PDA

View Full Version : 2005 VW GOLF Secondary air injection delete



BestElectrical
1st November, 2016, 06:25 PM
Hello, Can somebody help delete secondary air injection
2.0 VW golf 2005
PN: 06A 906 032 RF
0 261 208 561

Flash memory AM29F800BB
407424


The engine was replaced and now there is no holes in cylinder head for secondary air injection. Now getting codes and cannot fix it without replacing cyl head.

Thank you,

BE

Act Tuning
1st November, 2016, 06:36 PM
You need to post the fault code you have, that someone can help you,

BestElectrical
1st November, 2016, 07:25 PM
What about readiness? is there any way to turn it off and make it N/A?

Act Tuning
1st November, 2016, 07:30 PM
no, it just need to remove the dtc and thats it,

Act Tuning
1st November, 2016, 07:35 PM
If i remeber its should be P0410 fault, do you want i remove it for you and try, if you can get dtc

BestElectrical
1st November, 2016, 07:42 PM
Yes, please. thank you a lot

spychu14
1st November, 2016, 09:34 PM
P0410=Secondary Air Injection System
P0411=Secondary Air Injection System Incorrect Flow Detected
P0412=Secondary Air Injection System Switching Valve "A" Circuit
P0413=Secondary Air Injection System Switching Valve "A" Circuit Open
P0414=Secondary Air Injection System Switching Valve "A" Circuit Shorted
P0415=Secondary Air Injection System Switching Valve "B" Circuit
P0416=Secondary Air Injection System Switching Valve "B" Circuit Open
P0417=Secondary Air Injection System Switching Valve "B" Circuit Shorted
P0418=Secondary Air Injection System Control "A" Circuit
P0419=Secondary Air Injection System Control "B" Circuit
P0491=Secondary Air Injection System Insufficient Flow Bank 1
P0492=Secondary Air Injection System Insufficient Flow Bank 2
P2257=Secondary Air Injection System Control “A” Circuit Low
P2258=Secondary Air Injection System Control “A” Circuit High
P2259=Secondary Air Injection System Control “B” Circuit Low
P2260=Secondary Air Injection System Control “B” Circuit High

P2430=Secondary Air Injection System Air Flow/Pressure Sensor Circuit Bank 1
P2431=Secondary Air Injection System Air Flow/Pressure Sensor Circuit Range/Performance Bank 1
P2432=Secondary Air Injection System Air Flow/Pressure Sensor Circuit Low Bank 1
P2433=Secondary Air Injection System Air Flow/Pressure Sensor Circuit High Bank 1
P2434=Secondary Air Injection System Air Flow/Pressure Sensor Circuit Intermittent/Erratic Bank 1
P2435=Secondary Air Injection System Air Flow/Pressure Sensor Circuit Bank 2
P2436=Secondary Air Injection System Air Flow/Pressure Sensor Circuit Range/Performance Bank 2
P2437=Secondary Air Injection System Air Flow/Pressure Sensor Circuit Low Bank 2
P2438=Secondary Air Injection System Air Flow/Pressure Sensor Circuit High Bank 2
P2439=Secondary Air Injection System Air Flow/Pressure Sensor Circuit Intermittent/Erratic Bank 2
P2440=Secondary Air Injection System Switching Valve Stuck Open Bank 1
P2441=Secondary Air Injection System Switching Valve Stuck Closed Bank 1
P2442=Secondary Air Injection System Switching Valve Stuck Open Bank 2
P2443=Secondary Air Injection System Switching Valve Stuck Closed Bank 2
P2444=Secondary Air Injection System Pump Stuck On Bank 1
P2445=Secondary Air Injection System Pump Stuck Off Bank 1
P2446=Secondary Air Injection System Pump Stuck On Bank 2
P2447=Secondary Air Injection System Pump Stuck Off Bank 2

Apsik
2nd November, 2016, 01:25 PM
Your file is a bit different to what i'm used to (1.8T) but SAI should be OFF.

Readiness monitor is set to unsupported (VCDS should show PASSED).

However you may have cold start issues because I did not found SAI flow related maps.
Can't find ESCONF either to fix the circuit related DTC's for pump and relay, but will try to do it later.

Test the file and I'll add some improvements later
407539

BestElectrical
2nd November, 2016, 06:19 PM
Thank you for the help.
Here is what I get when I write this dump back into the module.
SAI is still on. I can hear it when I start the car and it is still failing the readiness.
Any other ides?

Apsik
3rd November, 2016, 07:49 PM
try this and report

V2
407840

kinketotua
4th November, 2016, 06:57 AM
here you can try these
unplug pumb
--> 407929

BestElectrical
4th November, 2016, 06:11 PM
here you can try these
unplug pumb
--> 407929

Thanx for the help,
After writing file back to module, SAI still not set/failed on readiness.

Do you have any other ideas?

Thank you

kinketotua
5th November, 2016, 08:06 AM
sorry friend..I dont have another solution to disable these system. good luck

Apsik
5th December, 2016, 12:05 PM
OK 3th attempt
MSLUB and CDSLS 00'ed
Keep the SAI relay pluged in and let me know.
413553