mc68hc11e9 4e28b with upa ?

[ibratex]

Hello mates i am trying to read mc68hc11e9 mask 4e28b with upa usb and i am getting

HIGH RESET ERROR


I took the proccessor ou since its impossible lift pin its from lm320 bosch ecu i am trying immo off with emulator


I have r270 can it read ?


While i am searching i saw post about doing autobraud but i didnt know what even that means please help ....thank you

Sent from my SM-G900H using Tapatalk

[kiszka]

..............

[cubica1]

very simple to read/write my friend, no need to lift any pin.
rgds,
cuby

[ibratex]

the sea it will help
380674
Thank you for helpin but i always get error

Sent from my SM-G900H using Tapatalk

[ibratex]

very simple to read/write my friend, no need to lift any pin.
rgds,
cuby
Cubica1 thanks mate i already tried by removing and onboard the same error always reset high error and in connection test

RXD : 0.02 V BAD
RESET: 1,66V BAD



Sent from my SM-G900H using Tapatalk

[ibratex]

http://uploads.tapatalk-cdn.com/20160610/3a6e9fa97dc456bc2cbefb18e677950b.jpghttp://uploads.tapatalk-cdn.com/20160610/8e84644137bc899745bf50eb54262af3.jpghttp://uploads.tapatalk-cdn.com/20160610/8211a84b162d0603408116a9858fc4ed.jpg

Sent from my SM-G900H using Tapatalk

[kiszka]

..............

[ibratex]

what you mean ...lift pins ? if so the pins are arc shaped its impossible lift pins and leave others ... or i can get all of pcb or none

[cubica1]

lift up only problematic pins: Rx and RESET, than connect UPA wires to them directly.
cuby

[ibratex]

hhehehe didnt need design bro come on ...thanks i will try

[ibratex]

http://uploads.tapatalk-cdn.com/20160611/0c5baf120d7eb9a8e4470b905f511498.jpg


Now all test give ok but when read same error reset high error

Sent from my SM-G900H using Tapatalk

[vlaki electric]

rinse vss,reset and txd mate and he must read

[antwnhszr]

do you have adapter for this mcu?for upa?if not......don't try to read on the pcb.....

[Jan1980]

I was in same trouble with this mcu last time. I fixed my problems. I have read 4E28B many times in Benz ME2.0 ECU without problems. Then, i wanted to read in an old Benz Lucas epic phase 1 ecu. Same solution not working. It doesn?t care where the mcu is located ! I had to lift reset, rxd, txd and vdd !! Then, everything works without problems !

[cubica1]

yes, that's why I hate UPA :) time to time, from place to place, you have all parameters Ok and green colored, but still can't read :(
As @vlaki electronic and @jan 1980 told you, now try to lift up supply line, Rx and reset..all of them and try again, don't give up.
As you can see on my picture above, I have r/w the same processor w/o lift any pin on VW Beta 4 radio.
Good luck,

regards,
cuby

[ibratex]

jan , what connection you used this ??380810 or this ?????380811

[ibratex]

i have adapters but there are 3 adapters i that can fit the processor 4e28b , what adapter type ? i have type 9 type 3 and type 7 all fit the proicessor but i dont know what is the best and already tried the 3 and type 9 have a jumper ...do you have pic ?

[ibratex]

Iammmm happpyyyyyyyyy

Sent from my SM-G900H using Tapatalk

[ibratex]

http://uploads.tapatalk-cdn.com/20160611/aa78225ae51cca81ac8e6760722f4364.jpg


No surrender thank you mates i was about to leave it but ittttttt apppeaaared thank you from heart foe your time

Sent from my SM-G900H using Tapatalk

[ibratex]

solution was adapter type 9 of-board thanks again

[IRHABOR Monday]

Please somebody should help me this MCU 4E8B connection with UPA or XPROG to read it

[ibratex]

Please somebody should help me this MCU 4E8B connection with UPA or XPROG to read it
Upa adapter number 9 http://uploads.tapatalk-cdn.com/20160807/310142bd4eba5d01c0e8473ec030f10d.jpg

Sent from my SM-G900H using Tapatalk

[djeuroalex]

solution was adapter type 9 of-board thanks again

can you post close photo to see what oscillator and diagram on both sides of adapter 9 . Thanks!

[rob h]

I read it with oem upa, and only lifted txd and rxd.


Does someone have a good techique? For lifting pins in the future.

I first considered cutting, but this can ripp the pcb track.

I ended up, pulling the 2 pins to the outside,and created a small gap.
And did not pushed them back, all the way. But just ennough to solder a connection.

Any tips and tricks, with some pictures perhaps.

Thanks