PDA

View Full Version : MB ML350 CDI W166 Bluetec AdBlue and DTC OFF



phl0at
18th July, 2016, 04:31 PM
Hello guys.
I am in a struggle of removing AdBlue and NOX off from a ML 350 CDI W166 with EDC17CP46.
It has 2 DTCs: P2BAD and P2BA8 which i need to delete also. It has a MIL light on because of these two i think they are related to NOX and adblue quantity.

Has anyone got a solution for it?

Here is a BDM read of the EDC17CP46 ECU:
387359

phl0at
18th July, 2016, 08:00 PM
Also any damos for that ECU are much appreciated!

obdflasher
19th July, 2016, 03:08 AM
I have:

[WinOLS]
ClientName = *Removed Email Address
ClientLicenceplace = Super Mappack
VehicleType = Passenger car
VehicleProducer = MB
VehicleSeries = ML
VehicleModel = 350CDI
VehicleModelyear = 2012
EcuProducer = Bosch
EcuBuild = EDC17CP46
EcuProdNr = CR60-642LS-9FL0-Ch4_Q2-166WA-EU6OPS_4x4_3S-ME04_02
EcuSoftwareVersion = 516312
EngineType = Turbo-Diesel
EngineDisplacement = 3.0
EngineTransmission = Automatic transmission
Userdef1 = German
OutputPS = 258.0
OutputKW = 189.8

gitko
22nd July, 2016, 08:37 PM
here you can disconnect SCR module and all sensors from DPF

wassim22
23rd July, 2016, 12:23 AM
hello please i need a help for this ecu edc17cp46 0281018333 mercedes glk bluetec 250cdi 2013
i have a galletto 3v54eu from caprog
i have connect boot mode in connction it's ok but in read i have error unlock password read try tool tricore password tprot v08
i have tested with tricore password tprot v08 but impossible error any solution please how to unlock this ecu

phl0at
2nd August, 2016, 11:19 AM
Have you connected the boot pin with the grey strip?

wiski
2nd August, 2016, 02:08 PM
Ori Fgtech can do it not clone

Sent from my SM-A510F using Tapatalk

phl0at
26th September, 2016, 07:37 AM
Hello guys, the Merc returned with the AdBlue tank empty! No DTCs present in the controller, but it seems that it is not fully off but only the DTCs deleted as I can see in the dump. Anyone has a solution for adblue consumption off?
I attach the file and will greatly appreiciate your help!


399869

Emre2blue
8th May, 2018, 11:08 AM
Can you give me only VNT maps for this file. I bought a turbo from 350CDI, and I use the electrical actuator. I need to find VNT % for this controller to apply them to EDC16C39. I need boost maps and VNT % I have files. But I don't have map pack or damos. I don't need them , only VNT and boost maps. Would you please share it with me also ?

voltechcar
8th May, 2018, 11:56 AM
because empty? you must disconnect module scr !!!!!!!!!!!

Emre2blue
8th May, 2018, 12:14 PM
because empty? you must disconnect module scr !!!!!!!!!!!

Is this reply for me ? I don't understand what you mean?

remteh
16th July, 2019, 06:41 AM
Hi!
This is an old thread but maybe someone has information?!
MB w166 350cdi bluetec - done dpf, scr, egr off and now car has multiple can communication errors. Drives ~100km and can starts acting crazy?
U0100; PC121; PC100; PC126; PC164; PD10B; PC167 and etc.
All modules and sensors are connected. If disconnecting scr ecu no change at all.

Anyone ideas?

lesm
19th February, 2020, 08:35 AM
Hi

please supply password to open the file

Thanks