MPPS v18 GOOD OR NOT?

[mircea13]

yes. fgtech does. my kess is dead due to tokens. but when it worked it did this cars over obd (kline) .

[mircea13]

did some of you writed before this kind of ecu on can ? my problem is that can protocol is verry slow. i did a read on the a6 c6 over can an it took 14 min for 2mb file. file seems to be ok, but won't try to write it. i can't remove the ecu from the car because on most of the audi there is metal bracket holding the ecu , and the customer won't let me drill it out, in order to take ecu off and make a bdm back-up in case the wtite fails.

[edd79]

Hi, I am trying to write mpps v18 to psg16 opel zafira 2.0dti. Firstly is it normal that is says checksums 10 corrected 2 ? is this ok? the file is not checksummed on winols.And secondly it says : REQUIRED TIME DELAY NOT EXPIRED and wont write? Do i need to leave the pump connected with power to MPPS for an hour or so before writing? real stuck thanks

[kukukatsu]

did some of you writed before this kind of ecu on can ? my problem is that can protocol is verry slow. i did a read on the a6 c6 over can an it took 14 min for 2mb file. file seems to be ok, but won't try to write it. i can't remove the ecu from the car because on most of the audi there is metal bracket holding the ecu , and the customer won't let me drill it out, in order to take ecu off and make a bdm back-up in case the wtite fails.

mate.. dont ask client to drill metal bracket, just do it. thiefs can do immo off by obd without drilling... And if you fear to try write so its not job for you...

[mircea13]

would you write it if you know it could get wrong resulting in a bricked ecu and you don't have a bdm backup ? seen dozens of cars f***d up like this .

[2200]

I don't see problem at this ecu.
i always read eeprom first over obd. VagDash
Than tune over obd. If some problems, than it is bdm time, but never had problems.
tool was fgtech v54.

if you have more tools try read with all tools just to have right ori files if you will need to recovery over obd if possible.
regards

[mircea13]

i don't have vag dash can. but i will buy one in the near future.

[2200]

And by the way.
k-line ist faster but can is safer.
if you do over kline attach a battery charger 13v

regards

[mircea13]

thanks man! i would have a try .

[fabiof1]

Hello everybody.

i have basic question.
There is really a difference between the mpps v18 china and mpps v18 Europe?
Or same ???
Thanks for your help

[edd79]

OK so, psg16 zafira, read, write OK checksums 10 corrected 2 is normal. Let mpps do checksums nothing else. If security timeout error wait an hour powered up and try again. Then try immediately again and worked. EU v18

[med2132]

j ai deja utilise mpps v18 clone europe c bon

[med2132]

verry good

[mircea13]

tested on a4 b6 2005 1.9 tdi BKE edc16u31 ,found ecu on kline read write ok over kline.disconect fan plug when writing.

[kukukatsu]

As i remember there is no need to disconnect fan... all mercedes needs to disconnect fan

[mircea13]

better safe than sorry ;) done one(A4 B6 edc15p+) last week and fan went on when it erased the flash. the fan control module in the absence of any message from ecu goes in faulty mode and spins the fan at full speed consuming 12-15 amps . that's why all the tools suggest using a charger .

[smirnoff_rules]

anyone who remaps without battery supply on is asking for trouble

[smirnoff_rules]

anyone done ford dmc3.5 mpps ?

[carmageddon]

yes, R-W-CHK without problem (many kuga and smax, i work 3-4 days in ford dealers)

[tehnosoftex]

Yesterday I try focus 1.6 edc16c34.5 euro5 and failed. It reads ok but when try to write, it goes to 100% and after that it writes transfer aborted and car was killed. I resuscitate it with vcm2.

[catala20032004]

i wrote edc16c34 on ford many times. all ok. ive left ingition off 2 min after so i dont get reflash error and all went ok. but my mpps is eu clone the purple one

[catala20032004]

ive even made some edc17 vag golf 6 via obd. it took 30min to make the cheksum but all ok

[smirnoff_rules]

Yesterday I try focus 1.6 edc16c34.5 euro5 and failed. It reads ok but when try to write, it goes to 100% and after that it writes transfer aborted and car was killed. I resuscitate it with vcm2.
is this one of the first clones or you get it afew months back ?

[morfej]

Opel Astra H 2010 Z19DTR with Denso MFDX, r/w without a problem, also checksum corrected by MPPS.

[manijakaz]

Opel Astra H 1.7CDTI 125PS (98002895 Z17DTR DENSO) - R/W OBD(CAN)- ok.
207 edc16c34 Can R/W
ducato edc16c39 RW ok
cosra z10xep bosch med1.1.5 r/w , write in slow only
Astra H Denso Z17DTJ R/W CAN - ok
SEAT ME7.5.10 R/W k-line (cat_off) - ok
Magneti marelli 6F0 full read/write by OBD MPC,Flash EEPROM OK!
Golf 1.6 TDI Siemens Simos Pcr2.1 R/W can (unlock boot mode-ok) - ok
Corsa 1.3cdti marelli mjd6 reads writes ok
OPEL Signum PSG16
2.2CDTI readout as a Zafira.
all OK.


mitsubishi pajero 3.2l did denso 4m41 R/W ok (chinese)
suzuki vitara hdi edc15c2 R/W ok
EDC17C10 PSA boot mode Read OK
Golf TDI EDC17c14
a4 2.5L edc15v obd read and write
1.9SDI EDC15V+ .... generic eeprom OBD K-line R/W-OK Flash OBD K-line R/W-OK
Polo SIMOS 3PE 1.2 12v read/write as generic simens SIM4LE boot mode flash 512kB - OK (catalyst off).
ford edc16c34 2.20 r/w ok
Mazda 6 2.0 MZR-CD 110hp Denso RF8G- OBD R/W - OK
Opel vectra C, PSG16 can, direct conexi?n to pump,read-write-cks, all Ok.
Simos Pcr2.1, obd read-write-cks ok.
mazda cx7 2.2 170 ecu denso dont ok read 4% after error
Lacetti (2008y) 2.0 CDRi EDC16C39 R/W CAN (only map 2Mb) as Captiva = OK
BMW e91 330xd edc16c35 R-W OK China clone
Astra vxr me7.6.2 R/W OK ( do that ecu own risk ! )
Fiat Doblo 1.3 mjet mjd6f3 obd - r/w ok
Range Rover edc17cp11 boot - r/w ok
Corsa D 1.3 CDTI, EDC17C18, 70.0kw,2010, Z13DTE R/W bootmode TriCore™ = OK
GOLF V 1.6 FSI, MED9.5.10, OBD/CAN R/W ( 30 minutes) = OK
Kangoo EDC17C42 bootmode TriCore R/W = OK
Alfa Romeo EDC16C39-5.5 CAN, ok perfect
Eeprom R/W and Flash R/W on VW Golf EDC15P worked perfectly with 70€ V18 from eBay
SID305 BOOT sak1766 read - write Ok
Ford Fusion 1.4 TDCi Siemens Sid 804 R/W OBD CAN = OK
MED17.4 peugeot 207 read write ok
astra h 1.9 tva off OBD and Zafira B 1.9 EGR off OFF ok
simos pcr 2.1 R/W obd ok
Volkswagen Passat 2.0 TDI Siemens PPD 1.X R/W OBD/CAN = OK
Ford Fusion Style 1.6 TDCi Bosch EDC16C34-2 ok
Read written FLESH + MPC + EEPROM fiat marely 6f3, OK through OBD.
Fiat Stilo IAW6JF.P3, through OBD, mpc and eeprom read write for immo-off, all ok.
Linea 2011 Marelli 6F3 read/write OBD Trought K-line,
peugeot 807 ECU DELPHI DCM 3.5 READ OBD OK
Fiat Scudo as (Peugeot 3008) 2.0 HDI Delphi DCM 3.5 R/W OBD/CAN (CRC=OK) = OK
citroen c5 DCM3.5 read write OBD ok, checksum ok
ME7.3.H4 boot mode read /write full OK
Opel cdti 1.7 ecu Denso R/W ok


