View Full Version : Full BDM VW Passat 2007 PPD 1.5G
CrBooster
14th January, 2017, 06:10 PM
Hello! Does anyone have full BDM read for this ECU? You have attached my partial read with MPPS V16. Car is a VW Passat 2.0 TDI BKP 140 HP 2007. Thanks in advance!
03G906018FG
SN100L3000000
421377
smirnoff_rules
14th January, 2017, 06:22 PM
dont have a bdm for this have an ori read , think my mpps
only bdm one l have is
Hardware Version: 5WP45600AC
Software Version: 6576286349
Upgrade Software: 03G906018CD 9970
but thats not good for you
CrBooster
14th January, 2017, 06:53 PM
Thank you anyway. Maybe someone else have the right one.
CrBooster
15th January, 2017, 11:06 AM
Hi! Can anyone confirm that one of this is the full bdm read? In PPDMaps says that they aren't
421471
smirnoff_rules
15th January, 2017, 11:16 AM
thats shows all ff in start off bin
https://i.gyazo.com/92107437862cd2695a8f0d15be7bfa64.png
my bdm read is 00 in start
https://i.gyazo.com/7155620a0719d30136aa1c624902f9de.png
normally obd reads fill blacks with ff
CrBooster
15th January, 2017, 12:46 PM
Ok :( Thanks! Still looking for that BDM file then.. Or have anyone instructions on how to read it? I have Kess, Ktag and BDM Frame.
smirnoff_rules
15th January, 2017, 01:09 PM
are you looking for bdm in case obd write fails ?
CrBooster
15th January, 2017, 01:22 PM
Yes. I also have MPPS V16. I used it to read and write a PPD 1.1 without problems but on PPD1.5 i read that someones have some difficulties.
smirnoff_rules
15th January, 2017, 01:28 PM
havnt read to much about kess havin problems if you have a good one , normally if it reads ok it will write ok , use a good power supply should me ok . l have one here but l dont think theres an obd pinout of this ecu, if there was l would try on bench for you , siemens are better to write to ,
kess is very good on older cars and so is mpps
https://i.gyazo.com/46d39a6e3773fa09d340c788f4f22a18.png
CrBooster
15th January, 2017, 01:55 PM
Another reason that I'm in doubt on using KESS V2 is because on this particular car, it says it have EDC16U ECU instead of PPD 1.X
421499
smirnoff_rules
15th January, 2017, 02:06 PM
just read id and file if thats ok it will write ok ( more than likely)
CrBooster
15th January, 2017, 02:09 PM
And should i select correct car but with that wrong ECU that it gives or should i select a different car but with corect ECU PPD 1.X ?
smirnoff_rules
15th January, 2017, 02:15 PM
even you picked wrong one kess tells you the right one , pick your ecu and read id
CrBooster
15th January, 2017, 02:26 PM
Ok! Thank you very much! I will give it a try this week and i will tell you how it went.
kevin33140
15th January, 2017, 02:32 PM
smirnoff (http://www.digital-kaos.co.uk/forums/member.php/46-smirnoff_rules) is right my friend !!!:stung:
tango
15th January, 2017, 03:48 PM
i have the same car
passat 140hp bkp engine with ppd.1.5 ecu and kess reads it fine
i havent wrote to it but read the ecu no problem
Mihalych
15th January, 2017, 03:49 PM
try this file
CrBooster
15th January, 2017, 05:47 PM
Is the same as mine partial read.. And also is something strange with your file because it have 256kb. @tango have you read your file by selecting vw passat 2.0 tdi BKP EDC16U ?
tango
16th January, 2017, 01:22 PM
yes im sure i did but will try to read again and let you know
CrBooster
17th January, 2017, 04:02 PM
Hello guys! I have not yet tried to write or read the PPD 1.5 with KESS, but today i just bought an ECU 03G 906 018 FG PPD 1.5G and I want to read it by BDM and to see if it have the right SW. Until now i only read and write ECU vis OBD port and this is new to me. I have KTAG and a BDM frame with adapters (include Siemens adapter). Have any of you read this ECU by BDM? Thanks!
CrBooster
18th January, 2017, 05:53 PM
I tried today to read it with KTAG but i get this error. Have anyone any idea how can i solve this problem? Thanks!
422326
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.