mazda cx 7 fap and adblue remove probleme

[youssefi201]

hi freind please i need help for mazda cx7 ecu ref R2AX-188K1-B i remove fap and adblue with swiftec soft but lamp stay on
anyone can help me
HW R2AX-188K1-B
SW R2AX-18881-L
SW VER R2AX-18881-J
thanx
this is original file and modified file

[alonedark]

send the file to swiftech

[mariusica_boy]

hi freind please i need help for mazda cx7 ecu ref R2AX-188K1-B i remove fap and adblue with swiftec soft but lamp stay on
anyone can help me
HW R2AX-188K1-B
SW R2AX-18881-L
SW VER R2AX-18881-J
thanx
this is original file and modified file


What error do u have with swiftec file?

[tricore3]

your file off dont forget thanks and reputation
report when you upload.

for me work 100%

[youssefi201]

thanx freind for your help but lamp stay on and message adblue to low

[tricore3]

reset dpf and adblue with scan tool
if that way dont work
refill to minimun the adblue and test it

[mihaiservice]

Hi
the adblue level can not be reset when level sensor are damage ! you have to emulate level sensor with one 560-680 ohm resistor !

[mariusica_boy]

hi freind please i need help for mazda cx7 ecu ref R2AX-188K1-B i remove fap and adblue with swiftec soft but lamp stay on
anyone can help me
HW R2AX-188K1-B
SW R2AX-18881-L
SW VER R2AX-18881-J
thanx
this is original file and modified file


Your file with dpf off and adblue off 100% working solution.
Write my file.Disconnect ecu for Adblue. Location it is under the divers chair.
Reset oil service intervals and its done.

Pass PM.

[youssefi201]

thanx freind but alwys lampe on its unnatural IM TRYING WITH 3 FILE AND SAME PROBLEME
unnatural

[mariusica_boy]

thanx freind but alwys lampe on its unnatural IM TRYING WITH 3 FILE AND SAME PROBLEME
unnatural

mate, what error do u have?

[youssefi201]

Diagnostic no dtc
but lampe in dash blinking and message adblue to loW i tried reset function but no success

[mariusica_boy]

Diagnostic no dtc
but lampe in dash blinking and message adblue to loW i tried reset function but no success

u disconnect connector from ecu adblue?

[youssefi201]

yes under driver chair

[youssefi201]

hi again Ii I wrote the file and after reading the file I noticed that two line not change is what it can be the cause ??????

[duco]

hi to everybody
somone can help me to make adblue and dpf off on this file?

Numero Hardware: R2AX-188K1-B
Numero Software: R2AX-18881-L
Software di aggiornamento: R2AX-188K2-L

i have light on level adblue

thanks in advance

M.451919451919

[alea99]

Hi, the resistence 550-680 is between Reference sersor (Grey) with deep sensor (Blue)?, In serial or in paralel with the resistence in the container?

Thanks in advanced.

[macako6]

hi to everybody
somone can help me to make adblue and dpf off on this file?

Numero Hardware: R2AX-188K1-B
Numero Software: R2AX-18881-L
Software di aggiornamento: R2AX-188K2-L

i have light on level adblue

thanks in advance

M.451919451919



Your file DPF SCR off

1. Remove the DPF filter
2. Reset DPF (with diagnostic)
3. Reset oil service interval (with diagnostic)
4. Remove the one fuse in the engine compartment (SCR fuse)

[alea99]

[QUOTE = mihaiservice; 3026336] ¡Hola,
el nivel de adblue no se puede restablecer cuando el sensor de nivel está dañado! ¡Tiene que emular el sensor de nivel con una resistencia de 560-680 ohmios! [/ QUOTE]


Hi, the resistence 560-680 is between Reference sersor (Grey) with deep sensor (Blue)?, In serial or in paralel with the resistence in the tank?

Thanks in advanced.

[pocinas]

Anobody knows between which color signal must be used Resistor 560-680ohm? to reset tank level

[Ivana31]

Hello, I have solution for this car.. I spend 1 week to fix this problem. Please contact me on skype (we need realtime communication) andrej_deskovski

Regards

[pocinas]

Ivana, i was contacted with you and we was chat and call on skype.

I Think it will be hard for me find another tank to borrow and do Reset level fluid adblue, so i starting as well find alternative, if is.