2009 VW Tiguan need cluster bin file

[techterr]

Hello DK,
Have a cluster a friend sent me from a 2009 Tiguan. The cluster is a 5N0920870C Would anyone have a bin file that would work on this? or can anyone look at the file and see if they see any errors?
Thanks in advance,
392909

[techterr]

Have tried a couple bins that i downloaded, they make the cluster light up, but I can't read the immo data??? Would anybody be able to find the CS and pin in this bin? Maybe I can precode a chip and then be able to program a key...
392910

[H2Deetoo]

What exactly is the problem with this Tiguan cluster? And what do you want to do with it?

Reading/writing immo data (like CS and PIN) or mileage can only be done using OBD with proper tools.
This cannot be done by eeprom alone.

Edit: I see now that you've uploaded your immo data. Tonight when I am home I can give you CS, PIN etc from that data.
Also the eeprom file you posted is not correct, it has about 125 leading bytes which shouldn't be there. I can check it in detail later.


Rgs H2Deetoo

[techterr]

Thank you H2Deeetoo... I read, and wrote the data with AVDI. When the original file is written to the cluster, it is dark and silent until you try and read data from it, then it lights up, at least the icons in the guages light up, but the center screen stays dark. When I write the other file to the cluster, the center info screen lights up, and so does all the icons and it looks like a regular cluster... except I can't read the immo data.. AVDI comes back and says, immo config unknown, send logs to dealer...
Thanks again for any help...
PS, i have the immo data from the first file, just don't have the info from the 2nd file... Which file do you see the extra 125 leading bytes?

[H2Deetoo]

The 1st file you uploaded is an immo file.
The 2nd file you uploaded is an eeprom (which is too long).

It seems your current eeprom is damaged, because LCD stays black.
Can you upload your current eeprom? I will test it here and perhaps I can repair it.
Other solution would be use new eeprom, and copy immo data from old eeprom (area 13C0-14FF should be sufficient I think).


Regards,
H2Deetoo

PS. You can PM me for quicker communications

[techterr]

Sorry, that was the first read of the cluster... Still not sure why the file was only 130 bytes... Here is the 2nd read...
393092

and here is a pic of the data I read from the ECU,
393093

Thanks again for any help...

[wojciech300]

Vin :WVGZZZ5NZ9W096818
Power Class: 6A
Pin: 26175
MAC1: 91EA
MAC2: B8CA
CS: 40C063048180C6
Immo ID: VWX7Z0I23NC7XH
Key1: 04C85EED
K2: 2FD15EED
K3: 2FED2D02
K4: C4042E02

[techterr]

Thank you wojciech300....
Woulkd you be able to pull the data from this bin? The first bin is having issues when uploaded to the cluster... the center screen stays dark and the icons only come on after you log into the cluster... I wrote this file to the cluster and the center screen lights up, but I am not able to get into the immo to program the keys or change the CS...
Thanks in advance...

[techterr]

Hi Guys, I am still fighting this... I know I am going to look stupid, but here goes... Can someone point me to where the CS and immo info would be in the file above? I am having a hard time finding it..
Thanks in advance..

[someone93]

If the problem is corupted eeprom, just copy immo area form corupted to good eepromm like H2Deetoo said and will work.

or post both eeproms, and I will do it for you.