E240 w211 2005 after key makeing can't start (pleae help)

[Frankcar]

Hi friends
i have a w211 E240 2005 that lost all key. i read eeprom EZS with R260(Rosfar) programmer
After calculator key and test on car , EZS detect new key but car can't start , remote work. ESL lock and unlock , Only IGN on , but car can't start

EIS part number: 211 545 17 08
ME: A 113 153 22 79 (benzin) BOSCH (0 261 207 709)
95p08 eeprom

i sure hardware EIS no problem, i think problem data ME(ecu)
anyone can help me that what is problem ? maybe i need to sync , for sync how i can do ?

thanks

[mercis]

first check fuse for starter on sam front,often bad on w211

[simon77]

check to see if there is power on the purple wire from sam to starter as mercis said

[Frankcar]

this car have problem data, i sure

[Mr BLACK]

open again ezs and check for soldering or someting on pcb...

[Mr BLACK]

or use diagnostic and see if u have start enable in engine ecu

[Frankcar]

immoblizer Active .
computing data...........
Driver authorization : NO

now i have only AVDI orginal MB
i try with AVDI: adaptations - drive authorisation ----- immoblizer active

[smayer]

Try use a good key, maybe this car don?t like chinese key.

[daxxer]

immoblizer Active .
computing data...........
Driver authorization : NO

now i have only AVDI orginal MB
i try with AVDI: adaptations - drive authorisation ----- immoblizer active

show the screen of Star diagnostic about drive authorisations from EZS....
are you rightly learned the new key in all positions ? :driver: when not, the key is still not right learned in ECU :listen:

[Frankcar]

i think some models w211 have this problem
because yesterday i had a E230 2004 that need spare key. original key without problem ( remote and start ). i read data EIS and password via IR without problem then i tried to making new key with version 57 EZS detect new key but only lock & unlock ESL and doors ok but car can't start ( computing data ... ) i wait 20 min but useless.
original key (working key) not have problem.

i think data ecu have problem . anyone can help me ? which software can sync EIS and ECU ?
I hear there are some software for sync EIS and ECU (without SD connect or Star MB)

[daxxer]

i think some models w211 have this problem
because yesterday i had a E230 2004 that need spare key. original key without problem ( remote and start ). i read data EIS and password via IR without problem then i tried to making new key with version 57 but only lock & unlock ESL and doors ok car can't start ( computing data ... ) i wait 20 min but useless.
original key (working key) not have problem.

the "computing data" with symbol in middle display can be from 1 secs to 2 hours ( described in WIS ) :listen: connect charger and wait...
you need to see actual values of EZS through Star diagnostic and wait in all positions of EZS, when you get YES, YES, YES and at end YES for Ecu unit...then is the new key allowed in ECU and start is allowed...without this last step you can try it 10x...20x...or more without any successful result :(
the new key can't be rightly learned to ECU unit before, then ECU unit have power +12V, and this have first when you turned key to ignition ON...then there is needed to wait some time... for learn key to ECU :listen: what you not understand at this last step ? ;)
you are too fast :D

[abvayani]

Mate its a Flash problem, happend with me so many times, find Flash with the same Eis number

[Frankcar]

for previous car i send dump eeprom EIS and eeprom ECU for a friend and he send me a new dump ECU , after write on (95p08) ECU i tried for making new key and car very good start.

[kohli]

I THINK SOMETHINGS INSIDE EZS unsoldered

[Frankcar]

I think for voltage fluctuations that data ME damage

[vanos batam]

write to the ECU or ME..
start the car..
if not work.. iam sure from other problem....


regard