edc17 swap filles or immo off

[lush29]

hi all,
i have an audi a6 with damaged edc17cp14 part no 0281015018,03L906022FL hw h01, and i got an doner ecu edc17cp14 part no 0281016678,03L906019AG hw h03.i know they are not the same, but i can not find same part. I was trying to swap full read from ori to doner wich i did but still car not starting and safe on dash.
can someone do immo off or any other solution?
i attached both full reads doner and ori. thanks for your help

[lush29]

Any one?

Sent from my SM-G925F using Tapatalk

[Alpinesport]

you need to read full micro and eeprom

[lush29]

you need to read full micro and eeprom
I read both micro and eep and transfer both and still safe on dash and car not starting

Sent from my SM-G925F using Tapatalk

[lupu_sandu]

Read and post both ecu here, but no total read. Save files separately.

[lush29]

Read and post both ecu here, but no total read. Save files separately.

Thank you Lupu_Sandu , i attached both ecus with eep and micro separately

[lupu_sandu]

Put this eeprom in SH donor ecu. Int_fls of donor ecu must be original (not flsh from original ecu).

[lush29]

Put this eeprom in SH donor ecu. Int_fls of donor ecu must be original (not flsh from original ecu).

thank you very much Lupu_Sandu, but i made an mistake, i uploaded the filles from the ori ecu by mistake, both filles up there are from the ori ecu nothing from the doner (i read doner but actually inside doner was ori filles put by previous guy) ,so i got in touch with him and he give me the doner filles.
i am putting the proper ori filles and doner filles again this time the right once, please help me, and i am sorry for waisthing your time, but this car is been to someone else before me and thats way is this big mess around. thanks and sorry once again.

[rob h]

I have adapted the immo section and vin inside the donore dump. I used Tango dumpmaker!
Write this file, and the car wiil start. And i have made one extra immo off file asswel. Just to make sure.
Not having the correct partnumber could cause some problems.

398418

[lush29]

I have adapted the immo section and vin inside the donore dump. I used Tango dumpmaker!
Write this file, and the car wiil start. And i have made one extra immo off file asswel. Just to make sure.
Not having the correct partnumber could cause some problems.

398418
Thank you very much rob h. I also think not same part no will cause this because i also try smok and could not do it. I will try and report back. Thank you very much.

Sent from my SM-G925F using Tapatalk

[lush29]

hi all, just to inform after try both rob h filles car still have safe on dash and not starting, i scan car and have faults with both filles immo off and immo adapt,p1841 engine gear box not match, and P Flasing on the dash. so i need same part no ecu, when i get i will post filles. thanks a mill for your help guys.

[rob h]

Make sure that it has the same gearbox, or dsg type.
It need to see that the car is in neutral, or clutch pressed!


Try to put a plus direct on the starter,

[lush29]

Just want to say one more time thank you Lupu_Sandu and thank you rob h for your time. I will get same ecu part no. I will try to cross wire also .thanks

Sent from my SM-G925F using Tapatalk

[steveleo]

Test this one please.

[lush29]

still the same m8. thanks

[steveleo]

Get a ECU with same numbers and then i'll do a clone again. Np.