Nissan Primera P11 remote programming problem

[mellon]

HI,
I have Nissan Promera 2001 year and problem with enter to remote programming mode. One key working very good but second not working. I put ignition 6 time to on and off but car does not respond by flashing. I put key on off postiion or take out and the same. I can't enter to program mode. I try many times slow and fastes way. I change ignition switch to second and check switch in barrel but is ok.
Please help.
Adam

[Zeddy]

Hi,

Could be be water damage in control unit.

Right hand kick panel.

Thats according to IQ.

[sbtriny]

HI,
I have Nissan Promera 2001 year and problem with enter to remote programming mode. One key working very good but second not working. I put ignition 6 time to on and off but car does not respond by flashing. I put key on off postiion or take out and the same. I can't enter to program mode. I try many times slow and fastes way. I change ignition switch to second and check switch in barrel but is ok.
Please help.
Adam

hi, m8.
you mean key ignition on to off 6times?
it's not correct procedure.
1. close all doors
2. doorlock locked by lock switch driver side
3. insert and remove from ignition, 6 times(within 10sec)
4. car response(harzrd lamp flash twice)
5. put key in ignition on
6. press any button on remote. then car response.
7. open door for exit programming mode

try this.

good luck

[P&D]

It is correct for UK models.....correct programming is


1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.


2. Then turn ignition switch to OFF position. Take key out of the ignition
3. After 2 seconds, the system will enter programming mode and will flash the warning lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key?s.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key?s for operation.
NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys have been programmed or no input signal either from the switch or plip keys has been received for 120 seconds.

[mellon]

I repair remote controls about 10 years so I realy don't have problem to enter programing mode in primera before. This first car with this error.

[Meat-Head]

Try this

1) stand on one leg
2) disconnect battery
3) battery lead in one hand, use i~~~~ to
Press a few DK thanks buttons
4) swap over legs (max time 1 second)
5) reconnect battery
6) repeat above experiment earlier mentioned
7) does interoir light work correctly?

[mellon]

Try this

1) stand on one leg
2) disconnect battery
3) battery lead in one hand, use i~~~~ to
Press a few DK thanks buttons
4) swap over legs (max time 1 second)
5) reconnect battery
6) repeat above experiment earlier mentioned
7) does interoir light work correctly?

I stand on my head :) disconnect battery even on 5 hours, interior light works correctly and not enter to pramming mode. One key open and close doors, second I check frequency meter and is ok but not work on car only enegine runs. I will check control module as Zeddy said.

[Meat-Head]

Sounds like lost ignition feed, do you have anither car to borrow/check all fuses?
plug your midule into anither car.

or

love you longtime locking kit ebay, to work that remote

[szkeptmen]

KEY FOB PROGRAMMING
NISSAN

SYSTEM DESCRIPTION

The Central Door locking is controlled by the Multi-Remote Control system which controls
the door locking, door super locking and haz ard reminder. When the doors are locked and
unlocked the unit flashes the hazard lights once for lock and twice for unlock.

A maximum of four remote controls are allowed to be programmed.

ALMERA
ALMERA TINO
PRIMERA
MAXIMA
MICRA
SERENA
VANETTE CARGO
TERANO II

Ensure all the doors have been unlocked, either by using a good transponder key or re-
mote control plip key.

Procedure

1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.
2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning
lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key’s.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key’s for operation.

NOTE : The programming mode will stop when either the ignition is switch ON, 4 plip keys
have been programmed or no input signal either from the switch or plip keys has been re-
ceived for 120 seconds.

WBR

[mellon]

I don't have point "3". Pozdrawiam bratanka. :)

[rideon]

I will check control module as Zeddy said.
Don't bother checking ,since one key is working...
Best advice is to follow MH procedure 1 to 6 with few extras..
2.5 coffee brake
3.5 union brake

You can also try leaving ignition on/off battery leads on/off login/logout DK


I usually leave the car parked somewhere in a corner and repeat the procedure every now and then, by the end of the day should work,else there is always tomorrow...


Worst part is ,when it finally works, you have no idea WHY!!:ahhhhh:

[Meat-Head]

Does sound like dud module abd/or no ignition feed

seem ti think there are two modules relating to locking

[obdsystems]

it's a 15 year old car - bound to be some electrical problem. probably mcdonalds burgers wedged into something...

coffee break and if all fails, check wiring 1st, then pop down local scrapie, plenty about

[parapilot]

all doors need to be unlocked or it wont go into programming. check they are all open, and none faulty / locked.