Zed Bull other operations, other with programs

[f2f2]

Several operations have what we can not do now the programs or not quite good Solution is Now

I'm trying to understand and I'm trying to write Small additional programs.
The ZedBull developer is very strong protected access.

I test WinXP and Read info; Read chip (4D) ; write 4D works.
The PG4 combobox upload from directory system. (directory name)



425043


425044


425045


425046


425048

[f2f2]

....Moment

[f2f2]

425766

Add function
PC command Zed Bull reboot. Reset,New welcome message and info display.....

Add project system (add project to select pg4 directory )

Program start load the last key data

HUNtpRW[4D].Exe

[paganini]

Can you share this program?

[f2f2]

Yes
a bit more I'm working on it after you can try

I tested only winXP.
But you have Zed Bull Clone ?

[chli1976]

I have Mini Zed Bull clone but without RJ45 connecter.
Does your programm work with my zed bull ?

[paganini]

Yes I have Zed Bull Clone


Yes
a bit more I'm working on it after you can try

I tested only winXP.
But you have Zed Bull Clone ?

[f2f2]

RJ45 connecter. ..... This no problem
right point can be incorporated within MAX232 chip 4 pieces of capacitor

connection point 1.GND 2. +5V 3.RxD 4. RxD to Max232 and to RS232 1 RxD 2 TxD 3 GND 4 optional +12V If TPX cloner hardware tape hack.




and connector
build on his side

You may be used
JMA TPX cloner or Clone version

--------------------------------------------------------------------
Or hack2 no need max232
Zed bull to RS232 connected GND RDX TXD logic0 0Volt Logic1 +5V
The work TPX cloner
2 pin build to free RS232 pin

If necessary drawings I send pictures

This 2 version
1. serial comport mode -9V +9V communication
2. direct mode without voltage driver chip

I help you in ?

[f2f2]

431056

HUNtpRW[4D] exe works ZED BULL Clone
reboot; get info;4D read;4D write
All data save to project

Install step
zip file unzip to disk
connection Zed Bull device with the USB cable
Star EXE list all COMport and Click Start automatic search Zed Bull hardware and
created file ZEDBULL.COMPORT

If exist ZEDBULL.COMPORT file and hardware opened okay then no automatic comport serach panel


Exe work Read 4D chip; ZB. display RESP data to manual mode edit program RESP textboxs
if no exist pg4 data after TPX cloner pg4 read manula mode (COPY 4D;TPX Cloner; .....) pg4 to manual mode edit program PG4 textbox
pg4 name edit and Click ADD TO DATABASE

All project reload enabled okay

In case of problems emergency exit -> Right Mouse but

If read no correct and cycle read then click Right Mouse; next step Click Reboot; Read chip

[chli1976]

If necessary drawings I send pictures



Please, send pictures, Thanks

[f2f2]

The Mini Zed Bull and TPX cloner 100% works

426356

426357


426360
426361

426363

The TPX cloner +12V from Zed Bull (RS232)

1. Work
Zed Bull 3 or 4 pin connected
2. Work
TPX cloner optional 12V tape to RS232 and the MA3223 chip pin13 output channel (TxD)
and pin15 input channel (Rxd )

[f2f2]

426408
426409


426410


426411


426412

[dtip]

Zedbull cant write any TPX chip and i think it is hadware flaw....4d clone box will calculate but how do you write TPX chip with zedbull ?

[f2f2]

So far I could not be TPX1 and 2 write.
I write 4C and 4D to EH2 and I take expensive machines Copy TPX.

But now I test Zed Bull direct control (PC LPT port to PCF7991AT)
Now read TEMIC 11 12 Megamos 13 LPT port.
If the technique so that I can expand it is a special wiring you can then write :
TPX1 /2; TPM1-ID(TP08 clone chip) ; TP04
Or direkt LPT port or microcontroller build to Zed Bull.

[f2f2]

426455


Wiring diagram for Mini Zed Bull and TPX Cloner use
TTL assign level communication.

[f2f2]

I will have a good technical description of TPX chips.
In which it is described, to the signal sequence to write. THX

[f2f2]

If you are interested : Zed Bull software or Effi sw in Chip writing mode what data send to Zed Bull device
eeprom bin - > TP chip write
image generated ->TP chip write

I can watch and if necessary I will show you. If bin file you send me eeprom file.

