Peugeot - Citroen FAP filter deactivation [Sitemap] - Page 2

pug407

22nd February, 2011, 07:50 AM

OK, I now have a BDM100 interface to read my SID803A but it didn't come with a connector to suit. I can solder wires to the pads on the ECU board. But does anyone know which pins on the BDM go to which pads on the ECU? I have a pic of the ECU here Bild:SID 803A.jpg - OBD-Wiki (http://wiki.obdtuning.com/?title=Bild:SID_803A.jpg)
Does pin 1 on the ribbon just go to pad 1 on the ECU etc...?

Thanks.

8k65m

22nd February, 2011, 10:29 AM

You it is necessary to study this: http://www.evc.de/ftp/winols/BDM100en.pdf

pug407

22nd February, 2011, 10:36 AM

Yes, that shows where the pads on the ECU are but I do not have the small board with the pins. I can solder wires to the pads but don't know which wire to which pad.

sohail786

22nd February, 2011, 08:14 PM

thanks btr
i will report back asap, but do i need to remove the sensors physically?

thank you

btr

22nd February, 2011, 09:20 PM

No,don't disconnect sensors,only reflash ecu.

sohail786

22nd February, 2011, 09:52 PM

No,don't disconnect sensors,only reflash ecu.

my car is still in limp mode after reflashing with galletto 1260! :mad: the revs dont go past 3000....is there something im doing wrong :confused:

btr

22nd February, 2011, 10:03 PM

maybe car has another problem,this file is correct.

sohail786

22nd February, 2011, 10:23 PM

i will check fault codes with pp2000 maybe it does have another problem.
thanks for your help btr

bloodth

23rd February, 2011, 01:13 PM

Maybe someone tells how to correct cheksum in EDC16C34
winols with ols285 ver2.61 can not

rossoelab

24th February, 2011, 01:25 AM

hello
problem with 307 1.6 HDi FAP
after disabling the FAP sw esp fault indicator lights
everything works fine with the original file
help me please

rossoelab

24th February, 2011, 01:37 AM

hello
problem with 307 1.6 HDi FAP
after disabling the FAP sw esp fault indicator lights
everything works fine with the original file
help me please

1037374174 EDC16c34
original file here and not fap
help me please

decodercar

24th February, 2011, 10:00 AM

need dpf off Peugeot 406 2.0HDi

0281011080
1037364200

Thanks.

woodywoodpecker

24th February, 2011, 07:46 PM

[QUOTE=decodercar;988573]need dpf off Peugeot 406 2.0HDi

0281011080
1037364200

Thanks.[/QUOTE

Dpf removed my friend.

woodywoodpecker

24th February, 2011, 07:56 PM

1037374174 EDC16c34
original file here and not fap
help me please

Try this m8

rossoelab

24th February, 2011, 09:03 PM

Try this m8

thanks but
This file is the same as mine and not good
ESP lights with error U1208 (communication with the engine ECU, invalid data)

victor2k

1st March, 2011, 10:16 AM

nice... that theory was posted by me last year on eurovan2 forum when I bought my C5 1.6HDI FAP and had to solve the FAP problems...
my problems was simple just: FAP washing + Eolys refill and additive computer reset and all was ok.

To be sure that FAP will complete each regeneration properly I developed a device that signal regeneration phase on HDI engines so no more problems:
Sensor Regeneration FAP & Turbo temperature (http://www.phones-direct.ro/public/fapsensor/index-uk.html)

In the meantime I study a different approach of FAP removal:
if anybody with Lexia have access to PSA engines with no FAP: DV6, DW10, DW12 and can make a print of BSI & ECU configuration settings will be great to complete my study.

thx
Hello,
Please describe the reset procedure for the additive computer with unknown reference in PP2000
Thank you.

erniez

2nd March, 2011, 03:09 AM

thanks but
This file is the same as mine and not good
ESP lights with error U1208 (communication with the engine ECU, invalid data)

Any luck my friend?
Im having same troubles with same car.

rossoelab

2nd March, 2011, 10:00 PM

Any luck my friend?
Im having same troubles with same car.

problem solved 100%
replaced with another file with the same number but different sw
ESP works fine now
solution here

nPersp

3rd March, 2011, 12:40 PM

Hello,

I'm also having problem after flashing my C5 1.6 HDI. After flashing, i get Engine Management system faiulrem, ESP / ASR failure, and the "Risk of particle filter blocking" message is still there.

Any suggestions would be greatly appreciated!

nPersp

3rd March, 2011, 01:48 PM

Here are my files in case anybody could check if there's something wrong with them.

nPersp

3rd March, 2011, 02:31 PM

Now I'm stuck in limp mode with the Engine Management / ESR / ASR fault, even after flashing back the original ECU file.

Before flashing, I only occasionaly went to limp mode, and never got the ESP fault. I understand that flashing a modified ECU file could cause problems, but why is the problem still there when flashing back the original file?

I didn't find my car in EODB2 software list, so I flashed with EDC16+ as the main choice, but without selecting a specific car. Could this be the problem?

erniez

3rd March, 2011, 05:27 PM

problem solved 100%
replaced with another file with the same number but different sw
ESP works fine now
solution here

Damn. My flash readout has only 1MB. I gues we have different ecus.

erniez

3rd March, 2011, 05:30 PM

Now I'm stuck in limp mode with the Engine Management / ESR / ASR fault, even after flashing back the original ECU file.
(...).?
Did you tried to diagnose the car after flashing back? Dlette DTCs and so on?

nPersp

3rd March, 2011, 05:41 PM

No, I don't have any tools for this. I just have the Galletto 1260.

To be honest, I'm just a newbie who wanted to get rid of some very annoying DPF problems which have already cost me over ?1000. But I should probably have left this to the experts... I'm starting to panic, need my car for a 500km drive on sunday, and at the moment it just won't leave limp mode.

nPersp

3rd March, 2011, 05:54 PM

Maybe it helps if I explain in detail what i did:

I hooked up the Galletto and started the software. From the Select Maker menu i chose Citroen. Then for the Select Driver i chose EDC16+. I didn't find my car in the list (only Peugeots there) but I knew my ECU was an EDC16+ so I proceeded without choosing a car. Maybe this could have caused the problem?

