etpvn
4th April, 2016, 08:33 PM
Hello Mate,
I have hyundai Santafe EDC15C7, the car run normally, I just took out the ECU from car and try to Read Dump from EDC15C7
- 1st I read SAK-C167CR-4RM internal and 29F400B by Piasini V4.1 ok, read Eeprom 5P08C3 as 95P08 also OK.
- 2nd I read 29F400B by Xeltel 580U ok (Also try to read by Digimaster 3 for 29F400B but not connected - Digimaster worked normally for other 29F400B - I really wondered because i have used Digimaster 3 for 29F400B (from BMW 325 - MS43) no any problem, but now cannot read 29F400B from Santafe EDC15C7, 10 times with error: Not find device)
Then I soldered all ICs : 29F400B, EEprom 5P08C3 to the PCB of EDC15C7
cleaned and check all soldered Pins ok, by Microscope magnify more than 1000 times check ok!
Then i plug ECM to Car, Turn key to start ok, run around 10 km, Car stop suddently, then the Check Engine light stop when turn ignition ON, ECM cannot accessed by Hyundai GDS, 2-3 time check engine light ON then it can be worked, then finally check engine light turn Off for NO more time ON, when Igniton Key at ON possition! Cannot read DTC.
I really Wonder, I have many times reading dump and backup with No Problem, but now i cannot understand!
When i Try to backup program of 29F400B by Piasini V4.1, but process stop at 10% with Error. and reprogram by Xeltek 580U to other 29F400B IC, but still got No check engine light when Turn Key ON.
So I attached dumps of EDC15C7 of Santafe to get help from Expert to check for me!
This Santafe has no Immobilizer.
Im really thankful to you all, DK members!
367689
367685367686367687
I have hyundai Santafe EDC15C7, the car run normally, I just took out the ECU from car and try to Read Dump from EDC15C7
- 1st I read SAK-C167CR-4RM internal and 29F400B by Piasini V4.1 ok, read Eeprom 5P08C3 as 95P08 also OK.
- 2nd I read 29F400B by Xeltel 580U ok (Also try to read by Digimaster 3 for 29F400B but not connected - Digimaster worked normally for other 29F400B - I really wondered because i have used Digimaster 3 for 29F400B (from BMW 325 - MS43) no any problem, but now cannot read 29F400B from Santafe EDC15C7, 10 times with error: Not find device)
Then I soldered all ICs : 29F400B, EEprom 5P08C3 to the PCB of EDC15C7
cleaned and check all soldered Pins ok, by Microscope magnify more than 1000 times check ok!
Then i plug ECM to Car, Turn key to start ok, run around 10 km, Car stop suddently, then the Check Engine light stop when turn ignition ON, ECM cannot accessed by Hyundai GDS, 2-3 time check engine light ON then it can be worked, then finally check engine light turn Off for NO more time ON, when Igniton Key at ON possition! Cannot read DTC.
I really Wonder, I have many times reading dump and backup with No Problem, but now i cannot understand!
When i Try to backup program of 29F400B by Piasini V4.1, but process stop at 10% with Error. and reprogram by Xeltek 580U to other 29F400B IC, but still got No check engine light when Turn Key ON.
So I attached dumps of EDC15C7 of Santafe to get help from Expert to check for me!
This Santafe has no Immobilizer.
Im really thankful to you all, DK members!
367689
367685367686367687