[f2f2]

for example :
Effi pincode & key maker 96. modull

(Chevrolet,Daewoo E4 immobox Kalos, Lacetti, Leganza, Matiz, Nubira, Aveo, Tacuma, Spark)

The Zed Bull Chip programming work:
still unwritten TP08 or TPM1
Megamos Crypto menu World 4 to 9 all data AAAA
This data stored 93LC56 eeprom 0xC0 to 0xCB

Other write work no (PIN, UM2)


New chip ID write to eeprom:
The Key ID write eeprom the key block 0x00 to
It recommended to keep unchanged 0x00 to 0x05 fix old data

0x06 to modifiable
Read TP08/TPM1 chip
eeprom_new_keyID_1.byte = ID_2.byte
eeprom_new_keyID_2.byte = ID_1.byte
eeprom_new_keyID_3.byte = ID_4.byte
eeprom_new_keyID_4.byte = ID_3.byte
eeprom_new_keyID_5.byte = 0x00
eeprom_new_keyID_6.byte = 0x00

first key no more = 6 byte 0xFF

no key number store
---------------------------------------------------------------------------------
And you can watch other modules what kind of perform programming work on a chip.



Philips ID33
Zed-Bull modull 16
ORI_TPchip PCF7930/31
Clone_TPchip:TP05/PCF7930/31/35
93c46/93c56 8pin, 128/256 Bytes
Renault: Kangoo(-2001)
Clio(-2001)
Trafic(-2001)
Master(-2001)
Opel: Movano(-2001)
Dacia: Supernova
-------------------------------------------
exe file \Zed-Bull_MODULL(16)_File{IVker_ClioII(2001),93C46_Clio 2001_16bit.bin}.Exe
commandline IVker_ClioII(2001),93C46_Clio2001_16bit.bin
bin file IVker_ClioII(2001)\93C46_Clio2001_16bit.bin
----------------------------------------
Key_pos.: 1
Eeprom bytes: C6-0C-34-00-50-26
Chip data:
30-C0-0F-00-F8-01-FC-00-
00-00-C0-F1-03-F8-71-00-

-----------------------------------------------------------------------------------------
Megamos ID13
Zed-Bull modull 4
93c46 8pin, 128 Bytes
Fiat: Barchetta
Brava, Bravo(-1998)
Cinquecento
Ducato(-2001)
Marengo
Panda(-2002)
Punto(-1999)
Seicento(-1999)
Tempra
Lancia: Dedra, Delta
Citroen: Jumper(-2001) , Relay(-2001)
Peugeot: Boxer(-2001)
-------------------------------------------
exe file \Zed-Bull_MODULL(4)_File{Lancia_Delta(1995),93C46_Lanci aDelta1995_16bit.bin}.Exe
commandline Lancia_Delta(1995),93C46_LanciaDelta1995_16bit.bin
bin file Lancia_Delta(1995)\93C46_LanciaDelta1995_16bit.bin
----------------------------------------
Key_pos.: 1
Eeprom bytes: 06-7C-99-AD
Chip data: FF 81 34 80 DD 94 BA 42
----------------------------------------
Key_pos.: 2
Eeprom bytes: 06-3C-5A-F9
Chip data: FF 81 34 80 0D 55 D2 13
----------------------------------------
Key_pos.: 3
Eeprom bytes: 06-BC-DC-58
Chip data: FF 81 34 80 6D D6 71 79
----------------------------------------
Key_pos.: 4
Eeprom bytes: 06-BC-34-30
Chip data: FF 81 34 80 6D 3A C0 38

[f2f2]

Chip Reading from Zed Bull without USB cable

--------------------------------------------------------------------------------
Zed Bull device PCF7991AT chip 3 pin connected: PC PRINTER port
--------------------------------------------------------------------------------
------------------------- Initialising and READ chip ID ------------------------
--------------------------------------------------------------------------------
bitlep 334 10240 [ID11]
EEprom code: BE FA 00 00 01 4D 27 A7
Zed code: 5F 00 00 80 B2 E4 E5 7D
flag5F: 3
flagS: 32
--------------------------------------------------------------------------------
GET_SAMPLING_TIME: 00000000
GET_PAGE_00: 00000010
GET_PAGE_01: 00000000
GET_PAGE_10: 00000000
GET_PAGE_11: 00000000
GET_PHASE: 00010100

[chaz1702]

I recently purchased big zed bull and it did not connect to the decoder box and i am not very good with changing circuit parts, does anybody know of a seller who sells a good quality board that allows a decoder box to be plugged straight in?

