PDA

View Full Version : Mercedes C200CDI EDC16C2 P2513 OFF



goyodesanctis
15th March, 2017, 06:15 PM
Hi to all!!!
I have make a tune in a customer's car.
It's a W203 Mercedes C200cdi 122hp.
Car has been very fast las two months but today my customer, who has a garage, sent me errors and car doesn't go over 3000 rpm.
Fault code is in M55 and is P2513.
Could anyone delete this dtc???
If anyone needs tune file tell me. Car is very fast and smoke is nothing. I'm going to post ori.
Regards.

lui93
15th March, 2017, 08:59 PM
hello my friend this is fle egr off pass pm thank and reputazion;)

mihaiservice
16th March, 2017, 11:36 AM
Hi
dtc 2513 isnt from egr ! are just from swirl flaps actuator !

goyodesanctis
16th March, 2017, 01:21 PM
Yes, i have blocked by hysteresis maps but dtc shown is 2513 mate,how could I kill this???

goyodesanctis
16th March, 2017, 01:22 PM
DTC is now two months after first remap,sorry. Is not caused by hysteresis.
Regards

goyodesanctis
16th March, 2017, 03:04 PM
Mate is there any solution for this dtc???
How it can be done???

Stig33
17th March, 2017, 02:45 AM
Try this and report....

436177

goyodesanctis
17th March, 2017, 07:51 AM
Hi Mate!!!Is thought by swirl flaps???Is what i need please
If you say yes I will test and I report.
Regards!!!

stanislav georgiev
17th March, 2017, 11:00 AM
It is to have a problem with vortex valves not with EGR

goyodesanctis
17th March, 2017, 03:38 PM
Hola Georgiev !!!
Su 220 CDI Archivo trabaj? fantastic!!!
I don't know where is the problem.
Guy tells me that disconnecting egr actuator car doesn't run in limp mode.
My patience with him is reaching its limit.
Is possible to make egr and flap off???
I think this car is a lot of problems.
I expect don't see it anymore.
Regards mate!!!

Pyromaniak
17th March, 2017, 07:25 PM
I think its from swirl flaps, if you turn off, and open forever, ecu see more inlet air incoming through mass flow meter... Dtc incoming only by idle runing after one minute and motor change sound and is in limp mode. If you start and drive it car runs well, to time where you idling one minute. You need solution for swirl, but i can?t make it. BR


PS: I think for me with this problem HELP user bobolin4o

goyodesanctis
17th March, 2017, 08:05 PM
I think its from swirl flaps, if you turn off, and open forever, ecu see more inlet air incoming through mass flow meter... Dtc incoming only by idle runing after one minute and motor change sound and is in limp mode. If you start and drive it car runs well, to time where you idling one minute. You need solution for swirl, but i can?t make it. BR


PS: I think for me with this problem HELP user bobolin4o
Yes. Problem is with flaps. Have I to contact this user?
Thank you very much

bobolin4o
18th March, 2017, 07:57 AM
Yes. Problem is with flaps. Have I to contact this user?
Thank you very much


Here is your file... You have to disconnect the M55.
NO CHECKSUM!

goyodesanctis
29th March, 2017, 08:36 AM
Thank you thank you thank you!
Car second time had p2527 error. In egr too. Now no errors and works perfect!
Cheers!