Please, Need immo on clio 2.0 16v sport ECU sirius 34

[trant]

Hi everybody!!!
Please, I need immo off a sirius 34 ECU
engine is 2.0 16v clio sport swaped in old renault 21.
Originaly it has a/c but i don't need this, trasmision is manual.
The ECU has green wired pin 58, pin 88 is not wired, CAN on pin 27 and 57
part number is:
hw8200057311
sw8200169959
s118303106
Thanks in advance!!!

428652

[Pyromaniak]

Try this file :peaceful:

[trant]

THanks!!!
I'll try and report!

[prusony]

And my version.... (PASS!)

[trant]

Try this file :peaceful:

Car won't start!!!

[trant]

And my version.... (PASS!)

I'll try it tomorow !!!
Thanks

[Pyromaniak]

I have still one, this is very complicated ecu. Good luck!

[hlili2008]

hi
try this file is compatible withall version

NOT:: Cut ECU PIN: 27

428958

good luck

[trant]

I'll try it tomorow !!!
Thanks

car not start!!!

[trant]

hi
try this file is compatible withall version

NOT:: Cut ECU PIN: 27

428958

good luck

is this file for 2.0 16v sport!?

[trant]

car not start!!!


And my version.... (PASS!)
car not start!!!

[skens]

hi
use can emulator if have can ecu!
regards

[Pyromaniak]

If you put ingniton on, goes fuel pump? (for three seconds) I think this ecu is atypic (end of Kline and begining with Can- still have immo line but comunicate with Can) try can emulator like say skens. Or maybe problem elsewhere.

[trant]

If you put ingniton on, goes fuel pump? (for three seconds) I think this ecu is atypic (end of Kline and begining with Can- still have immo line but comunicate with Can) try can emulator like say skens. Or maybe problem elsewhere.

yes, fuel pump goes on but only for about 0.5s, and only before the first cranking, after that, fuel pump is not activated unless disconnecting the battery, I also scan ecu with diagnostic tool, default are: lamda, brake switch, canister.
The rpm is around 150 when cranking seen on realtime data.
How can I know if the immo is by wire or by can!?

thanks to all!!!

[Pyromaniak]

I think its can, because by wire get off with file, and can work with wirgine file (see julia emulator pdf) and ecu save data from a emulator. BR

[skens]

hi
take a photo of pcb,and post
regards

[trant]

Here is the PCB
429217

[ECU2009]

vai con emulator

[trant]

And what about flashing the ECU with wired immo (off) dump??? :burnout:

[Pyromaniak]

I think is not about a flash, but processor. Processor have inside program, if get a data from immo line or can and than compare with flash data, if same-work, if not-not work...


PS: processor have program and he say where data comming from. can or immo line.(for better understanding )

[trant]

So, immo is only possible with emulator!?
but in my case, it hard to find it.
I will connect a CAN dashboard and see how the red led behave!

[Pyromaniak]

So, immo is only possible with emulator!?
but in my case, it hard to find it.

Yes my friend.Search for JULIA emulator, or Renault Can immo emulator.

In all cases red led blinking after immo off :) need to cut wire, or desolder led. BR

[skens]

hi
this is can ecu use can emulator
regards

[trant]

Thanks to all!
I think I will change for a sirius32, put on a vr6 throttle bodie, make it work with renault TPS sensor! I think it's easier and cheaper than buying and waiting for a (right) CAN emulator!!!
regards!

[Pyromaniak]

Dont make change to sirius 32, in ecu you have program (sofware) from renault sport.... If you want a full potencial of this motor, wait for emu... Make photo for this motor swap for me, im interesed with this :D BR my Renault friend.

[okm]

only emulator!!!

[trant]

Dont make change to sirius 32, in ecu you have program (sofware) from renault sport.... If you want a full potencial of this motor, wait for emu... Make photo for this motor swap for me, im interesed with this :D BR my Renault friend.
I've made a few sirius 32 swaped with the Renault Sport dump, immo off-ed, and they all work like original!
I will post photos as soon ass possible!

[trant]

Here is the pic!
430142

[Pyromaniak]

Nice :D good luck!