Suzuki SX4 DDIS 1.9L 120hp, Bosch EDC16C39 2008, can & kline, read & write by obd ok.
opel corsa 1.3jtd MT marelli ecu 6J0 C1,read/write true obd=ok
Audi a4 edc17cp14..read... write obd ok.
NISSAN Q. EDC16CP33 (4A44383842) R/W OBD = OK (CRC-OK).
Jetta 2,0 16v TSi 200cv - MED17.5.2 Tprot10


Read in Boot = OK
made OBD unlock and CKS by MPPS, write boot = OK
tested edc16u1 from T5 2007 1.9tdi AXB 77kw. read write ok over obd on kline.
edc17 vag golf 6 via obd. it took 30min to make the cheksum but all ok


Opel Astra H 2010 Z19DTR with Denso MFDX, r/w without a problem

[dorofteius]

Yesterday I try focus 1.6 edc16c34.5 euro5 and failed. It reads ok but when try to write, it goes to 100% and after that it writes transfer aborted and car was killed. I resuscitate it with vcm2.

This car only bdm. Rsa protection . So no chance by obd right now. At least not with any tipe clones.

[twchnodictator]

Hi mates,

EDC17CP14 VAG (golf 6) is it safe to make via OBD?

[smirnoff_rules]

Hi mates,

EDC17CP14 VAG (golf 6) is it safe to make via OBD?

i think TPROT is from sw1037515000 up so below that and no updates at dealer should be ok

[twchnodictator]

i think TPROT is from sw1037515000 up so below that and no updates at dealer should be ok
Tried to read via OBD. Can't read.
Via boot tricore also no luck. Galletto also failed. Can't understand what is the problem. Car was in the dealership not so long ago with updates caused by dieselgate scandal. Could it be the reason?

[smirnoff_rules]

bootmode should work regardless of update and id with obd too

you havnt said what year car is could be gtp connections

[twchnodictator]

bootmode should work regardless of update and id with obd too

you havnt said what year car is could be gtp connections

2009 production year

[smirnoff_rules]

tuning protection started 2009 and above so l wouldnt obd flash it , boot should worked fine are you using resistor or straight to boot cable ? l would use 1000ohm to boot cable and green to pin 87

[twchnodictator]

tuning protection started 2009 and above so l wouldnt obd flash it , boot should worked fine are you using resistor or straight to boot cable ? l would use 1000ohm to boot cable and green to pin 87

I used 1000 ohm only only boot pin, exactly how it was in galletto tutorial

[smirnoff_rules]

l use grey boot wire to resistor to ecu on edc17c10 dosnt even need resistor
l use ktag 99.9% off the time tested mpps last year
my mpps pinout folder says dont use resistor

https://i.gyazo.com/de438cdc859ccec5d1c3ce86d4c95370.jpg

[tinaca]

sorry for my bad English
but if it is purple clone v18 I already made several without problems

[tinaca]

[QUOTE = twchnodictator; 3099624] Hi mates,

EDC17CP14 VAG (golf 6) é seguro fazer via OBD? [/ QUOTE]


sorry for my bad English
but if it is purple clone v18 I already made several without problems

[smirnoff_rules]

you only need to flash one with later s/w and you will have a very bad day

[zyjekrc51]

Audi A4 my2004 2.4V6 ME7.1 read/write via obd - OK

[zyjekrc51]

vectra 2.2 CDTI PSG16 read/write -OK

[zyjekrc51]

zafira Y20DTH PSG16 read/write - OK

[smirnoff_rules]

for the first time mine failed on an old vag edc16cp34 ? do lots of vag with it and no problems ? kess did no problem

https://i.gyazo.com/55cb0f1f915764c74e11a4e61e35efbb.jpg

[stevan]

Anyone try to remove U12 LM2903 (K line drv-in fact comparator IC) and install L9637D (I think much better K line driver) in place U8 ?

I have done it and on bench have no problem to get ID on EDC15 VW and IAW59F.

But not tested on Car.In fact i put back L2903 as it was .

I know that LM2903 was used for K line 10-15 year ago,now much better K line drivers are available.

[lucianh]

After 10 - 15 times write the interface becomes unusable... clone china.

I think the processor burns itself.
the interface becomes unusablePerhaps the processor burns itselfthe interface becomes unusablePerhaps the processor burns itselfthe interface becomes unusablePerhaps the processor burns itself

[mircea13]

i have v18 china and used for more than 50 times. no problem so far. mainly on vag edc15/16 , opel edc16c9/39 .this is best thing money can buy ;)

[Rhyno92]

for my experience:
Read\Write 7.3.1 alfa 147 1.6 OK
Read\Write 9GF fiat 500 2016 OK
Read\Write 59f.m5 Y 2005 OK
Read\Write 5AM Ducati s4r 2005 OK

NO CONNECTION WITH delphi DCM 1.2(r&w with galletto)

[dritan]

Fiat Iaw 59f×× read write by obd or on bench ? did it maked the checksum ?

Sent from my GT-I9301I using Tapatalk

[Rhyno92]

Fiat Iaw 59f×× read write by obd or on bench ? did it maked the checksum ?


BENCH ... there is a button for checksum but i think i obd is the same.

[H.Wessel]

Last week it broke a ME7.5 from a passat 2003, one of the newest with 28F800, it delete flash but can not write by obd, I repaired with galletto, so be carefull with this ecus and mpps.

Regards

[smirnoff_rules]

did Volkswagen Tiguan 3.0 petrol me7.1.1 and wasnt any problem , first batch mpps18 , its been a great tool

combo 1.3cdt mj60 something worked fine , sid802a peugeot read and right with can

[cristyand]

Hy,
did anyone manage to read ecu from Mazda CX7 2.2 MZR-CD 173hp Denso R2AX ?

[stevan]

W211 2003 2.2CDi EDC16 ......invalid key error.

Poslano sa mog ZTE Blade V6 koristeći Tapatalk

[leaf]

This car only bdm. Rsa protection . So no chance by obd right now. At least not with any tipe clones. i did same car yesterday with no problem but of course i made bdm first just in case . but obd read write all good

[mircea13]

did you guys read eeprom with mpps v18 from 1.3 cdti mjd 6jo ecu ? need it for carpass to make a key .

[spychu14]

yes. First make backup of injector coding bcs after read eep it will be gone :)

[tarabostesul]

Fiat Iaw 59f×× read write by obd or on bench ? did it maked the checksum ?

Sent from my GT-I9301I using Tapatalk

read write obd ok iaw 59f hw103
read 20 min write 3min
read 320kb
18120MZ.Bin.Bin

[bocaje]

hello.
EDC16C2 W203 mercedes mpps v18 EU CLONE not work ...

regards

[PaoloDigital]

I try but chinrese

[PaoloDigital]

not worl is fake

[mikroel]

For what purpose exactly used resistors R14 and R114 ?I have 102 value and my mpps v18 working well ,r/w everything without problem but i saw that some variants use value 511 .