Anyway, I switched on the ignition, read the ECU file and saved the original. Then i made a copy of it, and modified it in EcuSafe to remove DPF. Loaded the modified file back into the Galletto software, switched on the ignition and wrote the file back. Followed the instructions after flashing (10 sec ignition off then on etc).

When I started the car, everything is OK for the first second. Then the "service" light come on, and I get the message "Engine management system fault". THen the ESP warning lights up, and i get the ESP / ASR fault message. Finally, I get the "Risk of particle filter clogging" message. The car is stuck in limp mode.

Since the modified file didn't work, I tried writing back the saved original file. This gave the same result. I ahev enclosed the files in an earlier post.

I'm wondering if there could be a problem with checksums or something, especially since I couldn't choose my car model from the list in the driver selection window. Should I try with one of the Peugeots in the list, or di you think this will ruin everything even more?

citronel

3rd March, 2011, 06:29 PM

I think you have to go to Lexia diagnose and check ECU configuration and injector programming.

nPersp

3rd March, 2011, 06:51 PM

Thanks, maybe I just need to turn it over to the dealer to have the reprogram the ECU. Guess it's pretty hard to find someone else with a Lexia here in Norway...

nPersp

3rd March, 2011, 07:36 PM

Rossoelab, can i ask what you did different when you got it working? I think my problem is quite similar to yours.

soundnavigator

3rd March, 2011, 10:15 PM

No, after programming, you had to wait 3 minutes. If you do not do this and run the engine, you lose to the injectors code. Then need to coding again with PP2000.

Best regards.

nPersp

3rd March, 2011, 10:49 PM

OK, I didn't wait for 3 minutes, so maybe this is what I did wrong then. I waited just the 10 seconds with ignition off, then 10 seconds with ignition on, then started the car.

So if I flash again and wait 3 minutes will it be OK, or do I need to use a PP2000 for the injector codes anyway now that the car is in limp mode?

Nicowico

3rd March, 2011, 11:29 PM

You started the wrong way. Before you updated your Ecu, you had first to remove the Ecu faults with Lexia. After you have removed the Ecu faults you can update your Ecu with the NO Fap Ecu software and after that you have to remove the fap. Good luck.

rossoelab

3rd March, 2011, 11:51 PM

Rossoelab, can i ask what you did different when you got it working? I think my problem is quite similar to yours.

first checks the encoding injectors
Peugeot Citroen and often have this problem ...
if the injectors are ok
go to peugeot (Official lexia) and check that they have not deleted the data in the vehicle engine ECU (downloading)

plamen2

4th March, 2011, 12:37 PM

need dpf off Citroen c5
0 281 010 774
edc15c2
96 445 062 80

Thanks.

nPersp

4th March, 2011, 06:13 PM

Went to a Peugeot dealer today (no Citroen dealer nearby). They cleared the fault codes, but the car was still in limp mode. After one test run, two of the fault messages came back: ESP / ASR fault and Risk of particle filter clogging. I haven't seen the Engine Manegement system fault after this.

They said I needed to take the car to a Citroen dealer to get them to load a clean original ECU program. Will try this on Monday. Meanwhile I'm stuck in limp mode.

rossoelab

4th March, 2011, 10:03 PM

need dpf off Citroen c5
0 281 010 774
edc15c2
96 445 062 80

Thanks.

file fap off please

btr

5th March, 2011, 05:04 AM

enjoy...:smokin:

npepo

9th March, 2011, 09:24 AM

Hi guys

have you got experience with 2,7HDI fap removal.

the ecu is siemens SID201

i have ori ecusafe ,but this sw analize this ecu as sid803 and can not make regulary fap off.

do you have solution for this car?

Regards

soundnavigator

9th March, 2011, 09:58 AM

If you have ori Ecusafe send file to Fulvo to check it.

Best regards.

npepo

9th March, 2011, 11:56 AM

thanks, but with him is really bad the communication .

he is answering just randomly to mails. really bad support.

i am really disappointed with ecusafe.

so i am looking for other solution i will even pay for it.

thanks

grinovsky

9th March, 2011, 08:03 PM

npepo

9th March, 2011, 09:03 PM

Maskart

10th March, 2011, 12:18 PM

Hi!

I need help removing fap from this car:

Peugeot 407 2.0HDI

It's a Siemens 5WS40167G-T SID 803

Here is the file from the car:

npepo

10th March, 2011, 12:30 PM

hi

in this ecu the fap data is stored in MPC!!!

send content from Mpc

regards

Maskart

10th March, 2011, 03:48 PM

Sorry, I didn't know that. Here is the content from the MPC:

grinovsky

10th March, 2011, 04:40 PM

the file is from SID201

as you wrote, the ecusafe writes sid 803 instead of sid201, and i just updated my ecusafe so it has the latest database.

i also tried the dump modified with ecusafe (as sid803)
but the ecu writhes error message ..differential pressure sensor fault or fap filter missing......

so iam trying to find solution for this car

regars

ah,so ecusafe work fine with your dump
the DTC that you have is normal because you have removing fap physiquely
so; to resolve this probleme aded a resistor 10kohm to differential pressure sensor and erease the dtc
you will see that the dtc never will apear

npepo

10th March, 2011, 04:46 PM

do you mean i have to pull up the signal line to the +5v supply with 10kohm resistor?

thank you

npepo

10th March, 2011, 04:55 PM

here is it

your fap off file for 407 2,0hdi

grinovsky

10th March, 2011, 05:16 PM

no
add resistor betwen signal wire(conector) and sensor

Maskart

11th March, 2011, 10:40 AM

here is it

your fap off file for 407 2,0hdi

Thanks but I think the zip file is corrupted my friend. Can you please reupload? :(

npepo

11th March, 2011, 10:50 AM

file again in rar

npepo

25th March, 2011, 03:40 PM

hi grinovsky

the 10k resisitor not working.
do you have any other idea?

thanks

macmanCZ

26th March, 2011, 05:43 PM

Please help me for my Peugeotu 607 2.2HDI with fap.
I need disable the fap, it is my dump. I have Bosch EDC15 ECU.

thanks macman

btr

26th March, 2011, 06:39 PM

Please help me for my Peugeotu 607 2.2HDI with fap.
I need disable the fap, it is my dump. I have Bosch EDC15 ECU.

thanks macman
try this....

grinovsky

26th March, 2011, 08:56 PM

hi grinovsky

the 10k resisitor not working.
do you have any other idea?

thanks
i should work !!!
the ecu will not detect that the fap is removed mecanicly
so no limp mode

macmanCZ

27th March, 2011, 05:36 PM

Sorry for my bad English.. :-)

I Flashed nofap map from btr to my car and my car still need make regeneration FAP filter.. Fapoff map is binary same with my DIY map with ECUSAFE...