[f2f2]

Do not be surprised I also have great Zed Bull and he joined not the decoder.

Probably many of these are
Give a good quality of pictures
I have drawn on what you can do

Perhaps the difference in production equipment not designed for through to the decoder

Will you solder?

[mikajna]

I have big size zeb bull also, but sometime it connect to cloner, thats lottory when it will connect to cloner to decode transponder
I dont know how to fix this problem... :(

[f2f2]

If you are you can tie the PC comport to TPX Cloner
I send short program and you know test that TPX Cloner 100% okay

If you are you can tie the PC comport to ZED Bull Cloner port
I send short program you check Zed communication

GND TxD RxD only 3 pin

If necessary I will send the programs

[f2f2]

TPX Cloner full communication test software
Connection PC serial comport to TPX Cloner box


In the evening I write and it will be This test program

428779

[f2f2]

TPX Cloner check with PC .... Download exe Link: http://www.digital-kaos.co.uk/forums/showthread.php/576485-TPX-Cloner-full-communication-test-software-Needs-PC-and-TPX-Cloner

[mikajna]

I'm using that TPX cloner with Quickly Cloner 4C/4D/46 (copy of cn900), and its work grate with that tool, but with zed bull just looking for cloner, and sometime 1 in 100 try's start to calculate, and I try to change max232 and some components to, same story, but will try with better cables, that is phone cable those are to tinny, maybe that is problem

[f2f2]

If I remember the big Zed Bull problem
say that one communicational wire can not reach the MAX232 but another half parts go good bond

only good if the MAX232 flawless

send high-resolution images I drawn the correction

My Question : The Quickly device 4C Write to TPX1 and 4D to TPX2 100% okay ? THX

[aandroma]

f2f2 do you have tpx cloner circuit diyagram to make or we ll buy one tpx cloner module??

[f2f2]

429107

Unfortunately I do not have circuit diagrams

but this build it's complicated
You can buy from Asia and works

[aandroma]

can you give us a link to order and buy

[f2f2]

http://www.alibaba.com/trade/search?fsb=y&IndexArea=product_en&CatId=&SearchText=TPX+Cloner

[mikajna]

If I remember the big Zed Bull problem
say that one communicational wire can not reach the MAX232 but another half parts go good bond

only good if the MAX232 flawless

send high-resolution images I drawn the correction

My Question : The Quickly device 4C Write to TPX1 and 4D to TPX2 100% okay ? THX
No, they tell it can, but cant write TPX2, only CN chips and YS...I've try tpx2 and error...tpx3 and tpx4 work like a charm, and also unlocking them after cloning if needed.

[f2f2]

No, they tell it can, but cant write TPX2, only CN chips and YS...I've try tpx2 and error...tpx3 and tpx4 work like a charm, and also unlocking them after cloning if needed.

Quickly...
Yes I also wanted to order but everything is for sale he wrote not PC program for Quickly

So I did not order

[mikajna]

Someone say that its working with tjecu software for cn900/nd900 but I couldnt make working with my tool

[f2f2]

Someone say that its working with tjecu software for cn900/nd900 but I couldnt make working with my tool

I was wondering to Quickly connected with PC
and ID4D chip PC read start
and the data in PC the RESP 2x 48bit visible or invisible
THX

[f2f2]

431055

Zed Bull software ID-4D-xx database TP Read / TP Write

Developed:
1.Read more types of chips (add ID 11-14,33,60-70,4C,40,41,42,44,45,46,48 blank PCF7935 )

2.lower textbox RESP typed data instantly searches a database It has been listed or not

You test... enter these characters 8F or 42 or 2B
Erase 1 character Press Backspace
Erase text box all character press Control+A ; Backspace

[seanortiz]

430287

Zed Bull software ID-4D-xx database TP Read / TP Write

Developed:
1.Read more types of chips (add ID 11-14,33,60-70,4C,40,41,42,44,45,46,48 blank PCF7935 )

2.lower textbox RESP typed data instantly searches a database It has been listed or not

You test... enter these characters 8F or 42 or 2B
Erase 1 character Press Backspace
Erase text box all character press Control+A ; Backspace


why programing in GFA BASIC ?