Sent from my iPhone using Tapatalk

[tiugrikas]

vectra 2.2 CDTI PSG16 read/write -OKHi did you read write by obd ? Cause mine only read by obd but no write and i dont know why

Išsiųsta naudojantis HUAWEI TIT-L01 Tapatalk 4 Lt

[Faraday]

did Volkswagen Tiguan 3.0 petrol me7.1.1 and wasnt any problem , first batch mpps18 , its been a great tool

combo 1.3cdt mj60 something worked fine , sid802a peugeot read and right with can




I killed me7.1.1 a8 d3 4,2l with v18 It reads ok but can not bypass security and kill ecu in writing.

[stevan]

I try excange u12 with si9241A , not work , you are 2 version pcb , and 1 problem stability tension on k-line and can line , mod your mpps with this link:


https://www.linkedin.com/pulse/mpps-v18-ecu-china-clone-pcb-rework-kent-elsa

http://ecuprogram.webstarts.com/blog/post/mpps-v18-ecu-china-clone-pcb-rework

Are 2 pcb 20160905 and my 20170211 , differentYou must solder K line driver in empty U8 place not in U12 where is Lm2903

Poslano sa mog ZTE Blade V6 koristeći Tapatalk

[stevan]

I try excange u12 with si9241A , not work , you are 2 version pcb , and 1 problem stability tension on k-line and can line , mod your mpps with this link:


https://www.linkedin.com/pulse/mpps-v18-ecu-china-clone-pcb-rework-kent-elsa

http://ecuprogram.webstarts.com/blog/post/mpps-v18-ecu-china-clone-pcb-rework

Are 2 pcb 20160905 and my 20170211 , differentNote that U8 pinout is not for Si9241,compare with L9637d and will see difference,RX,TX,VCC...

Poslano sa mog ZTE Blade V6 koristeći Tapatalk

[mb7361]

buy original if u work

[PaoloDigital]

I solded in U8 , i check pin pcb with pinout si9214a datasheet , and removed L.03.. U12 , but not work, i tested also with 2, i resolded Lm2903 and mod ocb ...2017.. as 2016 .. and work read and writw 59f under 100 , but nor 59f over 100. I wont now replace L2903.with L9637d thank

Original schematic is not as clone. different



You must solder K line driver in empty U8 place not in U12 where is Lm2903

Poslano sa mog ZTE Blade V6 koristeći Tapatalk

[PaoloDigital]

You are differente from lm2903 and L9637d ? Lm9637d go to U8 if replace lm2903? thank

[maybach_]

Hi mates
I have a V18 Clone and want to read my Berlingo ECU with EDC17C10 but can't see whare are the meny for EDC17 ecu
can someone help add video or foto how to do :hmmmm2:
Thanks in advance

[DR Race]

Hy guys, just a stupid questions from me, I am new to using mpps v18 ,I have buyed one to play with, how can I check TP level on edc 17 vag???

Trimis de pe al meu SM-G930F folosind Tapatalk

[tarabostesul]

peugeot 307 1.6 edc16c34 read write obd..ok

[zyjekrc51]

HI!
YES READ/WRITE by OBD
some other PSG16 I had to read and write directly via connector on PSG16 because by OBD no connection established.

[zyjekrc51]

Hi did you read write by obd ? Cause mine only read by obd but no write and i dont know why

Išsiųsta naudojantis HUAWEI TIT-L01 Tapatalk 4 Lt


HI!
YES READ/WRITE by OBD
some other PSG16 I had to read and write directly via connector on PSG16 because by OBD no connection established.

[DR Race]

hy guys .can somebody check a file for me .i am new on mmps,i have no win ols but i think this car is already tuned ,thenks in advance!!

[mysterious]

hy guys .can somebody check a file for me .i am new on mmps,i have no win ols but i think this car is already tuned ,thenks in advance!!


No, car don't tiuned, this is most similar ori file

[DR Race]

No, car don't tiuned, this is most similar ori fileFile look ok ??? First time using this mpps !


Trimis de pe al meu SM-G930F folosind Tapatalk

[mysterious]

Try read with another tool and I will compare

[tiugrikas]

HI!
YES READ/WRITE by OBD
some other PSG16 I had to read and write directly via connector on PSG16 because by OBD no connection established. yes I tryed write via connector with two vectra c but still no result and also cant read write audi vw edc17 anyone has experience with it too ?

[sdtsedat]

Hi mates
I have a V18 Clone and want to read my Berlingo ECU with EDC17C10 but can't see whare are the meny for EDC17 ecu
can someone help add video or foto how to do :hmmmm2:
Thanks in advanceEdc17c10 always bootmode.

Verstuurd vanaf mijn SM-A520F met Tapatalk

[extremebike]

Hello to all,
I have a problem on my V18 china.
it worked great until now.
since yesterday, the sw starts, everything works,
but can not find more ecu (kline or can)
does anyone have a fix for the components?

[poxxxy]

hello.
EDC16C2 W203 mercedes mpps v18 EU CLONE not work ...

regards

W639 Vito EDC16C2 MPPS V18 doesn't work either, invalid seed key. Had same on a Golf MK5 GT BKD 2.0 TDI too today which is odd :) (2005).

[fabiof1]

Hi I'm looking for a notice edc17cp14 with Mpps v18 EU Experience? Possibility obd? Boot?
Thank you

[tarabostesul]

view post nr 459..

[fabiof1]

Ok thanks.
but how to make for tprot level ? If active or not ?
I know that with an original kess in obd wrote it and it detects the level of the tprot.


But mpps?

[teamtuner]

Ok thanks.
but how to make for tprot level ? If active or not ?
I know that with an original kess in obd wrote it and it detects the level of the tprot.


But mpps?
use only boot mode

[fabiof1]

Yes I think...
but just for read ecu no problem in obd with Mpps...

[fabiof1]

Latest question....
Mpps v18 Europe ( Carprog eu )
what is better clone :
kess v2 5.017 / or / Mpps v18 ......
I would like Your opinion .

Thanks ;)

[DR Race]

Latest question....
Mpps v18 Europe ( Carprog eu )
what is better clone :
kess v2 5.017 / or / Mpps v18 ......
I would like Your opinion .

Thanks ;)I saw last week one kess v2 ""EU clone " from car prog, it looks just like China red kess , I think it is a China clone Reworked, eu clone are indifferent, on the eu clone you don't have green or blue led , you have another pcb , I don't know what to say , last week one friend buyed from car prog and it is China!!!

Trimis de pe al meu SM-G930F folosind Tapatalk

[fabiof1]

Yes real clone Europe it is good.
but kess v2 or mpps v18 when it is better ???

[OVERSPEED]

Kess has more cars but MPPS is much more stable in cars that it can do...

[fabiof1]

Ok thanks.

And only read ecu edc17cp14 with obd it is possible ? No risk ?

[vasco fernandes]

Kess has more cars but MPPS is much more stable in cars that it can do...

and mpps is better recovery mode

[fabiof1]

Ok thanks for your opinion.
I'll try to read an edc17cp14 by obd ...

[nbtechnic]

Warning: the use of clone mpps with risk and peril, I already made the expense with this clone tool. I give up its use. Here is my bad experience: ecu blocked with mpps v18 clone: edc16c34, marelli mjd8f2. Yet it worked well when I bought it, I'm disappointed ... I bought 2 new ecu for my cars.

[fabiof1]

��
clone china ? Eu pcb purple ? Or Carprog ?

[boomeer]

Warning: the use of clone mpps with risk and peril, I already made the expense with this clone tool. I give up its use. Here is my bad experience: ecu blocked with mpps v18 clone: edc16c34, marelli mjd8f2. Yet it worked well when I bought it, I'm disappointed ... I bought 2 new ecu for my cars.
:hmmmm2::hmmmm2: That 2 ecu have bdm on board !!! how can you kill it by obd ? you need more practice and then no need buy 2 ecus!

