Can help me remove dtc p2015?

[pukymar]

Hello can help me please remove dtc p2015?
car passat 2007 engine (CBDC)2.0 edc 17CP20
read flash with FGtech V54
VW Hardware Number: 03L907309B

this is error
1 Fault Found

008213 - Intake Manifold Flap Position Sensor (Bank 1)
P2015 - 000 - Implausible Signal - MIL ON

[filetuning]

Hello can help me please remove dtc p2015?
car passat 2007 engine (CBDC)2.0 edc 17CP20
read flash with FGtech V54
VW Hardware Number: 03L907309B

this is error
1 Fault Found

008213 - Intake Manifold Flap Position Sensor (Bank 1)
P2015 - 000 - Implausible Signal - MIL ON


Thanks and report please

407624

[pukymar]

wrong file.Ecm canbus blocked

[pukymar]

It can help someone else?

[filetuning]

[Quote = pukymar; 2883738] Pu? aiutare qualcun altro [/ QUOTE]

?
the file is correct, the problem is your experience with open ecm works

[filetuning]

wrong file.Ecm canbus blocked ahahah ahaahaha



the file is correct, the problem is your experience with open ecm works

[igendek]

Try and report. Pass PM

[pukymar]

Man with your file, the engine started, but after sitting overnight I did not want to start. 01 314 engine control module - no signal / communication. After I took all canbus hand I see that there is no problem. the ECU diagnosis I could not do when he was attached to the car. I did diagnose with him on the table, went perfectly. After I wiped errors, surprise canbus see ECU, the engine started. After another state 10 min contactless same problem. So? A colleague from another forum gave me a file that wiped P2015x4_18447x4 and now everything is ok. Attach file to consult , and then maybe see what's the problem.Anyway thanks for your time

[pukymar]

Tnx man. SOLVED

[filetuning]

[Quote = pukymar; 2883834] Tnx uomo. RISOLTO [/ quote] the file that I have worked is the same as that made you the other user does not understand why you say that compare two files and see

[filetuning]

Tnx man. SOLVED
the file that I have worked is the same as that made you the other user does not understand why you say that compare two files and see

[cawadany]

Yes. I can confirm. Two files are the same!

[pukymar]

I'll tell you how it happened. I did not touch anything, and nothing happened to the ECU. When I wrote the first time the car started smoothly, but after a period of 15/20 minutes of stand ecu no longer communicating with the car. Fgtech communicate because I wrote the original tab, but the car still does not see ECU. I checked and CANbus wires were okay. How I managed to solve the problem. I did the ECU diagnosis on the table and I removed all the errors, then began to communicate with other modules. I tested the car for 2 hours and there were no problems. I put in new tab changed and I had the same problems.
When the car did not see ECU, instrument panel is no longer lit the spark plug, ESP error, servo direction was active

[pukymar]

I'll tell you how it happened. I did not touch anything, and nothing happened to the ECU. When I wrote the first time the car started smoothly, but after a period of 15/20 minutes of stand ecu no longer communicating with the car. Fgtech communicate because I wrote the original tab, but the car still does not see ECU. I checked and CANbus wires were okay. How I managed to solve the problem. I did the ECU diagnosis on the table and I removed all the errors, then began to communicate with other modules. I tested the car for 2 hours and there were no problems. I put in new tab changed and I had the same problems.
When the car did not see ECU, instrument panel is no longer lit the spark plug, ESP error, servo direction was active
Anyway thank Mr. Filetuning