Renault Clio II 1.4L Sirius32N Immo Problem

[258]

Hi,
Car have problem with immo , no key recognized immo key status,.
Need immo off ,have AC . I tried one solution with cut wire 58 not working.
Can anyone help me with work solution.
1,4L ECU Sirius 32N 2001year.

[VictorBazan]

Best Regards from Chile

[258]

Best Regards from Chile
I try it today, wire from 58 pin must be cut?

[VictorBazan]

Yes, cut 58 pin

BR

[258]

Cant write file, checksum error

[t77]

Try this and cut pin 58. Pass in PM

[albertros]

Hi,
better to find fault.
Start by resolder chip in key then check aerial in key
Swap rectangular relay in fuse box, change 3 fuses (battery fuse box)
check 2amp fuse in end of dash.
Check engine earth - put jump lead on bat+ and engine block

[258]

Chip in key resolder all ok and clean.

[albertros]

Hi,
after check above, remove white plug in uch for a few seconds then plug back
thats 2001 with aerial at back of roof

[Meat-Head]

Copy the transponder onto a T5 chip close eyes
remove orginal board expect it to start

[258]

T77 your file work not.

[antwnhszr]

Hi,
Car have problem with immo , no key recognized immo key status,.
Need immo off ,have AC . I tried one solution with cut wire 58 not working.
Can anyone help me with work solution.
1,4L ECU Sirius 32N 2001year.

start your car......cut the 58 pin don't need anythink else.
pass on your pm..

[258]

start your car......cut the 58 pin don't need anythink else.
pass on your pm..
Not work, no crunk

[Tedum]

Not work, no crunk

HERE IT IS FOR YOU PRESS THANKS

[Meat-Head]

Not work, no crunk

what a donkey, you need to short out the starter relay and press thanks

[258]

what a donkey, you need to short out the starter relay and press thanks
I mean, Starter work,but car want not start.

[lion0304]

Not work, no crunk

If starter not crank, it seem that UCH problem.

What is the status of immo light? Flashing fast? Light stay ON?

What is Clio 2? PH1 or 2?

Radio antenna in front it's PH1 Kline, immo iD33

Radio antenna behind, clio 2 PH2. Immo iD46 PCF7946. CAN system.

Also it's the first and last time i reply to your post if you are not ABLE to be POLITE with members trying to help you.

[258]

If starter not crank, it seem that UCH problem.

What is the status of immo light? Flashing fast? Light stay ON?

What is Clio 2? PH1 or 2?

Radio antenna in front it's PH1 Kline, immo iD33

Radio antenna behind, clio 2 PH2. Immo iD46 PCF7946. CAN system.

Also it's the first and last time i reply to your post if you are not ABLE to be POLITE with members trying to help you.
Immo light flashing fast if ingnition turn on, that is clio II ph1 k-line in Ecu no CAN chip.I check key inside, immo antenne connection all like ok.remote car unlock with key work ok, i tried all solution from here with immo off,but the car will not start.I will try it with emulator.

[Tedum]

Immo light flashing fast if ingnition turn on, that is clio II ph1 k-line in Ecu no CAN chip.I check key inside, immo antenne connection all like ok.remote car unlock with key work ok, i tried all solution from here with immo off,but the car will not start.I will try it with emulator.
Try my file

[Tedum]

HERE IT IS FOR YOU PRESS THANKS
Try this one

[258]

Try my file
I try it today, thanks

[Meat-Head]

How you reading/wriying the file?
have you tried copy key onto T5?

[258]

Read and Write in boot mode an Bench, and 2 Solution with programmer.
I have no tried copy key.

[albertros]

hi,
if you post dump from 93c46 in uch someone can give you overide code. (and generate t5 transponder data, I beleive tmp pro will do this)
If the car starts fine if the car still not start you have another problem.

This is a an easy job dragging on.

[258]

Try this one
Car started 1 time for 6-7 seconds, motor again assumed. Im waiting for emulator, if with emulator work not, i think ecu is Problem.

[Tedum]

Car started 1 time for 6-7 seconds, motor again assumed. Im waiting for emulator, if with emulator work not, i think ecu is Problem.

Just write the file again and before trying unplug uch first

[258]

Ok,i try it again and report

[albertros]

Hi,
the way to test the immo is to turn on the ign, wait 3 secs then crank. As the light flashes fast I think you will find the car wont crank, (please report) If you wizz the key in and round, often, even though the immo is active it will crank for 2 or 3 times.