Is any another tool to make nofap from my map???

ECUSAFE doesnt work with my car...

macman

tignes

4th April, 2011, 06:19 PM

Hi!

I need help removing fap from this car:

Peugeot 307 1.6 HDI 110 CV

It's a Bosh EDC16C34

Here is the file from the car:

P2XA

4th April, 2011, 06:25 PM

Hi!

I need help removing fap from this car:

Peugeot 307 1.6 HDI 110 CV

It's a Bosh EDC16C34

Here is the file from the car:

try and report:

koyot

9th April, 2011, 10:51 PM

Please, can some one remove FAP from this file. It's from P307 2.0HDI 2004. I already tried with ECUsafe but doesn't work. Still have limp mode.

cosmind

10th April, 2011, 09:02 AM

try and post result.
mod with ecusafe v2

koyot

10th April, 2011, 06:17 PM

not ok
Still have limp mode
+ esp lamp

Bettyswollock

15th April, 2011, 09:17 PM

not ok
Still have limp mode
+ esp lamp

Try with DPF sensor attached and temp sensor unattached.

Krotov_FSB

17th April, 2011, 01:18 AM

Fiat Ulysse II 2,2JTD 4HW
Can you help with fully remove DPF from it?
I have EcuSafe...

Is anybody have another solutions?

jajo0

21st April, 2011, 09:14 PM

Hi,
can you help me to disable FAP in Peugeot 607 2,2 HDI with Bosch EDC15C2? (the car is from year 2002).
Attached my original dump.
Thanks in advance!
jajo0

tonnopazzo

3rd May, 2011, 11:06 AM

basta comprare (ecusafe) ? il problema si risolve

tuningschool

3rd May, 2011, 01:13 PM

basta comprare (ecusafe) ? il problema si risolve

ecusafe not working on many system
On only 2 system seems it working (but at 90% too)

RCS

3rd May, 2011, 02:11 PM

I have couple of cars in my family that require DPF removal...
What tools do you recommend for adjusting ECU, reading and writing it?
Galleto1260, BDM... what else is on the market?

Thanks...

TFT

3rd May, 2011, 10:01 PM

Hello boys.
I have a doubt.

If you spend the cartography for the ecusafe, the fap remains deactivated and does not regenerate any more?

Or does it continue regenerating?

The egr is annulled also or does not make it the ecusafe?

kastaniusss

9th May, 2011, 11:50 PM

hello, how I can read file from ecu on my 05 407 2.0 hdi, i tryed with galetto and i cant read, only can write, but with 1,6hdi 407 no problem, galetto worked perfect
thank you

moky

10th May, 2011, 04:06 PM

Someone have tested ecusafe v2 on bmw edc16 ? (530D 218hp 1mb)

Thx!

.

Igorka

25th May, 2011, 02:01 PM

Hi
Need help to disable FAP at my peugeot 607 2,2HDI 2002
EDC15
original dump attached

cosmind

26th May, 2011, 08:47 AM

post result

yas200979

27th May, 2011, 08:23 AM

Hi frend. Please help me. Citroen C8 2009 2.2 Biturbo. Ecusafe not work. I need remove FAP.
All damp:

btr

27th May, 2011, 02:42 PM

Hi frend. Please help me. Citroen C8 2009 2.2 Biturbo. Ecusafe not work. I need remove FAP.
All damp:
Try this,and don't forget report!pass in pm!

titobal

27th May, 2011, 07:06 PM

I Need to disable FAP for 307 SW HDI 110 - 2003.

EDC15C2.

Thanks !

yas200979

29th May, 2011, 09:30 AM

Try this,and don't forget report!pass in pm!

ECUSAFE 2.0 NOT WORK

I tested this file before!

jajo0

1st June, 2011, 09:56 PM

Hi,
can you help me to disable FAP in Peugeot 607 2,2 HDI with Bosch EDC15C2? (the car is from year 2002).
Attached my original dump.
Thanks in advance!
jajo0

Hi again! Can somebody help me to disable FAP in this car?
Thanks!

Foblas

2nd June, 2011, 10:49 PM

Hi again! Can somebody help me to disable FAP in this car?
Thanks!

Here you are.

Smac_a

3rd June, 2011, 08:29 AM

I Need to disable FAP for 307 SW HDI 110 - 2003.

EDC15C2.

Thanks !

Here you go!
65857
Should be ok, check checksum to be sure (done with ecusafe).
Please report.

Regards,
Smac_a

yas200979

6th June, 2011, 01:59 PM

Try this,and don't forget report!pass in pm!
You file not work!

elchip

6th June, 2011, 02:26 PM

ECUSAFE 2.0 NOT WORK

I tested this file before!

ECUsafe work 100% but only PSA EDC15 , problem is in other thing....
Remove FAP is not only COPY - PASTE ...

So peoples who only wait to other do something and they
only use that may do not work that job ...

Better find other way to make money or choice other hobby.

Regard's

yas200979

7th June, 2011, 11:40 PM

ECUsafe work 100% problem is in other thing....
Remove FAP is not only COPY - PASTE ...

So peoples who only wait to other do something and they
only use that may do not work that job ...

Better find other way to make money or choice other hobby.

Regard's

Thanks :roflmao:

micromax

10th June, 2011, 10:00 AM

hello, i need help, ES2 not work propetly. after 100km i have smoke.

peugeot 407

rtvservis

20th June, 2011, 09:46 PM

SID803 MC555
I READ WITH BDM PROG CAN I WRITE AGEN WIDOUT CHECKSUM SOFTWARE.

beppe_72

20th July, 2011, 08:01 PM

hello everybody I need your help.
I removed fap from fiat Ulisse 2.2
could someone check if the file is ok? thank you
Beppe

btr

21st July, 2011, 05:17 PM

hello everybody I need your help.
I removed fap from fiat Ulisse 2.2
could someone check if the file is ok? thank you
Beppe
try this,and report

engine83

24th July, 2011, 10:47 PM

btr

27th July, 2011, 03:46 AM

Hello. someone has removed the DPF to a citroen ds3 1.6 92hp?

