BMW E60 2006 LCI Milage correction

[kubuswujo]

Hi!

I do have an BMW e60 LCI 2006 for a milage correction, on Digiprog i do have 4 instructions, how to know what to use for it?
white black is a color of CAS?

There is a milage in TACHO in CAS and somewhere else?
Is there in key also? what if i will not change it in KEY?

Should I use better DIGIPROG 3 or CARPROG?

(I have a new 3580 Eeprom)

Thanks
Kuba

[Nicolas9]

you need tacho+cas. but digiprog cannot do cas 2006.

you need r260 or r270

[kubuswujo]

Yes I do have R270+ with eeprom remover. any instruction? Or just take eprom out, delete eeprom, change milage, write eeprom?

First do CAS or Tacho? I think first CAS than TACHO

[memet99600]

Yes I do have R270+ with eeprom remover. any instruction? Or just take eprom out, delete eeprom, change milage, write eeprom?

First do CAS or Tacho? I think first CAS than TACHO

Save before erase eeprom, and cas make after with 0km drive 50km with each key for synchronisation

[kubuswujo]

You have said that Digiprog wont do Cas but i do have an istruction to white CAS that i have in my BMW.

What is CAS Diagnose for in PDF that I attachment shouldn't I tried it??

Shouldn't I do it with DIGIprog3? And i should do only with R270 yes?



453851
453853

[memet99600]

You have said that Digiprog wont do Cas but i do have an istruction to white CAS that i have in my BMW.

What is CAS Diagnose for in PDF that I attachment shouldn't I tried it??

Shouldn't I do it with DIGIprog3? And i should do only with R270 yes?



453851
453853

Digiprog 3 can only do cas3/3+ by obd. The instruction is for original digiprog not china clone.
Do the job with R270+ it's safe and easier

[kubuswujo]

Ok will do it with R70 as You advise. Here is an oryginal dump from TAcho e60, can someone edit it to 182 000 KM?

453883

[sida]

here...453886

[kubuswujo]

Hi thanks!!

I my m35080VP was blocked and cannot erese it with r270 but i had take the 080D0WQ from dash from e90 and have eresed it writen with file from sida. Hope it will work.

Now i have a question, how to connect r270 with CAS2 white? i didn't have any instruction for connecting pins with r270.
Someone have it?

or should i desolder sth?
Ododmeter in Cas should be 0km?


EDIT:


Ok i have find it and know why have no picture

I have a R270+ on Windows XP and it does not read (read till 922/1024) have installed it on windows 7 and work read/erase/ write.

But didn't have pictures (no picture go)


but i opened the R270+ on widnows XP and go to MCU >>2k79x> and now have the picture.



And have seek it didn't work beacouse i have seek on windows 7 where the program do not have pictures.






But now have other problem i have find how to solder pins but when i make read 2K79X with laptop on Widnows7 (which I read and erase 35080) I get:

UnKnown 9s12 ID!
Maybe is 912 MCU
ID: 0x0000

and when i do it the same with Windows XP laptop, then t goes throught ID and make Id 0x00012 (OK) but then stars reading with this (wait1-3 minutes).

And nothing happend..


Any advice?
Try on another laptop?

[memet99600]

use this thread it's very helpful with R270

http://www.digital-kaos.co.uk/forums/showthread.php/266618-R270-new-software-1-20?p=1527260#post1527260

[kubuswujo]

Hi Thanks!!

I have reistal Abrites on Windows XP and R270+ started to work.

I have read the EEPRom FROM CAS2 and edit it with R270 to 0 milage then write. Everything without errors.
But when i go to car, i will not START;/;/;/;/
If i look on the dash i have the RED CAR on SERVICE LOGO ;/;/;/

I have tried to RECOVERY CAS2 with orginal EEprom file it goes ok on computer but CAR still do not wont to start.

I add an orginal FILES from FLASH and EEPROM FROM MY CAS2:
454011
454012


I do not now what to do now?
1. Should I make TACHO also oryginal file will it bring sth? (in tacho is no immo etc.;/;)
2. Should I buy another CAS2 and reprogram FLASH and EEProm with file from my CAS2?
3. Any other advices?


Thanks in advance
Kuba

EDIT:

If i want to buy Another CAS from internet and wait what should i look for?
CAS 2, white color, HW. 03?
whats more?
PArt number must be the same?


Is it possible to repair my CAS? without waiting till monday on CAS2 Shipping?

[Tefocm]

Hi
kubuswujo (http://www.digital-kaos.co.uk/forums/member.php/496048-kubuswujo), please note BMW uses V6 eeprom, you have to replace with new one...

[memet99600]

I think flash corrupt because car not start maybe someone can repair it

[kubuswujo]

Ok so one more @Tefocom:
You think that I should replace only the V6 Eeprom or the whole CAS2 and reprogramm it?

@memmet99600:

You think that Flash is broken (an item) or the dump that i read from Flash is bad??
I can pay if someone will repair the flash dump and the car will start.
Do You know anyone from DK who can make this?

The dumps EEprom and flash are those before writing.


I must add that i have read EEprom and edit to 0km, write and then go to car>> will not start ;/;/ >> so solder pins one more time and then have read the Flash.

[memet99600]

@memmet99600:

You think that Flash is broken (an item) or the dump that i read from Flash is bad??
I can pay if someone will repair the flash dump and the car will start.
Do You know anyone from DK who can make this?

The dumps EEprom and flash are those before writing.


I must add that i have read EEprom and edit to 0km, write and then go to car>> will not start ;/;/ >> so solder pins one more time and then have read the Flash.

No needed to pay someone will fix it don't worry someone will repair it, they just need to see your message ;) or give you a flash for this CAS. I think just bad read flash but i'm not sure.