changing km with hex editor

[scatman75]

hi ive got this mk5 cluster partnumber 1k0 920 874 ,ive ff the immo off and followed all the directions to change the km,when i connect my a1 adapter it always errors out.
question 1 does it have to be connected to the car to rewrite the original dump to change the km
question 2 is there anyway to edit the km with a hex editor
if anyone can help ill really appreciate it..
thanks..
here is my cluster dumps

[Catdaddyfunk]

Does what have to be connect? what tool are you using?

[scatman75]

Does what have to be connect? what tool are you using?
does the cluster have to be connected back to the car or is bench testing still fine and im using carprog..

[Catdaddyfunk]

I got no idea what year or model is the car..is it for a VW? Audi?

[clusters]

No car make, no year, no chip number, no original mileage = no help.

[scatman75]

No car make, no year, no chip number, no original mileage = no help.
sorry thought with the cluster code it could of been worked out
its for a mk5 golf gti
2007 model
chip is 24c32
original mileage is 116000
im looking it changed to 303000
sorry for the lack of info my apologies..

[jomberykaso]

Hi mate, your file is bad, so bad.

Desolder eeprom 24c32 of dash , after that read it, verify it, save it and upload it here.

[jomberykaso]

Sorry mate....your file is ok, I opened another one...lol

[jomberykaso]

Here is your file

Original mileage was: 116.640 kms

New mileage is: 303.000 kms.

Good Luck!

[scatman75]

Hi mate, your file is bad, so bad.

Desolder eeprom 24c32 of dash , after that read it, verify it, save it and upload it here.
hi i took 3 dumps from the eeprom 24c32 all three verifyed ok..
heres a new dump done with carprog as ive no other way at presant to read it out of the board..

[jomberykaso]

Mate, your file is ok.

It was my mistake saying that your file was bad, because I was editing other file in my computer and I confused...that's all.

Use my file, it is what you need it

[scatman75]

hi mate works fantastic but is showing up as 302000 and not 303000..

[scatman75]

406170 here is a picture of what im talking about.

[jomberykaso]

Good Luck!

[scatman75]

thank you so much,quick question could you share on how you edit the file in hex editor to change the km,no worries if you cant..thank you again..

[yugo45]

This dash can not be done by eeprom only.
Either X-prog with connection to Mirconas or OBD.

[scatman75]

This dash can not be done by eeprom only.
Either X-prog with connection to Mirconas or OBD.
what tools are needed to marry this mk5 golf cluster up to another car,i see you mentioned x-prog,is there any other readers that can do it without removing chips..

[GameTheoryOptimal]

AVDI/FVDI will do this via obd.

[yugo45]

what tools are needed to marry this mk5 golf cluster up to another car,i see you mentioned x-prog,is there any other readers that can do it without removing chips..

AVDi, SMOK , VVDI2 , Car prog, there is to many tools that can do it over OBD.

[purepower]

Hi to all.

I found this post and I hope someone can help me. I'm completely lost. I'm doing an important mod on my car and the last step is to change the VIN on the cluster (only the VIN with the following WVWZZZ1KZAW415600).


Someone can do that on my attached dump file please? Is a Nec 24c64 from Scirocco III my2010



Thanks in advance (I can even pay for that if is working)

[yugo45]

Hi to all.

I found this post and I hope someone can help me. I'm completely lost. I'm doing an important mod on my car and the last step is to change the VIN on the cluster (only the VIN with the following WVWZZZ1KZAW415600).


Someone can do that on my attached dump file please? Is a Nec 24c64 from Scirocco III my2010



Thanks in advance (I can even pay for that if is working)


Not possible , OBD only.

[purepower]

Which tool can I use in OBD? (clone)
Originale too expensive just for a shoot.

Thanks

[yugo45]

Look at post 19 .
There is not cheap way to do this dash.