I bought the car, but I have always problems with the dpf. you can delete? :beheaded: many thanks for your patience

1037506849
1037510526
Not very simple to remove from 1.6 hdi PSA group dear friend,only manual changes from dump solve this solutions,ecusafe not work!

pelot

27th July, 2011, 04:32 PM

Little help with fap needed. I have 407 2.0hdi with siemens SID803 onboard. Ecu safe don't work correct, in 300km goes into limpmode.
Anybody have another solution for this car? Not ECU safe... Here is bdm MPC and Eeprom. Thanks!

btr

27th July, 2011, 04:56 PM

engine83

28th July, 2011, 03:28 AM

Not very simple to remove from 1.6 hdi PSA group dear friend,only manual changes from dump solve this solutions,ecusafe not work!

thanks for the answer, there is another solution to ecusafe? unfortunately I am unable to modify it by hand. hello thanks

atd

28th July, 2011, 02:43 PM

In Renault edc16C3 ecu is similar problem. Ecusafe doesn't remove properly. But how to solve this problem manualy?
I read about ecu adaptation.
- btr any suggestions?

skin74

29th July, 2011, 12:18 AM

please help ! my 206 1.6 110cv fap have problems with the fap filter need the file off this car to eliminate this issue thanks and the best reguards im young here and i canot dawnload the files please rui.rmatos@gmail.com i have lexia 3 diagbox

btr

29th July, 2011, 06:10 AM

But how to solve this problem manualy?
I read about ecu adaptation.
- btr any suggestions?
Manualy you must change org dump at the known addresses the map's dpf,or use swiftec software:ciao:

sazam

29th July, 2011, 06:26 PM

Please help me for my Peugeot 406 2.2HDI with fap.
I need disable the fap, it is my dump. I have Bosch EDC15 ECU.

sazam

29th July, 2011, 06:28 PM

the file...

btr

29th July, 2011, 07:26 PM

the file...
try this...

moky

10th August, 2011, 12:09 PM

hi

i have a question,does ecusafe 2 work fine on 406 2.2hdi 136hp and 2.0hdi 110 ? (edc15) ?

Thx !

Evaldazj

23rd August, 2011, 09:43 AM

please need to remove FAP peugeot 407 1.6hdi. edc16c3/9.17 file atached

Evaldazj

23rd August, 2011, 09:44 AM

and what shoud do more?Disabled fap in BSI?What more??

straki007

29th August, 2011, 09:37 PM

Hi frend. Please help me. Citroen C8 2009 2.2 Biturbo. Ecusafe not work. I need remove FAP.
All damp:

Here is with ES3 online original.

eduardo74

30th August, 2011, 09:13 AM

Anyone try to reflash engine 9HZ with full eprom reading with 9HX file, for example there are same ECU but software with FAP, and some older version without FAP?

atd

30th August, 2011, 09:41 AM

In BSI also. . .

Straki007 do you have Ecusafe 3.0 with online acces?
If I good understand write plz how does it work with new ecus(france group, new opels and edc17xxx)?

btr

1st September, 2011, 05:34 AM

In BSI also. . .

Straki007 do you have Ecusafe 3.0 with online acces?
If I good understand write plz how does it work with new ecus(france group, new opels and edc17xxx)?
I do not think that is very different from ecusafe3 and 2.0 especially in the PSA group (mask all foult's codes in ECU ...regenerations....):ciao:

btr

1st September, 2011, 05:40 AM

Anyone try to reflash engine 9HZ with full eprom reading with 9HX file, for example there are same ECU but software with FAP, and some older version without FAP?
I think would not workable, potentially different wire ends ...

straki007

7th September, 2011, 06:53 PM

Yes mam ECU safe third Is there a difference in that from it we've done online. Dela there any difference about it is still bad. For EDC16 PSA's limiter switch as crack turbo version. It is horror. EDC17 it still can not.

macxlulu

7th September, 2011, 06:59 PM

Psa 1.6 Hdi orginal no fap version :)
I had not just a flash in the car longer to read the full file BDM :)

eucsafe not you suggest to see the structure of fap, car filter is not meant to never, I know of a source of the difference between the version of fap and without a single bit of difference, as is the case in EDC16 1.9 and 2.0 tdi vag,

you can also load full of BDM, and also add immo should just work FAP OFF

you can certainly in vag ppd in the 2.0 140, came out serially fap-free version if I remember correctly Tip 03Gxxxxxx18CE numbers

eduardo74

7th September, 2011, 09:49 PM

maxlulu: I understand that is ok in VAG group, but if I find similar or very "close" software, should be possible to do good fap off on 1.6hdi changing from fap flash to non fap flash?

macxlulu

7th September, 2011, 09:59 PM

yes, but it can not be the same flash file only complete BDM, or find one bit of difference versions with and without fap fap

you can also ECU can be changed from the version without fap

he once swapped so that the ECU ford focus 1.6 tdci :D

few years ago when there was no ecusafe just as we were doing with the PSA group in August EDC15 load the file without fap to the version of fap

eduardo74

7th September, 2011, 11:06 PM

maxlulu thanks for info, I will research that solution. I always using BDM, its risk free!

simo2011

4th October, 2011, 05:29 PM

Hello
Please ,remove the torque limiter from the file I am attaching to this post and send it back to me if you do not mind

Thanks in advance

arosoft

18th October, 2011, 09:49 PM

Please help me removed FAP in my peugeot 407 2.0 HDI
ECU is SIEMENS SID803

TrzyEr

19th October, 2011, 07:21 AM

hi! anyone can help me with Citroen C8 2.2 hdi EDC15C2 2002r??
84750

hhp

20th October, 2011, 10:16 AM

C5 1.6 HDi can someone please check the file with FAP OFF?, Thank you

eduardo74

20th October, 2011, 11:11 AM

C5 1.6 HDi can someone please check the file with FAP OFF?, Thank you
post your original file also. Ecusafe cannot do job for 1.6hdi

Azzx

20th October, 2011, 11:36 AM

hi! anyone can help me with Citroen C8 2.2 hdi EDC15C2 2002r??
84750

Attachment, checksum corrected.

hhp

20th October, 2011, 04:39 PM

Thank you, I am sending ori file. Why can not I do with Ecusafe EDC 16?

btr

20th October, 2011, 06:40 PM

Thank you, I am sending ori file. Why can not I do with Ecusafe EDC 16?
ecusafe not work with psa edc16 regenerations after 50 km....

yas200979

20th October, 2011, 07:50 PM

:top:Who has a solution?

macxlulu

20th October, 2011, 08:19 PM

me :) PSA FORD or Mazda 1.6

eduardo74

20th October, 2011, 10:36 PM

Your file will regenerate again. Sorry.

