View Full Version : Ford Ranger sid 208 - best tool to use
pulsar2000
18th November, 2016, 10:14 PM
Anyone know if Fgtech works on this ECU,
its a 2013 Car, Sid208,
read some reports saying FGTECH doesnt work on Fords, although will work sid 208 other Makes other than FORD,
dont suppose new MPPS v18 covers ?
Also needs a Decent power supply Correct ?
Anyone info please and Cheers
smirnoff_rules
18th November, 2016, 10:20 PM
l know its has tricore TC1797 same as edc17c10 and l know mmps reads that but if it has the patch to unprotected files l dont know
100% need 13.8 some even 15
https://i.gyazo.com/cd7976b7ba940ddedd41cb5f286e6e22.png
pulsar2000
18th November, 2016, 10:27 PM
Hoping someone has some good info, got one coming in soon, Got kess and dont think Kess covers on boot mode this ecu,
if need be have to get a K TAG again, to cover this ecu,
P,s Smirnoff, Nice touch on the Photo, Bit of chinese Copyright Protect,,,, LOL
smirnoff_rules
18th November, 2016, 10:46 PM
l have looked through all my stuff and only ktag shows it m8 in transdata , mpps/kess/fgtech checked, if you where around Birmingham you could borrow it
pulsar2000
18th November, 2016, 11:20 PM
l have looked through all my stuff and only ktag shows it m8 in transdata , mpps/kess/fgtech checked, if you where around Birmingham you could borrow it
Cheers for the offer and Input, Mate,
Unfortunately not close enough, Maybe i need to sort out a K tag again,,,, Long story had 1 but bust,
Aliexpress here we come,
Cheers mate
looly
21st November, 2016, 12:49 AM
I did one of these vehicles approx 2 months ago using ktag. Worked perfectly. The hardest part of the job was removing the ecu from vehicle. It's located drivers side footwell and has security bolts holding it in. A right pain to remove!
BrunoPT
21st November, 2016, 12:34 PM
i make a 5\6 cars with sid 208 and use x17 tool.
Reggards
voltechcar
21st November, 2016, 02:11 PM
all orginal tool read ford with sid208 k-tag, x17, galetto
pulsar2000
29th November, 2016, 02:27 PM
l have looked through all my stuff and only ktag shows it m8 in transdata , mpps/kess/fgtech checked, if you where around Birmingham you could borrow it
Hi mate i PM you, maybe you can help, if you can let me know either way, Cheers
smirnoff_rules
29th November, 2016, 02:54 PM
replied m8 .................
pulsar2000
30th November, 2016, 05:57 PM
replied m8 .................
Big Thanks to you mate, Shows that this great site, brings knowledge and friends who help one another :unionflag:
J_amb_o
30th November, 2016, 06:57 PM
You do so many cars, i don't get why you are still using clone tools!
pulsar2000
1st December, 2016, 08:12 AM
You do so many cars, i don't get why you are still using clone tools!
Because i cant afford master tool, and i tried slave tools and if dont get on with masters High prices and slow service i cant do allot,
very simple answer,
and clone does job just as good,
good enough ?
jakkeviet
1st December, 2016, 08:58 AM
all org tool support ford sid208 but which support PEUGEOT BOXER SID 208 ???
twincam
1st December, 2016, 09:29 AM
PSA sid208 is not possible to read for this moment .
Sent from my HTC One A9 using Tapatalk
soundnavigator
1st December, 2016, 09:53 AM
Original FGTech support Ford/Land Rover SID208/SID209 ECU unlock/read/write. PSA SID208 not supported at now.
BR
pulsar2000
1st December, 2016, 12:36 PM
Conflict opinion even Original tool,
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.