w230 SL 55 NEED ORI FLASH EZS

[mitext]

Hi dk! need ori flash ezs 230 545 07 08 h2. mcu r2 ,r1 4j74 y , thanks advance

[mitext]

Will not anyone help

[daxxer]

i have this EZS the same part number now on the table, wait...maybe i can help you... ;)

406561

[daxxer]

not help, VVDI Prog can read only eeprom, O5 can read only eeprom :(

[parapilot]

O5 should read flash, bottom right by vcc voltage should be a drop down box to select what to read.

[daxxer]

O5 should read flash, bottom right by vcc voltage should be a drop down box to select what to read.

O5 not good for read HC08....in circuit very bad, need to remove some parts and/or cut some wires....desolder is much work...i need to have the EZS still working back to the car.. :listen:

[mitext]

05 the best programer! EZS its same, must be removed chip

[mitext]

someone will help having read the files, flash drive is damaged

[daxxer]

05 the best programer! EZS its same, must be removed chip

sry, when i can't help you in this case, but its not my EZS for playing or training and i need to have this car running :)
this EZS type for R230 model is very hard to find as used :( and the new is little more expensive :(

[Jan1980]

Did you make the processors warm with hot air ? Often, this works. Then, you know processor is damaged... 4j74y are piece of shit...

ETL908 can read flash and eeprom 100% ! Desolder processors and read them with etl fast and easy. Buy new processors and write dumps to them. But, don?t go with 4j74y, use brand new 2j74y !

[duplikeytor]

Etl908 original or clone? I can't find link to original. Did it stop production after they made a newer device?

[lush29]

I did one this week using smok. All ok but i also read it as 2j....

Sent from my SM-G925F using Tapatalk

[mitext]

I have a brand new 2j74y but the flash is damaged on R1. Do not handle the heat, there is an error internal damage. Odometer shows -------

[mitext]

I may read it and sign ETL and oranje 5 no original files this problem. R1 is damaged

[duplikeytor]

I did one this week using smok. All ok but i also read it as 2j....

Sent from my SM-G925F using Tapatalk

is your smok serial number above 3800? If so, what connection diagram did you use?

[lush29]

is your smok serial number about 3800? If so, what connection diagram did you use?
Is 3800 higher. I can send you diagram in the morning.

Sent from my SM-G925F using Tapatalk

[duplikeytor]

Is 3800 higher. I can send you diagram in the morning.

Sent from my SM-G925F using Tapatalk
sd

I would appreciate it as everyone tell me SMOK cannot read 4J74Y secured in circuit.

[MarkPRP]

I have this switch on bench, will read flash tomorrow


Sent from my iPhone using Tapatalk

[lush29]

sd

I would appreciate it as everyone tell me SMOK cannot read 4J74Y secured in circuit.
I will pm in the morning the diagrams for it mate.

Sent from my SM-G925F using Tapatalk

[dominik.m]

IN RAR 2x MOT read ETL

[Ismael20]

use ak500, have a option for ?repair the flash?

[SK Auto]

Hi dominick
can i have the password please

[duplikeytor]

I did one this week using smok. All ok but i also read it as 2j....

Sent from my SM-G925F using Tapatalk

So

the mask was 4j74Y and you read it as 2J74Y?

I'm trying to read it as 4J74Y and it's unsecuring but then read error. In circuit SMOK

[duplikeytor]

I will pm in the morning the diagrams for it mate.

Sent from my SM-G925F using Tapatalk

AwaitingWiringDIagramPlease

[JFR-Tuning]

IN RAR 2x MOT read ETL

please pass

[bersch8688]

And R270 cant read Flash?

[ktome]

Hi Dominik

Can i have the password please
Thanx Tome

[devil008]

IN RAR 2x MOT read ETL

Hi can you please send the pass