Thank you, I am sending ori file. Why can not I do with Ecusafe EDC 16?

hhp

23rd October, 2011, 08:18 AM

Can anyone help with removal? Thank you in advance

Boonaldo08

10th November, 2011, 05:25 PM

Hi did you manage to find someone to remove the fap from the ecu for you ?? i too am interested in this. Try looking for a member called woodywoodpecker - he was more than helpful with me - good luck

bazare

10th November, 2011, 05:28 PM

good solution is not for free.

hhp

24th November, 2011, 07:50 AM

Good day, gentlemen, can you please check file C5 1.6 HDi FAP off? Thank you in advance

btr

7th December, 2011, 08:01 PM

Good day, gentlemen, can you please check file C5 1.6 HDi FAP off? Thank you in advance
this job only for sale car...
:smokin:

titobal

10th December, 2011, 03:52 PM

Hi all,

First I would like to thanks all the people in this
"Magic" forum for the help and advices provided
during this 'FAP/DPF removal' adventure ;-)

I have done a successfull ECU EDC15C2 flashing
with physical FAP/DPF removal last september/october.

All is okay now but when I diag the car I still have
a permanent fault (catalytic converter related)
and from time to time an "Anti pollution error"
message which goes away few restart/ignitions later ...
the limp mode gets on when I have the antipollution message but then goes away when the "Antipollution error"
goes away too...

I have no power loss or degraded mode all is running
properly apart from that.

Is there a way to get rid of this error (each time I diag):

"Permanent fault , catalytic converter upstream temperature signal , Short- circuit to positive or circuit open ."

If I clear the error code it comes back again immediately
after (without limp or antipollution error)

Best Regards & Thanks for taking the time to read.

:egg:

Azzx

10th December, 2011, 04:10 PM

Turn FAP on in BSI and the DTC will dissapear.

titobal

10th December, 2011, 04:20 PM

Thanks for your answer.

Really ?

I've been told to turn it off in the bsi
as well as the additive system, which I did.

Best Regards

titobal

14th December, 2011, 07:34 PM

Doesn't work...

FAP present but the problem is still there.

btr

16th December, 2011, 04:10 AM

Thanks for your answer.

Really ?

I've been told to turn it off in the bsi
as well as the additive system, which I did.

Best Regards
If you turn off in bsi fap,in the engine ecu arise foult's as adattive or Can network problems...stupid idea

titobal

16th December, 2011, 08:51 AM

So you suggest leave in BSI :

FAP on
Additive ECU on

as I did this and still have the error plus the pump
in the additive tank is not working anymore on my car.

Thanks

Foblas

16th December, 2011, 09:12 AM

i can try to remove manualy from 1.6hdi. But need feedback after removing. i have no 1.6 for check now. Safety and free. PM if you need.

meteor80

16th December, 2011, 10:31 AM

Hello.
I need remove fap in 307 2.0 HDI ecu BOSCH 0281011248.
Is ecusafe2 work OK with this?
what sensors I need to disconnect and what need to leave.

Foblas

16th December, 2011, 12:38 PM

meteor80, use ecusafe, then reprog. Thats all.
You may also disable fap in bsi, but its not necessary.

alex1986

16th December, 2011, 02:12 PM

Hi ,i got problem on active my Lexia 3 . it show Error :
The software cann't be activated as the RRDI code is unkonw to the system !! how do i slove it ?

Regards

Maradonna

16th December, 2011, 11:43 PM

So you suggest leave in BSI :

FAP on
Additive ECU on

as I did this and still have the error plus the pump
in the additive tank is not working anymore on my car.

Thanks

Remove the temp sensor on the Fap.

mouaoued

2nd January, 2012, 06:45 PM

help pilz fap off edc15c2 0 281 010 370 406 hdi 2.2l 136

woodywoodpecker

3rd January, 2012, 02:47 AM

help pilz fap off edc15c2 0 281 010 370 406 hdi 2.2l 136

Here you go mate

thomash3

4th January, 2012, 03:13 PM

Hello.
307 2.0 HDI ecu BOSCH can someone please check the file with FAP OFF?, Thank you

96393

btr

5th January, 2012, 03:48 AM

Hello.
307 2.0 HDI ecu BOSCH can someone please check the file with FAP OFF?, Thank you

96393
here for you

sazam

11th January, 2012, 11:44 PM

try this...
Hi, sorry for take a long time for report. The file is good. I have a problem, better, big big problem whith this. Engine broken because one piston and rings are damaged and oil ascend and burn. Engine game over, and the owner blamed me...Solution: change the engine, pdf off with same file and all happy. Always test the car before doing anything

B.R
sazam

vampirodauva

18th January, 2012, 12:59 AM

hi
i have peugeot 206 1.6 hdi ecu bosch 0 281 011 560 edc16c34 and need put off this fap , i have tryed with ecusafe but dont work . someone can help me ?
thanks in advance
regards

zilekv

18th January, 2012, 08:25 AM

Hello.
I need remove fap in 307 2.0 HDI . Is ecusafe2 work OK with this?

btr

18th January, 2012, 02:30 PM

Hello.
I need remove fap in 307 2.0 HDI . Is ecusafe2 work OK with this?
how much kw engine?100kw or 79kw?

Boonaldo08

24th January, 2012, 02:48 PM

Hi, could someone remove the dpf / fap files with ECU safe for the attached ecu file.

Thanks

Boon

Azzx

24th January, 2012, 02:58 PM

Hi, could someone remove the dpf / fap files with ECU safe for the attached ecu file.