[fabiof1]

Strange Yes... how it happened?

[nbtechnic]

When writing ecu, the usb connection to move, writing to failed
I made an attempt of recovery with the MPPS, at the end of the writing the cars did not start anymore,
I try by bdm but ecu does not respond, that's why I decided not to use the mpps china.

[nbtechnic]

With the new ecu, edc16c34 by obd and boot pin + BDM; marelli MJD8F2 by JTAG; I now use Fg v54 (test with 0386 and 0475) without any problem.

[meteor80]

Does someone have solution to repair MPPS V18 with "waking up ECU error"?
Program starts,
Voltage recognize OK.
But no communication with ECU.

[nbtechnic]

all these problems leads me to think that the mpps is planned for a certain number of use, after this number to exceed it does not work, but without which one realizes it ...
mine also worked very well at first, until he made me believe he was doing a recovery my ecu, but it was completely wrong.

[catala20032004]

Any advise on wich model is best? red pcb or purple pcb? ive seen red pcb is cheapper than the purple

[bocaje]

Hello.
Can anyone confirm if it EU clone works on Renault SID301 or SID304 or SID305?
If not best solution?


Regards

[juse]

Any advise on wich model is best? red pcb or purple pcb? ive seen red pcb is cheapper than the purple

I'd say its kind of lottery. Seem there are people who sell china crap as made in eu and with stupid high price. China factory can make good quality too, if paid for that.

[DR Race]

Any advise on wich model is best? red pcb or purple pcb? ive seen red pcb is cheapper than the purpleRed most of them are China, purple pcb has good components and by my purple pcb is with gold circuit, till now done many car from 2000 till 2014 no problem by purple !
Red one you are not 100% if eu oder China, in moment I have saw China red sold as eu clone , buy inside is China!
Seller make 2 stickers with warranty if you want to look inside you have to.brske them, then probably inside is China pcb, a honest seller has no sticker an you can look inside !https://uploads.tapatalk-cdn.com/20180317/aa9cb6a952b6138fb16727de671af1e0.jpghttps://uploads.tapatalk-cdn.com/20180317/5a1e87fea69d9d656d4b87ab127e73c5.jpghttps://uploads.tapatalk-cdn.com/20180317/843d208d39034e68b9c924bf06a13e85.jpghttps://uploads.tapatalk-cdn.com/20180317/68ce31f3b07846ddb97df63c19f0db0e.jpghttps://uploads.tapatalk-cdn.com/20180317/a4a9a677d23858e4ceb241ad65a713c9.jpg

Trimis de pe al meu SM-G930F folosind Tapatalk

[juse]

Just wondering when all the chinese clones too come with purple pcb.. Is the original purple too? Carprog claimed that his reds were full eu too, wich seems to be false claim.

[DR Race]

Just wondering when all the chinese clones too come with purple pcb.. Is the original purple too? Carprog claimed that his reds were full eu too, wich seems to be false claim.Cp2010 is a good seller , he has a lots of good rewiew, I have never buyed from them.but on every forum good rewiew!

Trimis de pe al meu SM-G930F folosind Tapatalk

[juse]

Cp2010 is a good seller , he has a lots of good rewiew, I have never buyed from them.but on every forum good rewiew!

Trimis de pe al meu SM-G930F folosind TapatalkMight be, this was question about the eu clone, are the purple only one? http://car-prog.com/ has red pcb, tool costs 749e and there is written that made in germany. In other topic cp2010 wrote that red is made in china?

Lähetetty minun SM-A520F laitteesta Tapatalkilla

[DR Race]

Might be, this was question about the eu clone, are the purple only one? http://car-prog.com/ has red pcb, tool costs 749e and there is written that made in germany. In other topic cp2010 wrote that red is made in china?

Lähetetty minun SM-A520F laitteesta TapatalkillaEu Clone ar purple and olsow red pcb red pcb, you can see the difference from red China and red eu , component are different , eu red made has good components on pcb , if you trust seller you can buy or not , or buy China or original tool !

Trimis de pe al meu SM-G930F folosind Tapatalk

[juse]

Maybe cp2010 joins in and shed some light on the subject?

[obd2exe]

I just bought MPPS red PCB eu clone from carprog. Iwill post results on how it works

[rh03]

I just bought MPPS red PCB eu clone from carprog. Iwill post results on how it works

me too, it will happen the next days

[bocaje]

Hello
Can anybody help. Edc16c35 bmw safe with mpps v18 eu clone??

Regards


Enviado do meu iPhone usando o Tapatalk

[rh03]

Hello
Can anybody help. Edc16c35 bmw safe with mpps v18 eu clone??

Regards


Enviado do meu iPhone usando o Tapatalk

A friend to me do that with mpps v16 china ^^, but galletto or kess are better on this ECU

[SALAS]

Hello
Can anybody help. Edc16c35 bmw safe with mpps v18 eu clone??

Regards


Enviado do meu iPhone usando o Tapatalk

No problem.
I have done several times EDC16CP31-35 with MPPS V18 just make sure you have 14v with an external charger.

[bocaje]

Thank you
Its a esc16c35 from 2.0 bmw its the same is it??

Regards


Enviado do meu iPhone usando o Tapatalk

[SALAS]

Thank you
Its a esc16c35 from 2.0 bmw its the same is it??

Regards


Enviado do meu iPhone usando o Tapatalk

Yes is the same just make sure of the type of ECU some models from 2007 onwards have EDC17.

[juse]

I just bought MPPS red PCB eu clone from carprog. Iwill post results on how it worksWorks ok?


Lähetetty minun SM-A520F laitteesta Tapatalkilla

[juse]

me too, it will happen the next daysWorks ok? Have you looked inside?

Lähetetty minun SM-A520F laitteesta Tapatalkilla

[tiugrikas]

Hello
Can anybody help. Edc16c35 bmw safe with mpps v18 eu clone??

Regards


Enviado do meu iPhone usando o Tapatalk
I made this type of ecu bmw 730d 2006y withs mpps 13 worked perfect so I think most tools can do this ecus

[rh03]

[QUOTE = jus} 3252945] Ça va? Avez-vous regardé à l'intérieur?

Lähetetty minun SM-A520F tapis de course Tapatalkilla [/ QUOTE]

I don't tryed it, and i don't want open it sorry, I bought only for me7/edc15 and its recovery fonctions

[Kic]

China MPPS V18 (V18.12.3.8 - Tricore cabel version)
Opel Astra H OPC (Z20LEH) Bosch ME7.6.2 ECU
OBD Read OK
OBD Write Fails on 4%, recovery not possible with MPPS!!!

Managed to bring it back to life with Tech 2 SPS via OBD... So no issues regarding communications or faulty wiring.

[carmageddon]

the problem is bosch ME7.6.2 opel not the tool, also genuine tool fail with this shit ecu.

[markez12]

v18 is good. i have and im happy. Make ecu on list
I have and I'm happyI have and I'm happyI have and I'm happy

[Kic]

the problem is bosch ME7.6.2 opel not the tool, also genuine tool fail with this shit ecu.
Well, a cloned Tech 2 managed to re-flash a bricked ECU so i would say that the problem is in the tool not the ECU.
I know for a fact that EDS Motorsport IPF writes these ECUs reliably.

