View Full Version : Tmax 2008 mileage correction 93C66
karlos111
4th February, 2017, 02:52 PM
Hi all
I have a tmax dash that needs the mileage changed. The original bin is 47434km and I need 12600miles (20277km)
Thank you in advance
426127
nikz
4th February, 2017, 03:08 PM
here is your file
karlos111
5th February, 2017, 06:01 PM
Hi mate. I'm getting only dots on the mileage and the water temperature gauge goes to max, the fuel gauge stays at min and rev counter is not working. Any idea what may cause that? The eeprom reads and writes as it should. I've uploaded the original file back but still the same.
Thanks in advance!
neospeedo
5th February, 2017, 06:03 PM
sounds like your original is corrupt, i was start searching and trying a different dump
karlos111
5th February, 2017, 06:16 PM
Thanks mate, will try to find a different dump
karlos111
5th February, 2017, 07:10 PM
no luck mate, I've tried 4 different dumps and still the same
zckariya70
5th February, 2017, 07:23 PM
r u writing in incircut ? if u doing in incircut remove the eeprom and write again cheack ur soldering points properly soldered before soldering eeprom, cleane the surface properly, or write back ur orginal and see if u get the orginal km
karlos111
5th February, 2017, 07:50 PM
I'm taking the eeprom off the dash, I've checked the points and everything is as it should be but still the same, I've uploaded the original file but no luck. I guess I'm doing something wrong but I don't know what. I've done quite a few other bikes and never had any problems...until now.
clusters
5th February, 2017, 08:03 PM
maybe blew a small component off the board and didn't notice? Overheated the chip?
karlos111
5th February, 2017, 08:18 PM
All there, the heat is low, I'm using new flux I'm not sure if that might be a problem, I'll try with the old one
sv2hqx
5th February, 2017, 09:55 PM
post a picture of dash!!
karlos111
5th February, 2017, 10:29 PM
Picture attached
thanks
sv2hqx
5th February, 2017, 10:38 PM
looking good maybe eprom destroyed
try this too
karlos111
5th February, 2017, 10:53 PM
Thanks mate, will try it tomorrow and report back
sv2hqx
6th February, 2017, 01:20 PM
Thanks mate, will try it tomorrow and report back
did you get it?
karlos111
6th February, 2017, 04:50 PM
sorry mate, still haven't had time to try it. Will try it tonight
thanks
karlos111
6th February, 2017, 08:37 PM
Not working mate, still the same
sv2hqx
6th February, 2017, 08:59 PM
you should try other eprom
solder points loocking good
dump is original
karlos111
6th February, 2017, 09:28 PM
I've found another dash but I'm worried if I try the eeprim it might get to the same stage
sv2hqx
6th February, 2017, 09:58 PM
I have done a lot of them
If you have clear soldering NP
Just try eprom
Sent from my Nexus 4 using Tapatalk
karlos111
7th February, 2017, 01:14 AM
93c66 is the correct one right? There is one 945b but doesn't look like to be the one for the mileage
clusters
7th February, 2017, 01:44 AM
Yes it is the correct one, the original file you posted looks OK, we can see the original mileage.
If you write back the original file and it still doesn't work, then you have caused a problem that no amount of files will fix.
Try a new chip with the original file or get another dash.
karlos111
7th February, 2017, 07:58 AM
Thanks for the help guys! I'll try with another chip
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.