Thanks

Boon

Ecusafe do not work on 1.6 HDI (EDC16C34).

gogoli

26th January, 2012, 11:14 AM

please can you help me I need off FAB
peugeot 307
2.0 hdi
2003

THANKS

barbos

26th January, 2012, 01:32 PM

307 EDC15FAP off

gogoli

26th January, 2012, 06:42 PM

THANKS MY FRIENDS
IT,S OK...

gijoe

26th January, 2012, 07:07 PM

When i kill the FAP of 806 2.2 hdi the temperature sensor show 752 C it is normal use ecusafe

Azzx

26th January, 2012, 07:20 PM

When i kill the FAP of 806 2.2 hdi the temperature sensor show 752 C it is normal use ecusafe

It is normal.

tanoy

30th January, 2012, 08:41 AM

Hello
I'm with this issue quite familiar, but I advise anyone what type of equipment, these files into the ECU to apply, tell me please!

Boonaldo08

31st January, 2012, 12:01 PM

why doesnt ecusafe work with edc16c34 ?

yas200979

31st January, 2012, 02:12 PM

why doesnt ecusafe work with edc16c34 ?
Ecusafe clear all mask error. Not stop regeneration. Car after it is non-diagnostic. Ecusafe kills car :ridinghorse:

xomuxot

1st February, 2012, 02:45 AM

Hi all, can you please turn off fap on this file for me, thanks in advance.

307 sw hdi 110 1.6 edc16c34

macxlulu

1st February, 2012, 08:23 AM

he he- go to local tuner

btr

1st February, 2012, 07:59 PM

or use ecusafe:thefinger:

thomash3

9th February, 2012, 05:38 PM

please can you help me I need off FAB
peugeot 807
Thanks
2.2 hdi102469

Smac_a

9th February, 2012, 06:42 PM

Hi.

This was done using ecusafe 2.0 with ecd15 peugeot...
Check chksum.

Regards,
Smac_a

102481

please can you help me I need off FAB
peugeot 807
Thanks
2.2 hdi102469

jacekpopierducha

12th February, 2012, 10:06 PM

witam chce wy***322;.FAP w peugocie 307 hdi 1,6 110KM 2007 r.BOSCH DHC 16.jaki przyrz***261;dy mam kupi***263;?

jacekpopierducha

12th February, 2012, 10:08 PM

witam chce wywalic322;.FAP w peugocie 307 hdi 1,6 110KM 2007 r.BOSCH DHC 16.jaki przyrzady261;dy mam kupic;?

jacekpopierducha

12th February, 2012, 10:12 PM

Not very simple to remove from 1.6 hdi PSA group dear friend,only manual changes from dump solve this solutions,ecusafe not work!

jakie urzadzenie trzeba kupic?

electrix

13th February, 2012, 07:25 AM

The only hardware is nothing for that job. And if You don't know which hardware is needed, probably You don't know how to manual disable FAP in dump. Don't waste Your time and let pro tuners to do it.

fargulkim

18th February, 2012, 01:03 AM

Hi all, can you please turn off fap on this file for me, thanks in advance.

307 sw hdi 110 1.6 edc16c34

here for you

kastaniusss

29th February, 2012, 03:48 AM

Hello, can somebody help to me turn off fap from my peugeot 307 1.6 hdi 110hp 2005 please, thank you

yas200979

29th February, 2012, 06:53 AM

Hello, can somebody help to me turn off fap from my peugeot 307 1.6 hdi 110hp 2005 please, thank you

Pass - send me PM.

jacekpopierducha

3rd March, 2012, 05:57 PM

jak BDM 100 wy***322;.FAP z EDC16C34-prosze o instrukcje?

jacekpopierducha

3rd March, 2012, 06:06 PM

jak wyl.fap BDM100
z EDC16C34 PEUGEOT

djorgensen

5th March, 2012, 06:26 PM

Could someone help with removing the DPF from this Citroen C4 vehicle:

EDC16

ECUSafe doesnt work with the ECU

Thanks

yas200979

5th March, 2012, 06:55 PM

Could someone help with removing the DPF from this Citroen C4 vehicle:

EDC16

ECUSafe doesnt work with the ECU

Thanks

Pass in PM: Manusign:

petersatan

5th March, 2012, 11:41 PM

Please dpf off

Thanks

yas200979

6th March, 2012, 06:17 AM

Please dpf off

Thanks

use ecusafe.

Vint75

7th March, 2012, 09:16 PM

here file from peugeot 407 1.6 hdi 2006 ECU bosch-0281012984.
can you remove FAP please?

FiltersMurderer

9th March, 2012, 08:58 PM

Raport pliz

carlion79

12th March, 2012, 10:28 PM

please remove the fap on ecu maps.
with ecusafe not possible...
peugeot 206 1.6 hdi 110cv EDC16C34 bosch
thanks:giveup:

FiltersMurderer

15th March, 2012, 02:22 PM

keep the file 100% working, the password in a PM

lmsvvavr

16th March, 2012, 09:43 PM

Hi everyone!

I have tried to remove FAP in the ecu of a peugeot 307 2.0HDI 110PS, fitted with the ECU Bosh EDC15 C2.
ECU safe says removal successfuly, the message for the anti pulution keeps coming up...
Can anyone have a look to see what is wrong?
Any help will be mutch apreciated...
BTW, I have tried all options in ECU safe...

cosmind

17th March, 2012, 10:55 AM

disable fap from bsi

lmsvvavr

17th March, 2012, 11:46 AM

disable fap from bsi

Hi
I think I've done that, I've disabled everything related to the fap system... but I do still get the message... or there is some hidden ones?
Can you or anyone confirm that the file above that says nofap is ok?
Also, should I disconnect the fap pressure sensors, or that should not make any difference?

nicuriuc

20th March, 2012, 05:05 PM

Hello all.
I have a Peugeot 407 and want to cancel FAP if possible.
the fall to do it myself but I ecusafe and until I can.
ECU edc16c34 9653958980 .1039 s1564s
thanks

Smac_a

21st March, 2012, 07:50 AM

@lmsvvavr:
Did you remove fap (the exhaust part)? Keep sensors on. If you disconnect them, you'll get dtc...

Regards,
Smac_a

lmsvvavr

21st March, 2012, 09:09 AM

@lmsvvavr:
Did you remove fap (the exhaust part)? Keep sensors on. If you disconnect them, you'll get dtc...