[carmageddon]

i have used all genuine tools for this ecu (and all clone too) and the problem is in the protocols of the ecu.
alien, dim and others, when released this protocols have warned all users for this problem...but many user try to reflash it anyway...6 time on 10 the ecu was bricked, all tuners know this

[DR Race]

Well, a cloned Tech 2 managed to re-flash a bricked ECU so i would say that the problem is in the tool not the ECU.
I know for a fact that EDS Motorsport IPF writes these ECUs reliably.Problem is not you tool, this ecu type has a problem, I checked this ecu with original kess , and when I chose this ecu type , kess pop up warning about this Ecu, protocole not reliable, I guess you was lucky with your Tech 2!
Kess let me read this ecu but every time with warning!

Trimis de pe al meu SM-G930F folosind Tapatalk

[tarabostesul]

caddy 1.6 .. simos pcr 2.1 ..read write obd ok..eeprom already unlocked..

[OVERSPEED]

MED17.2 Mini CKS not good, write OK on Boot

[Kic]

China MPPS V18 (V18.12.3.8 - Tricore cabel version)
Opel Astra H OPC (Z20LEH) Bosch ME7.6.2 ECU
OBD Read OK
OBD Write Fails on 4%, recovery not possible with MPPS!!!

Managed to bring it back to life with Tech 2 SPS via OBD... So no issues regarding communications or faulty wiring.

Let me correct my statement.

MPPS can flash this ECU but you must NOT use the latest OEM software update/revision.
Older file versions work OK, latest update has an few additional lines of code, maybe some rudimentary tuning protection.

Anyway my ignition cut mod is finally on the car.

[gazvts]

it's the write times on this ecu on most tools but mpps v21+ has faster write time has option eeprom backup

[OVERSPEED]

Yesterday made an Passat MED17.5 ECU in boot, allways made cks by OLS, but this time try only MPPS, and it didnt´work, car start but stall, and tbi stays cicling, KESS could not make recovery, make CKS by OLS and everything was Ok.

So my advice is not to trust 100% in CKS on MPPS V18

[tarabostesul]

fiat ducato mjd8f3..read write obd ok..write 2 min

[Faraday]

This is well known that MPPS will f-up CHK on m-ed-c17 ( I mean clone)

[cawadany]

Someone has tested on Fiat / Alfa 1.4 multiair Marelli iaw 8gmf?

[dudus8]

Hello,
Does anyone have any experience with MPPS V18 EU Clone with Peugeot 308 1.6 hdi 109 PS 2010 year 9HZ- Bosch EDC16C34
Can you safely read and save by Obd?
Regards

[figani]

hi, does anyone handle it to read and write direct over OBD a Mercedes-Benz BOSCH ME 2.1 (there is NO round connector under the engine cowling)....

does I have to connect PINS on OBD port...?

[donesko]

v18 deletes injector codes on marelli fiat&opel 6O3 , 6O2 even when only ID

[Panathaole]

Hi

that happens to me to...(lost injector code-easy to fix with mes if you already have read the code first) on marelli 6F3 with clone mpps v21...can't read flash... get error , read only eeprom and micro, very fast for obd tool... i am afraid to test it in other car, the only thing i have in mind now is the battery voltage.... i want to try with charger on battery, the tool shows me ~12.40v but mes ~11.60v maybe that is the problem....
i test it in the same car and let you know..


v18 deletes injector codes on marelli fiat&opel 6O3 , 6O2 even when only ID

[101newbie]

anyone has a pinout (tricore) for MPPSv18 clone for BMW EDC17 ? (read that you can use them same as ktag)

[Panathaole]

You can use pinout from fgtech galletto ......

[pulsar2000]

Hello,
Does anyone have any experience with MPPS V18 EU Clone with Peugeot 308 1.6 hdi 109 PS 2010 year 9HZ- Bosch EDC16C34
Can you safely read and save by Obd?
Regards
NO PROBLEMS !

[chaoui05]

Hi ,
How to r/w Simos 8.5 Audi ?
Thks.

[figani]

I used V18 for a Magneti Marelli Fiat 6F3... on bench... multiboot option...

flash... successful...
mpc... successful...
eeprom... failed...

open it and read it by Ktag... and compare it...

v18 corrupt data from eeprom...
read 5 x eeprom by V18... everytime another result...

[cawadany]

Eeprom can change for different dtc stored.

[fricker]

Hi, mpps18 Grey boot wire where is connected on odb2 socked side ? my china cable is not soldered

[teerak2uk]

Hi, mpps18 Grey boot wire where is connected on odb2 socked side ? my china cable is not solderedOn 4 or 5. .

[Panathaole]

I used V18 for a Magneti Marelli Fiat 6F3... on bench... multiboot option...

flash... successful...
mpc... successful...
eeprom... failed...

open it and read it by Ktag... and compare it...

v18 corrupt data from eeprom...
read 5 x eeprom by V18... everytime another result...



Hi

you use clone?

if yes is China or EU clone?

[carmageddon]

I used V18 for a Magneti Marelli Fiat 6F3... on bench... multiboot option...

flash... successful...
mpc... successful...
eeprom... failed...

open it and read it by Ktag... and compare it...

v18 corrupt data from eeprom...
read 5 x eeprom by V18... everytime another result...

i did mj6 and mj8 via obd with mpps multiboot, never on the bench...no problem

[figani]

Yes, 100% clone... Bought it before years as reworked...

I had only ecu, not car... I read flash/mpc also several times... Each time same... Only Eeprom was not same... Why... Really don't know... :upset:

[Panathaole]

Yes, 100% clone... Bought it before years as reworked...

I had only ecu, not car... I read flash/mpc also several times... Each time same... Only Eeprom was not same... Why... Really don't know... :upset:



well i read on bench over 10 times (and write a couple) the eeprom of one marrelli 6f3..... always with success...


and i compare the files..... you have right..... always a bit different like count something.. (44,45,46 etc) but only that different....




580169

[figani]

It's maybe a counter... :applause:

As I wrote, after that open it and read by Ktag, several times... Every time the same...

At the end... Solder down Eeprom and read it...
Compare with Ktag, and same...

Compare it with V18, and not same...

[Panathaole]

Anyway, i have read-write many times eeproms of that kind of ecus, never had any trouble.....

i have a fiat right now, i read eeprom via OBD a couple of times to see if there any difference....

what difference you got comparing mmps and ktag eeproms?

is like the eeproms that i have upload?

[Panathaole]

Update for mpps v18 clone But NOT China..... eu clone.....

yesterday i brick an ecu....... read in boot mode flash,micro, eeprom.... all ok

i start one more reading of the flash for compare..... at the half of reading....... :beheaded: no connection with ecu?

the ecu now is dead..... marelli 6o3...... no connection with op-com no hearing of the pump.... a big F on dash...

that is Very sad for me..... i had a big respect for that tool.....

and i dont know if is possible to recover the ecu.....

i Guess not....:frown::frown:

[rh03]

Update for mpps v18 clone But NOT China..... eu clone.....

yesterday i brick an ecu....... read in boot mode flash,micro, eeprom.... all ok

i start one more reading of the flash for compare..... at the half of reading....... :beheaded: no connection with ecu?

the ecu now is dead..... marelli 6o3...... no connection with op-com no hearing of the pump.... a big F on dash...

that is Very sad for me..... i had a big respect for that tool.....

and i dont know if is possible to recover the ecu.....

i Guess not....:frown::frown:

Marelli ecu are capricious, the best way is to do full backup on bdm with ktag, then flash obd with kess or mpps

[Panathaole]

Thank you

I give a try....

I have take after brick a ktag backup...

And I have the backup of the mpps....


