Renault scenic 2007 card programming problem

[Nikola1309]

I have problem with programing card for scenic 2007 year. I done this cards a lot but have strange problem, try fnr ( clone truecode), carprog and fvdi. With fnr reads all data, pin, etc and when click on start programing get error, after that try with carprog and he reads pin code, but when i try to add card says wrong pin, fvdi cant pull pin out. Pin is the same with fnr and carprog. Does somebody know what is happens?

[teerak2uk]

My fnr don't work but I did mine with carprog 8.21

[Nikola1309]

My fnr work until now without problems with megane and scenic cards, but now wont work. Also fvdi can not pull pin out. Carprog 8.21 says wrong pin.

[Sergio101]

Hiya

I have had this once or twice on megane 2. I solved it like yanking out a pair of fuses and putting them back. On the megane, it was one that said something like alim auch, and the second colsole if i remember correctly, seems to reset the ecu/immo but doesnt reset the radio so yo wont need pin. on the scenic i believe there are 2 fuses with a little picture of a dash or set of speedometers. give it a try, in my case it worked every time. btw, i used fvdi

[vlaki electric]

try to add batery charger when you code the cards with fnr.

[KILL_THE_IMMO]

CHECK FUSES I HAD THIS PROBLEM

[nbn]

Hello i have the some problem not Reding with fvdi and pin wrong with carprog.did somebody have solved it.thanks

[issam216]

i had the same problem with clone true code but when i program it with fvdi 2014 it works perfectly try again may you will succed

[Nikola1309]

Just remove two fuses like sergio101 said and fvdi will program cards.

[morfej]

You have facelifted scenic II ... your pin is not correct one.

br

[T2000]

Hello,
I have the Megane 2 Phase 2 - which I belive is also very similar to the "facelifted" version you were mentioning.

I now really have to solve this problem. I tried FVDI 2015 which is not starting the Renault loader. I also tried DDT4ALL which does not recognize the ISK, so I guess it is outdated.

I don't know for sure which software works. Some say RPE3 - but I don't have it. Can somebody help?

I found the ISK, but can't find the correct PIN.

ISK CODE: 15A9936B6377

And very important - which software can I use to actually make the car learn it? (DDT4ALL seems not to work).
Would be so so great!!!
Thanks in advance!!!

[Catalizator]

Hello,
I have the Megane 2 Phase 2 - which I belive is also very similar to the "facelifted" version you were mentioning.

I now really have to solve this problem. I tried FVDI 2015 which is not starting the Renault loader. I also tried DDT4ALL which does not recognize the ISK, so I guess it is outdated.

I don't know for sure which software works. Some say RPE3 - but I don't have it. Can somebody help?

I found the ISK, but can't find the correct PIN.

ISK CODE: 15A9936B6377

And very important - which software can I use to actually make the car learn it? (DDT4ALL seems not to work).
Would be so so great!!!
Thanks in advance!!!

if you do that, it is very bad. I gave you all the information and pin. refuse to believe, then cope with your work.

[ccdiag]

Just got back from doing a 2008 Megane. Exactly the same issue as above but using genuine carprog - there is a separate program for the 2007 and I had no wi-if in the area that I was working. One I had tethered the laptop to the phone, the carprog connected online produced the correct IMMO details in about 3 seconds and the card programmed perfectly.

Jezza