xp (32bist), win7 (32bist), win7 (64bits) and does not work.
It is xprog 5.6 with dongle.
I can flash it to some other vercion. I have the programmer upa to be able to flash.
In the case of flash to which vercion they recommend me.
I will be very grateful for your help !!

Your error seems to be the software has no communication with the device. Did you make sure the COM port set in xprog software is the same assigned to the device when you plug it in? If nothing else works, yea I'd say try reflashing it, sorry I can't recommend a specific version, mine works well out of the box without reflashing so far.

[Rodi81]

Hi Wokcz if the communication, ports and drivers are correct.
My question is whether flash can be done to any vercion and if the software has to be with dongle obligatorily or is indifferent (I consult this since my computer is with dongle).
Another question is how to charge the authorizations, or are loaded automatically with the flash and / or software.
I am very grateful for your help.

[Rodi81]

Another question I have is that I must do first. If you upload the eeprom file and flash or modify Lock bits and Fuse Bits.
I check this out because when loading eeprom and then modifying lock bits the content of eeprom is modified.


I do not think it's a software problem because three of our colleagues have the same problem with xprog 5.6 with dongle

[wokcz]

Another question I have is that I must do first. If you upload the eeprom file and flash or modify Lock bits and Fuse Bits.
I check this out because when loading eeprom and then modifying lock bits the content of eeprom is modified.


I do not think it's a software problem because three of our colleagues have the same problem with xprog 5.6 with dongle

If you flash it, you wont need to use the dongle anymore I think. Sorry I can't comment much on the flashing procedure, I never did it so far, I have 5.4 with dongle and haven't tried upgrading it yet.

[weistec]

i have xprog software 5.55 but when i put usb the xprog device but it unable to communicate port

[cubica1]

do not waste time friend, leave 555 version and go to v551...it is stable version...
regards,
cuby

[heteromies]

share 5.55 software link?

[samranisimo]

how to Config.v5.5.5.bin xprog thanks

[casper2]

I need xprog 5.5.5 install. I will be glad if you help.
i need setup file

[jiajun]

thanks brothers