Thanks.......

[rh03]

Thank you

I give a try....

I have take after brick a ktag backup...

And I have the backup of the mpps....


Thanks.......

So I think you can recovery your ecu,

your ktag flash should be FFFFFFF.... , and your flash MPPS is ok, you should find the corrupted zone on ktag flash copy your mpps flash in this location, calc checksums and write the fixed flash with ktag.

[Panathaole]

i have exactly the same files (ktag & mpps) no ffffffff

the only difference are in micro... ktag gives me 513 kb and mpps 512, at the end of the file i have a few lines with ffffffff

no other different..

the mpps cut of the power of the pump and i don't know what else.... is like set the ecu to safe mode.....

and at the end of reading , just recover the ecu....

now is like i have the ecu in safe mode .......without any driver load....

[PaoloDigital]

Hello Friand, Merry Cristmas for all.

I bricket blockjed my v18 ,whith used software v21 , not reconize to pc . lock!! , you have file firmware to reflash Cf8051 ... , i not finded cf8051 flashed recange, thanks for any response.

[bignslow]

Hey guys, I have MPPS V18 that I am suspecting has an internal short. Those who have one of these would you mind hooking up power to it and checking voltage on the Kline? I am getting 12 volts which I suspect is incorrect.

[PaoloDigital]

Hey guys, I have MPPS V18 that I am suspecting has an internal short. Those who have one of these would you mind hooking up power to it and checking voltage on the Kline? I am getting 12 volts which I suspect is incorrect.

You have zener diode on 12v , i removed D4 and D6

[kaadzis]

Hello, i have issues with v18 i cant conect to kline. can works fine. half year it worked perfect .can somoene help me? dont want to buy new tool.

[bignslow]

You have zener diode on 12v , i removed D4 and D6

So is it normal that I am getting 12 volts or?

[PaoloDigital]

I escange chip U8 vacum box , removed original , and rem removed diode D4 D6 , info in this post, or in forum , L..., integrate cirquit, enanced k line comunication,after blocked.

remove in U12 where is Lm2903

solder K line driver in empty U8 place not in U12!! :


L9637d solder in U8


have notice to file firmware , cf8051, unlock firmware ,thanks

[bignslow]

I escange chip U8 vacum box , removed original , and rem removed diode D4 D6 , info in this post, or in forum , L..., integrate cirquit, enanced k line comunication,after blocked.

remove in U12 where is Lm2903

solder K line driver in empty U8 place not in U12!! :


L9637d solder in U8


have notice to file firmware , cf8051, unlock firmware ,thanks

I didn't understand any of that.

[PaoloDigital]

I have done so You have to remove the integrated U 12 Lm2903;
and replace it with L9637d in U8
.Remove also the diodes D4 and D6.
These integrated that manages the k-line communication.Try. Image from web.



have notice to file firmware , cf8051, unlock firmware ,thanks

[fricker]

Hi, mpps18 Grey boot wire where is connected on odb2 socked side ? my china cable is not soldered

still need help

[teerak2uk]

still need helpProbably just to gnd pins 4/5

[PaoloDigital]

Hi, mpps18 Grey boot wire where is connected on odb2 socked side ? my china cable is not soldered

My mod video . to rework remake the alimentation of tricore , obd2 is standard , mpps color in sofware

https://www.youtube.com/watch?v=mcOvngdXpu4

[SALAS]

I made an Opel Zafira 2.0L with y20dth engine hybrid control unit PSG16.
Connect with the tricore cable CAN-L and CAN-H directly to the pump.

MPPS has read the PSG16 in 2-3 minutes, to write 7-8 minutes.
Make sure you have enough voltage when writing because the fan starts running (or disconnect it before write) if something goes wrong here you're f**ked.

MPPS calculates the checksum automatically all perfect.
I use MPPS v18 from China reworked.

[PaoloDigital]

no work fake cina

[bignslow]

I have done so You have to remove the integrated U 12 Lm2903;
and replace it with L9637d in U8
.Remove also the diodes D4 and D6.
These integrated that manages the k-line communication.Try. Image from web.



have notice to file firmware , cf8051, unlock firmware ,thanks

Where can I get the firmware and what do I use to flash it?

[rh03]

I made an Opel Zafira 2.0L with y20dth engine hybrid control unit PSG16.
Connect with the tricore cable CAN-L and CAN-H directly to the pump.

MPPS has read the PSG16 in 2-3 minutes, to write 7-8 minutes.
Make sure you have enough voltage when writing because the fan starts running (or disconnect it before write) if something goes wrong here you're f**ked.

MPPS calculates the checksum automatically all perfect.
I use MPPS v18 from China reworked.

can you share your wiring diagram for psg16 pump please ?

[PaoloDigital]

Where can I get the firmware and what do I use to flash it?

The firmware , not find in web , china not share, programmer is problem cf8051 bdm image in web .

[mancioks]

can you share your wiring diagram for psg16 pump please ?

https://www.digital-kaos.co.uk/forums/showthread.php/619693-conection-MPPS-V18-to-zafira-Y2-2DTR-PSG16?highlight=Psg16+mpps+v18

[SALAS]

Do not cut the green and white wires.
Simply make a cut around and join with the MPPS cables.

Ensure stable voltage during writing.

[fabiof1]

Hello, everybody.
Is there really a difference between the Mpps v18 Europe and Chinese ??
Thank you for your feedback

[Panathaole]

Hello, everybody.
Is there really a difference between the Mpps v18 Europe and Chinese ??
Thank you for your feedback

I don't know if they have any major difference in how they works, but I feel more safety by using eu clone....(they have different hw)...

[alkaskad]

Hi guys!
I have a strange problem with my MPPS 18. Tricore boot stopped working, it worked before on the same ECU, VAG EDC17 TC1796...
ECU is ok, because i tried to read it with Kess and Galletto and it works.
I asked tech support, but they say that is because i tried to update it via internet...

OBD works fine. Did someone had a similar problem?

[Panathaole]

Try reinstall the software....

It is an original tool?

[alkaskad]

No, it's clone. I tried with software reinstall, other computer, other usb cable, I've even made another breakout cable... But nothing made tricore to work...

[golfather2]

Hi all,

bought a 06A 906 018CJ M3.8.3 tried to flash it with v18, comes back with ERROR message. ECU programming Voltage Missing

Tried it with a v13 clone worked perfectly

Anyone else had issues with this ecu

[zzapp]

Hi there,
yesterday my Mpps stopped working, let me try to explain what's happened and maybe you guys will help me with this.
Always had installation folder on my desktop copied from cd included in my mpps v18 clone.
Always launched mpps.exe from that folder, and always worked fine
Yesterday I've used it to read a Fiat Idea mjd6f3, read all good
Then after I've edited the .bin file to remove egr/dpf I've launched again mpps.exe and suddenly the famous hated popup:"There has been a application exeption error"...
Then I've goggled this message and I've moved the installation folder to c:/mpps, made a shortcut on my desktop, but error keep on come out when i try to launch it
I've tried to launch with admin right too but still same prob
Installed on another partition win 7 64bit, but still same prob...
I'm out of ideas now, can you try to help me plz?
Tks a lot!

[Panathaole]

Hello, everybody.
Is there really a difference between the Mpps v18 Europe and Chinese ??
Thank you for your feedback


i have eu clone mpps 18 and never had any problem .... (one time i lock an 6O3 but caused by laptop not from mpps...)

i had buy one china 21 mpps and after i use it for ~ 10 times.... guess.....:beheaded:...... (before buying, i ask the china sheller for time bomb, and guess his answer... :biggrin: )

[dudus8]

Hello,
I have a question:
Have you tried reading or writing to Edc16C39 from Fiat / Alfa? How does mpps handle this Ecu?