Regards,
Smac_a

Hi
No, the filter stills in place... the anti pollution message appears on the screen, but in the ecu there is no more dtc for that...
I am know awaiting for the accelerator pedal, when the anti pollution pop up in the ecu appears errors for pedal, despite the fact that I have measured the pedal and all values look ok...
When the message comes the accelerator start to respond very roughly, and the engine as well... oh, the engine light and esp comes at the same time... I have read somewhere, that in some cars the fap sensors need to be disconnected, otherwise the ecu doesn't know what to do with does values, as the tables for the system no longer exist...
Any ideas?

Smac_a

21st March, 2012, 02:55 PM

Hi.

Keep sensors and remove dpf... and that is it.
As for pedal... remove dpf and if dtc is still there look for errors.

Regards

zorro

22nd March, 2012, 05:15 PM

hi Peugeot 307 FAP off please from this file thanks

ivomarchev

22nd March, 2012, 07:23 PM

Hello.
I need remove fap in 607 2.2 HDI ecu BOSCH 0281010765.
SW 1037353571

yas200979

22nd March, 2012, 08:44 PM

Arhiv bad.

lmsvvavr

24th March, 2012, 01:16 AM

Hi.

Keep sensors and remove dpf... and that is it.
As for pedal... remove dpf and if dtc is still there look for errors.

Regards

Hi guys...
Update: right, further investigation revealed that something was short, after the dfp removed from the ecu using ecu safe, the anti pollution message keeps showing on the screen, and engine light on, but when diagnosed there is nothing related to the anti pollution, only electrical faults with accelerator.pedal, fuel pressure sensor, turbo boost sensor, all the above with the description, short to ground, or open circuit, and then another one saying power supply to several sensors, and again short to ground or open circuit...
So, this make me believe tba the last fault is common and the cause of all the other ones, and probably the anti pollution one as well... I'am correct?
Later, and with the engine running, I was touching on the cables and plugs around the area where the 4 solenoids are, just behind the radiator, and the engine cut out! Wow! I thought, my problem is somewhere around here, I started the engine again touch the area and engine of again... well, after about an hour investigating I couldn't find nothing, but I have unplugged and plugged back everything in that area.... went for a spin and it took much longer for the engine light and message to came on, and even after that the car seems to run just fine, before, the car used to become irresponsive, erratic acceleration, and engine misfire...
Will diagnose again, curious to see what is there now, but in the mean time, any one have an idea about this kind of problem?

ivomarchev

24th March, 2012, 09:21 PM

here a the new one

yas200979

25th March, 2012, 09:09 AM

here a the new one

Worked. Free.

nicuriuc

25th March, 2012, 10:47 AM

Hello all.
I have a Peugeot 407 and want to cancel FAP if possible.
thanks

zorro

26th March, 2012, 08:01 PM

Bosch ECU EDC16C34 .
Peugeot 307 1.6 hdi please remove fap from file thanks

zorro

26th March, 2012, 08:04 PM

Bosch ECU EDC16C34
Peugeot 307 1.6 hdi please remove fap from this file thanks

psico

28th March, 2012, 11:02 PM

HI
Anyone know how to disable peugeot 607 ecu siemens sid201 fap?
Thank you.
I have a reading with bdm

Min2xx

30th March, 2012, 09:05 PM

Bosch ECU EDC16C34
Peugeot 307 1.6 hdi please remove fap from this file thanks
307 DPF off for you by ES, CS ok

yas200979

31st March, 2012, 11:21 AM

307 DPF off for you by ES, CS ok
I repeat, does not work ekusafe in EDC16c34.

sarkann

31st March, 2012, 01:50 PM

Please could someone romeve dpf from my renault edc16c34?
please no ecusafe files, it doesn?t function.

nicuriuc

1st April, 2012, 11:19 AM

people. There will be tortured to find here something free. I was disappointed more. Here everything is paid. I do support forum to get some information, but all I see is the private message and prices.
I knew no longer pay to fund those who make money on it.
Forum - discussion is not biznes investigation.
better to open another post prices.
greetings

yas200979

1st April, 2012, 04:51 PM

Show me - who works for free? Or want to do it all the time. You're customers are not doing it for free?

nicuriuc

1st April, 2012, 05:27 PM

We are here to learn

nicuriuc

1st April, 2012, 05:27 PM

before you know someone explained. I do not mean to do it for granted, po you explain how you do. are many with the ecu and all that and hear only, 'en passoword pm.
Yas200979 Sorry if I offended you, but I happened. I fail to pay for a harm done, and I could not claim it. PayPal is not responsible for bad quality.
greetings

Novik_UA

1st April, 2012, 07:29 PM

Think, is no car owners here.
So, if you make a job, you make it for money. So you can pay and make a job perfect. If you look look for free, try to find resolve by yourself, and and then make it for free someone else.

nicuriuc

1st April, 2012, 08:53 PM

lmsvvavr

1st April, 2012, 08:59 PM

I did not find anywhere how. I have three weeks looking for information to these ECUs. In this forum we speak only of money. If you will acer money you can rename it to a commercial site. Pay for finding information, not to this web feed merchants.
a greeting

M8, you are so wrong... First your attitude is not exactly an example...
I found great help on this forum, and every time I have helped someone, was for free...
I do understand, (an you should as well), that some people here worked hard to find for solutions, repairs etc, and I don't blaim them if they ask for money when someone wants the "plate served ready"... however, I do not believe that members here would refuse to help you on what they can...
:giveup:

slonenok1980

12th May, 2012, 04:31 PM

help please
c4 grand pikassa 2006year sid 803a
5ws40615a-t
ecu safe not worc
winols
.....
help help

mexanico1971

25th May, 2012, 04:11 PM

TIP, for trickle signal additive minimum level ?!
what can be do ?!
br

spawns3

27th May, 2012, 01:47 AM

TIP, for trickle signal additive minimum level ?!
what can be do ?!
br

Turn off the DPF manually and all dtc codes for DPF .

AGS

27th May, 2012, 04:05 AM

TIP, for trickle signal additive minimum level ?!
what can be do ?!
br
If Pegeot or citronen you need to disable fap in bsi,or set reset counters additive,tested solution

electro68

31st May, 2012, 02:52 PM

hello i Hello guys, I have to delete the fap of peugeot307, you can help me?
thank you very much

deluss

5th June, 2012, 09:57 PM

@electro68 This is EDC15C2 so Ecusafe do it correct. Here you are ...

djbiugi

5th June, 2012, 10:47 PM

Hi boys...i have a problem too with EDC16C34 Peugeot 308 1.6hdi 110hp after dpf off

after some chilometers,car put out white smoke because start regeneration :-(

can help me please with a correct dpf off? thanks a lot ;)

Smac_a

7th June, 2012, 04:48 PM

@electro68 This is EDC15C2 so Ecusafe do it correct. Here you are ...

