PDA

View Full Version : Crafter 2011 edc17cp54 ecu briked after dpf remove



catala20032004
14th December, 2016, 08:41 PM
Hello friends.
Ive tried to remove dpf on a 2011 vw crafter 20tdi ckuc engine ecu edc17cp54. Since i dont have the tool to read this i took the ecu to a local tuner that read it and write it back dpf off with cmd master original. After writing dpfoff ecu was briked car dont start. starter doesnt turn anymore. On diagnosis no dtcs on ecu. No more sw# nor hw# on ecu. Ecu is blank. Reading is in attach. can someone please tell me how can i recover this ecu?

smirnoff_rules
14th December, 2016, 08:50 PM
did you open it or him ?

catala20032004
14th December, 2016, 09:01 PM
He did. And read it in boot mode. We tried to write it back with cmd via boot and via obd no success. We tried to flash it back with odis no success. We took it to dealer tryed to flash it online . No succsess. Someo e with original avdi told us that something in eeprom area is missing or corrupted. Tried to recofigure flash ad eeprom with avdi wrote it back avdi sais all ok but still car dont start. Ecu shows nothing on diagnosis

smirnoff_rules
14th December, 2016, 09:35 PM
l would email this guy http://www.digital-kaos.co.uk/forums/member.php/327091-kire106ka he knows alot about cloning these

catala20032004
14th December, 2016, 09:57 PM
Just emailed him. Hope he joins in to the matter ☺. i dont know what to do anymore with this car

mihaiservice
14th December, 2016, 10:09 PM
Hi
Can Bus still are alive on ecu ?

kire106ka
15th December, 2016, 01:02 AM
Irom files are ok exept eprom i didn't have time to check tonight too tired i will see tomorow byt there is possibility that you have bricked ecu on first look eprom seems ok.
If you fit on car you have diagnostic comunication with tester tell us more info so we can help

icezero2010
15th December, 2016, 07:53 AM
Hello friends.
Ive tried to remove dpf on a 2011 vw crafter 20tdi ckuc engine ecu edc17cp54. Since i dont have the tool to read this i took the ecu to a local tuner that read it and write it back dpf off with cmd master original. After writing dpfoff ecu was briked car dont start. starter doesnt turn anymore. On diagnosis no dtcs on ecu. No more sw# nor hw# on ecu. Ecu is blank. Reading is in attach. can someone please tell me how can i recover this ecu?

all files looks ok connect ecu on bench and do diagnostic with vcds check if the dtc work and mesuring blocks . if not check how many ampere the ecu at 12V use and tell this us . is the ampere slower 0,40 than the ecu not boot check the ecu for damage if you nothing found clean the ecu with air and isopropanol

if this all not work you need new

catala20032004
15th December, 2016, 09:05 AM
Hello yes i have communication with tester. ECU is found. No DTC. No mesuring bloks. No HW# and no SW# showed on first page of ecu on vcds. The only communications i have on car is with ECU. How many flashes the ecu support. In ODIS shows something that only 10 updates can be made. Than no more. Is there a maximim writes of flash? This one allready has 7 till now

mihaiservice
15th December, 2016, 10:03 AM
Hi
With ODIS you can not resflash ecu even Online when ID are mising from ecu ! the only solution are VasPC but you have to edit ediabas.ini file to load calibration file from external drive or directory ! here you have calibration file with the same sw no.

catala20032004
15th December, 2016, 10:20 AM
Thank you Mihai. I have this file also. we've flashed it allready. Flash its ok. Eeprom cannot write. This friend iof mine that has genuine AVDI is telling me that he flashed this calibration you also gave me but eeprom cannot write

kire106ka
15th December, 2016, 12:25 PM
immo id VWXDZ0K1032042
component sequrity 409798D9F21200
mac 1 D131
mac 2 4E3D
pin 03483

Eprom looks ok all data is correct immo is learned
If you are near macedonia i would help you too see ecu here on table
test these write and make cks from tool
Regards Kire