Wysłane z mojego SM-G973F przy użyciu Tapatalka

[mancioks]

Hello,
I have a question:
Have you tried reading or writing to Edc16C39 from Fiat / Alfa? How does mpps handle this Ecu?

Wysłane z mojego SM-G973F przy użyciu Tapatalka

Read/write no problem! :)

[dudus8]

Read/write no problem! :)Have you tested it? I heard that there is a problem with this Ecu by obd. Not all maps are read, Kess reads this time for a long time - about 40 minutes

Wysłane z mojego SM-G973F przy użyciu Tapatalka

[mancioks]

I have done alfa/saab/opel edc16c39 and for me partial read is enough to do remap/dpf/egr/swirl and so on.

[dudus8]

I have done alfa/saab/opel edc16c39 and for me partial read is enough to do remap/dpf/egr/swirl and so on.How long does Mpps read and write to Ecu? Works stably? I have an Mpps V18 Eu Clone, what do you think? Will it be good for this Ecu?

Wysłane z mojego SM-G973F przy użyciu Tapatalka

[dudus8]

It is possible to read and write Alfa Romeo 159 2.4 jtd edc16c39 2007 year?

Wysłane z mojego SM-G973F przy użyciu Tapatalka

[mancioks]

It will be ok. If car has CAN it will be faster if not slow.

[dudus8]

It will be ok. If car has CAN it will be faster if not slow.Ok thanks for info.
Mpps v18 read/write this car via Kline

Wysłane z mojego SM-G973F przy użyciu Tapatalka

[dudus8]

Alfa Romeo 159 2.4 Jtdm R / W- Perfect. But I have a question:
Did someone Marelli MJ8F3 test with Fiat Ducato 2.3 Euro 5? Reading and writing possible by OBD? Checksum OK?

Wysłane z mojego SM-G973F przy użyciu Tapatalka

[zoro1]

WITH china clone read write ,iaw59 fiat ,MB edc15c,vw edc15vp/restore after bad chk file/!crafter edc16 -read,iveco edc16 read ,edc16 opel read,but alga 2,4 jtd 2003 -edc16 no read!!!!strange -bmw 320 2000cc year 2001 with bosh edc15c -mpps read only 64 -galleto 256kb.PSG16 opel -read write ok chk correc

[dorofteius]

Alfa Romeo 159 2.4 Jtdm R / W- Perfect. But I have a question:
Did someone Marelli MJ8F3 test with Fiat Ducato 2.3 Euro 5? Reading and writing possible by OBD? Checksum OK?

Wysłane z mojego SM-G973F przy użyciu Tapatalka

Yes all ok. I have done allot of them.

[dudus8]

Yes all ok. I have done allot of them.Checksum correct also OK?

Wysłane z mojego SM-G973F przy użyciu Tapatalka

[dorofteius]

Checksumm was already done with winols by my tuner.

[cawadany]

Someone has tested multiboot obd full read and write for FCA Bosch ME7.9.10?

[juse]

Mpps 18, List says Audi A7 edc17 all? Anyone done? Via obd?

[Panathaole]

Mpps 18, List says Audi A7 edc17 all? Anyone done? Via obd?


My opinion is to not play with edc17 by obd.... best way is bootmode, to grab all files...

[cawadany]

Someone has tested multiboot obd full read and write for FCA Bosch ME7.9.10?Nobody has tested it?

[OVERSPEED]

Someone has tested multiboot obd full read and write for FCA Bosch ME7.9.10?

In my country there is only ME7.9.10 K-line ECUs, but I tried and obvioulsy not worked..

[tictach]

Ebay seller NOT to buy from MPPS v18 kolsoltech201607 (https://rover.ebay.com/rover/0/e11051.m44.l1181/7?euid=042c8fe097894bd3ba1d463d266f02ea&bu=44991176729&loc=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fusr%2Fkolso ltech201607&sojTags=bu=bu)Shitty components and 97 % of them is wrong value or type .

[smokinjoe]

Ebay seller NOT to buy from MPPS v18 kolsoltech201607 (https://rover.ebay.com/rover/0/e11051.m44.l1181/7?euid=042c8fe097894bd3ba1d463d266f02ea&bu=44991176729&loc=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fusr%2Fkolso ltech201607&sojTags=bu=bu)

Shitty components and 97 % of them is wrong value or type .

Agreed,i purchased from this seller too as i thought it may be good quality coming from uk and i killed 2 ecus and laptop crashed so he sent me a replacement from china and still the same problems,tested on win7 32 and 64 bit.

[nexusjose]

Hi. Have you got some Picture with mpps wire edc17c50

[makadam]

My FG 54 does not read 6F3 from Grande Punto through OBD? Did u remove resistor?

[nbtechnic]

fgtech does not have any drivers for OBD playback, for magneti marelli; read and write by JTAG. CAUTION = if the fgtech is a china clone, the tablecloth JTAG is upside down from the factory (risk of damaging the ecu) so to check if the tablecloth is well made refer to the photos that are in the fgtech documents. Off subject closed...

[onejay10]

Ebay seller NOT to buy from MPPS v18 kolsoltech201607 (https://rover.ebay.com/rover/0/e11051.m44.l1181/7?euid=042c8fe097894bd3ba1d463d266f02ea&bu=44991176729&loc=https%3A%2F%2Fwww.ebay.com%2Fulk%2Fusr%2Fkolso ltech201607&sojTags=bu=bu)Shitty components and 97 % of them is wrong value or type .

This seller is not good! Late deliveries and lost items and poor quality products.

[Burnsi]

Hi, i wann buy a MPPS v18 EU programmer.
Can anybody recommend me a Shop wich sends to germany?
No China clones, only good EU stuff.

Thx

[Panathaole]

Hi, i wann buy a MPPS v18 EU programmer.
Can anybody recommend me a Shop wich sends to germany?
No China clones, only good EU stuff.

Thx

Goggle it......
I have mpps v18 from c@rprog....
Very good and cheep tool......

[Burnsi]

Goggle it......
I have mpps v18 from c@rprog....
Very good and cheep tool......
Thx, i'm in touch with him.
I saw alot of ecu cant be read by mpps, only write.
How i can do this cars? Do i need another Tool?

[115jtd]

kess+ktag+mpps

[Burnsi]

kess+ktag+mpps
Too much for Hobby.
Its OK when its save to use the China clones, but many ppl told me the China clone stuff will brick ecu.
I have a China kess here, but i'm afraid to use it.

[Stelaras26]

Chinese kess 5.017 is ok for its money ,2.47 version is not ok.Stick to 2.23
also a reworked 4.036 is a good solution too.

[Burnsi]

I have a Red pcb 5.017 with 2.47 Software.
Some ppl told me this clones are very dangerous to use and it will brick ecu.
This scares me to use it and this is why i go for a eu clone mpps.

[Panathaole]

With what cars you planning to deal with?
Mpps is very good for a few, kess for others, galletto can help you.....

What exactly planning to do?

[Burnsi]

Stage 1/2 egr off for vag, bmw, Mercedes, opel

[Stelaras26]

With what cars you planning to deal with?
Mpps is very good for a few, kess for others, galletto can help you.....



Any of this tools can get the job done,mpps is mostly for diesels but good for recovery too..I would buy it if i were you.

[Burnsi]

Any of this tools can get the job done,mpps is mostly for diesels but good for recovery too..I would buy it if i were you.Ordered a eu mpps v18 now.
And for my kess clone, i will rework it before i try it.