Hi I heard somewherte on DK that ecusafe is not ok for EDC15C2... I also did one with it and until now it's ok!
Is this 100%?

Regards,
Smac_a

tarekdj

12th June, 2012, 11:21 PM

Smac_a

13th June, 2012, 07:50 AM

hi all,
I have a Peugeot 406 2.2hdi EDC15 year 02/2001.
I have a probleme with DPF '' Anomalie Additif Gasoil '' since 5 day without any problem of the engine, speed is good.
With Multidiag he tell me that is impossible to communicate with the ADDGO, and low additif.
If i use Ecudafe tu remove DFP from the calculator and bsi ,and remove it phisicly, can you tell me if the DFP indication in the OBD desappear.
Thanks

Hi,
just an update from me; for edc15c2 ecusafe is ok for hdi 2.0,
but it doesn't work on 2.2hdi (not 100%).

NEW UPDATE (7.8.2012): Ecusafe 2.0 works also on 2.2 hdi 100%...

Regards,
Smac_a

tarekdj

13th June, 2012, 09:54 AM

Hi,
There is many people ho do it with ecusafe with no problem, someone tell that ecusafe work with bosch and not with siemens, is it correct
Regards

thomash3

20th June, 2012, 05:00 PM

hello i Hello guys, I have to delete the fap off C8, you can help me?
thank you

thomash3

21st June, 2012, 09:58 PM

hello i Hello

milzal

7th August, 2012, 07:10 AM

On SID803A canot make only reflash ecu frim ecusafe file. Here is info about any "Combinated solution". https://vcpowerteam.com/products/swiftec-dpf-removal-module/ Must make any next change in car.

Smac_a

7th August, 2012, 07:26 AM

Hi all!

Just to let you know ES 2.0 works ok on edc 15c2 (also on 2.2 HDI). Did a couple and we also did a couple of tests with tarekdj...

Regards,
Smac_a

smayer

8th August, 2012, 01:15 AM

Anyone to make dpf off in 2009 C5 ECU delphi DCM 3.4 ?

milzal

8th August, 2012, 09:58 PM

bosch work fine, delphi donot know, but sid803A not work right without next change.

AGS

8th August, 2012, 10:32 PM

bosch work fine, delphi donot know, but sid803A not work right without next change.
with manual dpf off siemens and bosch work fine,delphy dcm3.4 best way good dpf emulator!dangerous ecu,not way full restore hitachi processor

MAGHRIBI81

9th August, 2012, 02:41 AM

MAGHRIBI81

9th August, 2012, 02:47 AM

hello i Hello guys, I have to delete the fap off C8, you can help me?
thank you

THE FILE MY FRIEND

AGS

9th August, 2012, 05:00 AM

IS THE FILE :
I look it, "good" solution,mask all faults and turbo overboost....lol

milzal

10th August, 2012, 08:06 AM

manual dpf off on sid803A , like donot change sw in ecu, only reconect presure sensors and remove dpf ?

ciekawy

28th August, 2012, 11:33 PM

Could someone help with removing the DPF from this Citroen C4

EDC16C34
0 281 012 980
96 634 761 80

- pressure valve is faulty
or you can disable it

ECU Safe and Volta doesn't work with the ECU
Thanks

proel

29th August, 2012, 07:15 AM

LOL. it's not possible.

- pressure valve is faulty
or you can disable it

ECU Safe and Volta doesn't work with the ECU
Thanks

yas200

29th August, 2012, 08:19 PM

marek128

30th August, 2012, 02:05 PM

Im trying to remove FAP from C5.
Im using ES.
Im saw some posts that ES dont do this ECU good

Can U help me with this:
ECU: EDC16C34
96 632 457 80
9653958980 1844 0356

tigerryes

5th September, 2012, 02:07 PM

I am hopfully just about to change the ecu file on my citroen c5 2.2 hdi 2002
I have had the file changed but was wondering if someone could check both original file and new file to make sure its correct before i do it.
also assuming its ok and i put it on the car will i be ok then? no faults? Will the additive still be used and eventually run out causing an error?
I would love to be able to speak to someone on the phone who can change files on here so i can make sure i do everything in the right order. I am using kwp2000+ to change file.
Also how would i attach file to be checked?
thanks in advance
I am in the Uk, scotland

Smac_a

6th September, 2012, 12:33 PM

You have pm.
btw do you have flash programmer in case you fail to write trough OBD?

I am hopfully just about to change the ecu file on my citroen c5 2.2 hdi 2002
I have had the file changed but was wondering if someone could check both original file and new file to make sure its correct before i do it.
also assuming its ok and i put it on the car will i be ok then? no faults? Will the additive still be used and eventually run out causing an error?
I would love to be able to speak to someone on the phone who can change files on here so i can make sure i do everything in the right order. I am using kwp2000+ to change file.
Also how would i attach file to be checked?
thanks in advance
I am in the Uk, scotland

F-1

15th October, 2012, 10:56 AM

Hello all,
I have a Peugeot 607 2007 and I want to remove FAP, if possible, ecusafe can't do it.
ECU edc16cp39 0281012478 9662489680 1039s20197
thanks

mexanico1971

15th October, 2012, 06:19 PM

Hi all!

Just to let you know ES 2.0 works ok on edc 15c2 (also on 2.2 HDI). Did a couple and we also did a couple of tests with tarekdj...

Regards,
Smac_a

I do not think that is totally for shore !
i have now a C5 2.2 edc15 c2 that start to give a lot of DTC"s !
and the DPF off was made at 5 or 6 month"s ago !
now it always boost overload !

Smac_a

16th October, 2012, 06:53 AM

Why do you think boost has something to do with dpf off? Turbo maps should stay the same (mine did). Check your turbo solenoid valve, variable turbo and pipes in general. fap -wtf?

I do not think that is totally for shore !
i have now a C5 2.2 edc15 c2 that start to give a lot of DTC"s !
and the DPF off was made at 5 or 6 month"s ago !
now it always boost overload !