If the light flashes fast I would suspect a fault between the key and the uch. If the fault is between the ECU and UCH I would expect the light to stay on.

As the car is absent, from past experience the key is the first place to look.
The chip often responds to being re-soldered as does the wire wound aerial, althogh I often end up replacing the aerial.
The aerial is not for the remote locking.

I have only had a faulty ring decoder twice, if you replace it make sure the numbers match.

[258]

Hi,
I check today ECU Supply voltage at pin 30 bat 12+,29 ingnition +12, ground is ok, pin 39 ecu relay , if ingnition off pin 39 have 11,89 Volt , if ing on 0,11 Volt all is ok, pin 66 +12 is ok. All fuse and relay is ok. I tried with immo off and original dump same problem immo light flashes fast, car wont not start.Key is resoldered. UCH have 3 plugs black,yellow and blue, if yellow plug put out immo light is off, cant find wihte plug.
Maybe Albertros you're right ,fault between the key and uch.
Tedum i tried immo off again , first unplug uch, then start car, same problem.
if emulator installed i report work or not.

[Tedum]

Hi,
I check today ECU Supply voltage at pin 30 bat 12+,29 ingnition +12, ground is ok, pin 39 ecu relay , if ingnition off pin 39 have 11,89 Volt , if ing on 0,11 Volt all is ok, pin 66 +12 is ok. All fuse and relay is ok. I tried with immo off and original dump same problem immo light flashes fast, car wont not start.Key is resoldered. UCH have 3 plugs black,yellow and blue, if yellow plug put out immo light is off, cant find wihte plug.
Maybe Albertros you're right ,fault between the key and uch.
Tedum i tried immo off again , first unplug uch, then start car, same problem.
if emulator installed i report work or not.

with my file immo blinks while you plug the uch and do you know that to use emulator you must have to edit lines in flash?

[258]

with my file immo blinks while you plug the uch and do you know that to use emulator you must have to edit lines in flash?
Yes,with emulator i know. I dont know why immo off dont work.

[Tedum]

Is your car 16v ? Also check after writing my file unplug one ignition coil from spark plug make the ignition coil tip near to a metal surface then let some one try to start the car let me know if you see spark on it




take care while doing this high voltage

[Tedum]

http://f.tqn.com/y/autorepair/1/S/j/-/-/-/plug-wire-out.JPG
Like this

[258]

hi,
yes car is 16v,with your file and unpluged ingnition coil no spark .Fuel pump work ok.
http://uploads.tapatalk-cdn.com/20160907/c02589cd924a784bb4c26483226a228b.jpg Ecu
http://uploads.tapatalk-cdn.com/20160907/3e965ecdfa36a99226b3b752148ef578.jpg UCH

[Meat-Head]

Unless ecu driver faulty

[antwnhszr]

how to put all this file's on the flash?with boot?what tool you use? under the pvb you can find one ic with number's:A82C250?it's ic with 8 nleg's and like as eeprom....lookink and tell us.....

[Tedum]

how to put all this file's on the flash?with boot?what tool you use? under the pvb you can find one ic with number's:A82C250?it's ic with 8 nleg's and like as eeprom....lookink and tell us.....
its 29f200 flash on the left side of the cpu

[antwnhszr]

i ask you somethink else m8...............do you see any ic like that on the ecu?yes or no?

[258]

i ask you somethink else m8...............do you see any ic like that on the ecu?yes or no?
Hi,
No ic in this ecu , eeprom in the Flash 29f200bb,

[258]

how to put all this file's on the flash?with boot?what tool you use? under the pvb you can find one ic with number's:A82C250?it's ic with 8 nleg's and like as eeprom....lookink and tell us.....
With Boot Mode and external programmer

[258]

With Boot Mode and external programmer
Small update, i installed emulator changed line in eeprom and car work fine.
Thanks to all for help.

[Maxtechmk]

Small update, i installed emulator changed line in eeprom and car work fine.
Thanks to all for help.

Hi 258 i have same problem with clio2 1.4 8v i have emulator but dont know wich line to chanhe in eeprom can you sand me the file thnks.

[gwiazdamb]

Hi 258 i have same problem with clio2 1.4 8v i have emulator but dont know wich line to chanhe in eeprom can you sand me the file thnks.


You need to read the 29F200 flash make changes according to the instructions and save
Install the emulator and enjoy