Gesendet von meinem Mi MIX 2S mit Tapatalk

[Burnsi]

Chinese kess 5.017 is ok for its money ,2.47 version is not ok.Stick to 2.23
also a reworked 4.036 is a good solution too.

where i can find the 2.23?

[rh03]

Hello guys, some months ago, with a friend I tried to read a Renault me7.4.6 by me7.x.x generic boot mode driver with mpps v18 eu, it readed it, but the hex file was 90% different as genuine ktag read, car don't started after mpps write, of course, started after ktag write.


So don't try this ecu !

[Panathaole]

Hello guys, some months ago, with a friend I tried to read a Renault me7.4.6 by me7.x.x generic boot mode driver with mpps v18 eu, it readed it, but the hex file was 90% different as genuine ktag read, car don't started after mpps write, of course, started after ktag write.


So don't try this ecu !



it is Europe clone (red pcb?)

682286

this one (red) have nothing to do with (green) China mpps v18....

[MI16rs]

Hi

Would the tricore cable only works whit mpps v18 or will work whit earlier mpps v13.02 ?

Thanks

[figani]

Hi

Would the tricore cable only works whit mpps v18 or will work whit earlier mpps v13.02 ?

Thanks



it depends what you are going to do with it...?
they are pure cables, there is no electronics installed (in the form of resistors, etc.)...

[caja88]

Anyone tried tprot patching???

[MI16rs]

it depends what you are going to do with it...?
they are pure cables, there is no electronics installed (in the form of resistors, etc.)...

It is for flashing on the bench .

[Panathaole]

It is for flashing on the bench .

I always use it to connect ecus on bench.....

[Helpmeplease196]

MPPS 18 reads and writes this for Car BMW 3-Series F31 2013 320d 8AT BMW F31 N47D20C Diesel Euro 5 184hp ECM Bosch EDC17C50

[caja88]

Volvo v40 1.9 ,edc15c3 cannot read over obd....in description says connect pin 7 of device to pin11 obd,i dont get it

[115jtd]

car has a k line for 11pin

[caja88]

car has a k line for 11pin
ok,how to connect it?

[caja88]

tricore cable,power it up and connect green wire to obd pin 11?or?

[rh03]

it is Europe clone (red pcb?)

682286

this one (red) have nothing to do with (green) China mpps v18....

Sorry I didn't precise, it's v18 EU from carprog

[caja88]

tricore cable,power it up and connect green wire to obd pin 11?or?

Update---reads and writes perfectly on this way

[caja88]

MPPS 18 reads and writes this for Car BMW 3-Series F31 2013 320d 8AT BMW F31 N47D20C Diesel Euro 5 184hp ECM Bosch EDC17C50
How?Bench?U use clone or genuine?

[Orchid70]

Yesterday made an Passat MED17.5 ECU in boot, allways made cks by OLS, but this time try only MPPS, and it didnt´work, car start but stall, and tbi stays cicling, KESS could not make recovery, make CKS by OLS and everything was Ok.

So my advice is not to trust 100% in CKS on MPPS V18

Also my experience MPPS V18 clone - V70 D5 EDC16C31 - checksum did not work and had to correct checksum in WinOls (not me that is =)

[Orchid70]

well i read on bench over 10 times (and write a couple) the eeprom of one marrelli 6f3..... always with success...


and i compare the files..... you have right..... always a bit different like count something.. (44,45,46 etc) but only that different....




580169


What nice small power source are you using Panathaole?

[thorino]

Mpps v18 does not work with Fiat Bosch M7.6.3 (make virgin). It only looks like does some work but really , does nothing. After programming success !!! immo status not changed and still "wait for security code". I bought it on ebay, a piece of bull shit made from second hand Chinese socks .

[Panathaole]

what mpps are you use? with china clone v21(after a few rounds later dead...) i could t read 6f3 flash..... very bad tool

i get a eu clone and works great...

[thorino]

I use china clone, now looking at eu clone &) i heard that Fiat M7.6.3 readable only by K-Line , and hardly to figure, how mpps read/write its eeprom by CAN bus.

[walopower]

Same "application exception error". Win10, have tested with other computers win7 and win10 and it work, but why not in this computer?
MPPS folder not need to be c:\, not need launch from shortcut, not need launch as admin, all these advices are bullshit, because it works without these my other computers.
Of course I have tested these on this computer without success. I have lot of applications in this computer and everything else works, also NET framework should work.
I hope somebody really know what these error mean. I know windows reinstall probably fix this, but I don't want use days to reinstalling all. If you have some other idea please tell, thanks.

[Bmwpower530]

Opened mine v18 today, should i place missing parts? D1 and U8? Cause now it's working very good on EDC15/16. Found D1 but dont know if it good to go. Add pics.

[donesko]

just bricked edc16c32 smart with v18, erased flash and then no response from ecu, fixed with bdm, in obd area only FF FF ..

[skzmaps]

Hello mates,

I'm looking for MPPS V18. There are only 2 variants for the moment ORIGINAL and EURO CLONE.
Clone you can buy for 500EU and ORI for 2500EU.
What can you say about them? Someone use it?
Maybe this tool is crap?
Thanks for comments


I have EU CLONE, v18 which it works perfect, never have had any problem until now


just beware on CHECKSUMS sometime it doesn't calculate checksums correctly!

[kriselektro]

Can someone check what is the value of the C22 element, I have the L1 designation, I have the pcb 2016 version

[Panathaole]

Hi guys....

Anyone had read a marelli 8f3 from suzuki with mpps v18???

[ProximaCentauri]

I've bought v18 from China, I was curious if I could full read/write a renault S3000 ECU with it. I got a bit surprised that they come with the same PCB as v21, but the flash reads 1.08.21 so I suppose it's a proper v18...? I just hope it doesn't lock up eventually.

912296

Anyway, I were unable to do a full read of S3000 flash. It almost does it - the 512kB file is almost complete, except for first 32kB from 0 to 0x7FFF which it reads as filled with FFs which is obviously not correct. Is it a chinese clone problem, or is it just MPPS limitation?
Now I'm curious if same problem applies to writing a flash file. I have a proper flash file someone else read with ktag or something similar, I also have a partially damaged (case and connector) ECU that wouldn't be a shame if it got bricked in the process, so when I have a little free time (it's not easy or quick to get to the ECU in Scenic II :rofl: ) I will try to do a full write with it.

It's also worth noting, that S3000 only works in the car, it won't read on the bench. I believe it's because of immo lock, as it stops on Security access and then throws a "Conditions not met" error. Not even virginized ECU works on bench.

I'm a little bit disappointed that it couldn't fully read it, but then again I could probably find this information with a bit more research. But at least it's a cheap tool, and I might find some use for it eventually. On the other hand, most of the cars it supports are rather aged and won't be driving on the roads that long... :rofl:

[ProximaCentauri]

Experimented with writing to the mentioned ECU, and unfortunately it's a no-go. MPPS v18 doesn't even try to do a full write to the S3000 and just writes the Data part - car wasn't driven that day and was cold so temperature's not a problem. The firmware ended up being a frankenstein's monster with most of it being from 1.4 and the data part from 1.6. It throws nonsensical errors and doesn't start anymore. There's still normal communication with it though, so I'm sure it can be easily recovered with a proper tool, but I'm not gonna bother.

Edit: I didn't immediately think of it, but I should be able to recover it by flashing the original 1.4 data section which I read before trying to flash the ECU with 1.6 firmware. That's for another day, I guess.