Renault Scenic ll Injector coding with Galletto4 how to?

[Aivis3]

Renault Scenic ll Injector coding with Galletto4 how to?

1.9L F9Q engine
0281011549

1 - AAAAAA
2 - AAAAAA
3 - AAAAAA
4 - AAAAAA

Need:
1.cyl from gearbox side?
1 - ASRYB6
2 - 78H1CX
3 - B1AAF0
4 - BIAGFT (I or L ???)

437835

[smirnoff_rules]

l dont think you can edit these ,l have one with normal codes ie not AAAAA , l believe any codes will work as long as there not AAAAAA
not sure about your chassis number tho . worth ago
unzip and try

[Aivis3]

Thanks, but my file is same...

[morgano]

Hi.

I think @smirnoff_rules file is same, try this ;)

Regards,

[Aivis3]

get writing error..
not possible to write any edited file. After 50% - ERROR
But when I write my file with AAAAAA - OK
Maybe eeprom checksum?
I will try to reed full BDM.

[Aivis3]

Full BDM

437875

How to repair eeprom?

[666_devil]

Did you try writing them with renault clip diagnostic?

[Aivis3]

The problem is that the Renault Clip not available. :(

I was tried with Delphi and Galletto4

Need a solution with EEPROM...

[smirnoff_rules]

have you tried deleting fault codes before writing inj file

[alcorte]

autocom or delphi, firts cleanear dtc, and then you can code the inyecetors.

[Aivis3]

autocom or delphi, firts cleanear dtc, and then you can code the inyecetors.

DTC can not be deleted!

[ollync]

DTC can not be deleted!

Post DTC


Sent from my iPhone using Tapatalk

[pulsar2000]

Dtc can be deleted with X431. Then Do not attempt to start car ! then recode ingectors using Delphi or X431,
i had similar issue NISSAN X TRAIL, could not even start car as DTC ECU Chain of command - like immo because no inj codes,

Other thing to try. this should also work.

Write Original file back. Do not start car after until you write back original inj codes that were backed up with FGTECH.
should write back ok back up, then car all ok again,

If you didnt back up with fgtech using inj backup, dont think will work,
Complete BDM only way, dont know why but eeprom gets corrupted and loses codes amd wont allow recode.
After bdm will allow coding as eep ok, then you can recode manually using delphi or LAUNCH,

[ominimi]

when i got injectors decoded i can start car but wont pass 1500 rpm, delphi did it in a moment

[Aivis3]

Solved! Thanks!

[bobolin4o]

I realy don't understand why people have troubles with this inj. coding...
The most important thing is to read the inj. codes BEFORE reading the flash! Galetto says this every time when you make ID!!!
After reading the flash inj. codes are already ~~~~ed... This is not a problem if you have them already.
Just flash your mod file, then cycle ignition off/on, do not start the car, write inj. codes, cycle ignition again, erase the DTCs and voila...

[Aivis3]

Some people realy need a glases, some dont understand english... :chuncky:

[Bllinda]

I can find as you succeed programmed jets?
In this da (http://www.digital-kaos.co.uk/forums/showthread.php/584913-Renault-Scenic-ll-Injector-coding-with-Galletto4-how-to?p=2988882&viewfull=1#post2988882).mp (http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=437875&d=1490295841) programmed jets?

"Need:
1.cyl from gearbox side?
1 - ASRYB6
2 - 78H1CX
3 - B1AAF0
4 - BIAGFT (I or L ???)" Thank you

WBR

Bllinda

Solved! Thanks!

[Aivis3]

I can find as you succeed programmed jets?
In this da (http://www.digital-kaos.co.uk/forums/showthread.php/584913-Renault-Scenic-ll-Injector-coding-with-Galletto4-how-to?p=2988882&viewfull=1#post2988882).mp (http://www.digital-kaos.co.uk/forums/attachment.php?attachmentid=437875&d=1490295841) programmed jets?

"Need:
1.cyl from gearbox side?
1 - ASRYB6
2 - 78H1CX
3 - B1AAF0
4 - BIAGFT (I or L ???)" Thank you

WBR

Bllinda

1 - ASRYB6 (Gearbox side)
2 - 78H1CX
3 - B1AAFO (O, 0-coding not accept)
4 - BIAGFT (I )

possible to upload the injector dump only once, after EDC16C3 dump read... (Galletto)

438220