[f2f2]

Yes GFAwin32 software ( I am the owner with serial number)
Several development programs It is I know this is the fastest Such program to write and filesize small Compared to knowledge.

[f2f2]

430639

The HUNtpRW[46].exe ID46 read/write; select INI file; enable new ini file create and write to chip.
Now all ini file 40 pcs. The CRC16 value can be observed which is an identical operations different cars it is striking.


HUNprecode[PCF7935].exe PCF7935 chip precode from INI text file.
430653

[Skippy32]

Sorry for reviving a nearly year old dead thread, but I was wondering if someone knowledgeable on this topic can help me out.

I bought a zed bull mini clone with no RJ45 connector, so I attempted to compare the pictures that f2f2 left to attempt to solder on the connection. While comparing photos, I noticed that his mini clone has capacitors on the board and mine doesn't.

Can someone tell me if the connection modification can be done on my mini clone? Here is a picture of my mini board for reference:

481150

[ps2chiper]

hey guys, I am interested in setting up a 4d decoder using serial over ip. My goal is to share one decoder for free online. Are any of you guys interested working with me?

[ayhanozdemir1982]

This is a clone device thats why you cann't copy it via pc software.
Orj Zed-BULL device is using server for 4D trasnponder copy.

[ps2chiper]

I have seen people use the hardware module with the clone zed bull. My goal would be to setup one hardware module that can be shared online.

[ciprishor]

This tool only work on Win XP? I try with Win7 64 bit and there is no COM port in the list.

Later edit: I was able to use it in Virtual Machine: Windows XP mode.

The Page Lock bits are one time programmable? Once set is it possible to reset?

[EthicalDeviant]

I bought the Mini Zed Bull because it said it cloned 4D transponders in the description and it was going to be half the price of a new key plus I'd have some fun too. Now I know that it won't clone a transponder on its own. My questions are:

1. Do I NEED a TPX Decoder?
2. If I DO need a TPX Decoder, will that 3-pin cable f2f2 posted a diagram of work for connecting it to my Zed Bull?
3. If I have both of these things, will I be able to clone a Texas 4D 60 transponder for my Nissan?

I downloaded the HUNtpRW[4D] software and it connects to my Mini Zed Bull via my COM5 serial port under Windows 10, but of course, it only reads what the Zed Bull reads with no PG4 information. Can someone knowledgeable on the subject nudge me in the right direction?

(At this point, it would be cheaper to just pay for a new key, but I'm committed to making my own now!)

[f2f2]

I bought the Mini Zed Bull because it said it cloned 4D transponders in the description and it was going to be half the price of a new key plus I'd have some fun too. Now I know that it won't clone a transponder on its own. My questions are:

1. Do I NEED a TPX Decoder?
2. If I DO need a TPX Decoder, will that 3-pin cable f2f2 posted a diagram of work for connecting it to my Zed Bull?
3. If I have both of these things, will I be able to clone a Texas 4D 60 transponder for my Nissan?

I downloaded the HUNtpRW[4D] software and it connects to my Mini Zed Bull via my COM5 serial port under Windows 10, but of course, it only reads what the Zed Bull reads with no PG4 information. Can someone knowledgeable on the subject nudge me in the right direction?

(At this point, it would be cheaper to just pay for a new key, but I'm committed to making my own now!)

Since then there are 2 versions of this program

the other version
Chip Write only unlock **** mode
chip LKP-02 , EH2

[ngakson2002]

Hello Mate,

You need Zedbull with LAN Port.And some big Zedbull are provided with this.As from 2014 all Mini Zedbull are produced without LAN port making difficult to use it with a 4D decoder
If you manage to have a Zedbull with LAN Port ,you will then need a SERIAL-USB cable and a 4D CLONER or Decoder such as the CN900 4D Decoder.The purpose of this decoder is to read the Page4 of the Transponder prior to cloning.

However why having headache in managing to Clone 4D transponder with Zedbull and all these accessories when you have very cheap cloner such as KD-X2 , VVDI Mini Key tool that does this pretty well using the LKP-02, YS-01, VVDI XT27 super mode chip

Best Regards

[XProfig]

Would it also be possible to read/write the EEPROM of ID46 Crypto2+EE transponders (I mean NOT the user data pg4..7)?
As far as I know, this is not possible with Zed-Bull.

Thanks in advance & best regards.