Can't read Motorola ok75f hc912d60

[borshch]

First time trying to read mcu.

ford f250 2003 trying to do odometer mileage correction
mcu
motorola xc511301vpv8

ok75f
hhth0211

Apparently HC912D60 112pin

tried with carprog a10 adapter.
cant read.
checked all wires, eveything matches correctly even inside the adapter I checked.

carprog does 5 attempts and cant read it. Htz Frequency is 4000khz


and in xprog i get "device is silent"

im pretty sure I connect all 4 wires correctly. What can I be doing wrong ?

[jomberykaso]

upload pictures

[automotrizVIP]

upload pictures
http://www.digital-kaos.co.uk/forums/showthread.php/288164-NEED-DUMP-FORD-CONNECT-2002-YEAR

[borshch]

https://preview.ibb.co/kZRutF/IMG_20170605_134028948.jpg (https://ibb.co/i8qb7a)
https://preview.ibb.co/dsEQ0v/IMG_20170605_134041116.jpg (https://ibb.co/iP2pSa)
upload my pictures (https://imgbb.com/)

[epd1221]

Why dont you try reading straight from points ..

[automotrizVIP]

Edit". Double pulse clip and double posting sorry ......

[automotrizVIP]

454925..............

[borshch]

454925..............

Yea that's what I selected in carprog and in xprog and can't read it...

[borshch]

Why dont you try reading straight from points ..

That's what I'm doing. No ?

[automotrizVIP]

XPROG USE BM
455058

CARPROG CONECCTION USE A10
BLUE- RESERT
BROWN- GND
GREY- BKGD
RED - +5V
VIOLET - +12V
455059

[borshch]

XPROG USE BM
455058

CARPROG CONECCTION USE A10
BLUE- RESERT
BROWN- GND
GREY- BKGD
RED - +5V
VIOLET - +12V
455059

Thank you. Will try again. Will report

[borshch]

XPROG USE BM
455058

CARPROG CONECCTION USE A10
BLUE- RESERT
BROWN- GND
GREY- BKGD
RED - +5V
VIOLET - +12V
455059

Where does the 5th connection go with carprog a10 to the mcu ? It only shows 4 connectors on the picture but a10 has 5 wires that supposed to be connected

[automotrizVIP]

Where does the 5th connection go with carprog a10 to the mcu ? It only shows 4 connectors on the picture but a10 has 5 wires that supposed to be connected
Do not use 5 cable... (12v)....

[epd1221]

Friend read it like the picture i post. With xprog or carprog. It should be good

[FxShaw]

Solder the wire exact like this using A10. read under dash-ford-direct-f250 and done

[borshch]

Why dont you try reading straight from points ..

tried with carprog error: "shotcircuit. current more than 500ma". checked eveything. no shorts tho

[borshch]

Solder the wire exact like this using A10. read under dash-ford-direct-f250 and done

this f250 cluster 6 solder points on the front or back of the pcb ? the ones on this cluster look little different

[borshch]

disconnected 12v power form carprog, no more shortcircuit error but carprog goes attempt 1,2,3,4,5 and cant read the chip

[borshch]

XPROG USE BM
455058

CARPROG CONECCTION USE A10
BLUE- RESERT
BROWN- GND
GREY- BKGD
RED - +5V
VIOLET - +12V
455059

my xprog is probably junk. goves error "bootloader initialsising error. cant access BDM. check BDM connection"

[FxShaw]

disconnected 12v power form carprog, no more shortcircuit error but carprog goes attempt 1,2,3,4,5 and cant read the chip
Using 12v input into carprog was a big no no. You can use the 6 point on the back.
Here is an idea...how about you post a picture of how you solder to the board and upload it.

[borshch]

455515
brown = ground


Using 12v input into carprog was a big no no. You can use the 6 point on the back.
Here is an idea...how about you post a picture of how you solder to the board and upload it.

[FxShaw]

brown = ground

Gray wire where green goes, and purple? wire has to be red.
if its a clone A10 adapter then the colors might be wrong on the adapter it's self...possibility

[automotrizVIP]

455536
check A10.....................

[borshch]

Gray wire where green goes, and purple? wire has to be red.
if its a clone A10 adapter then the colors might be wrong on the adapter it's self...possibility

455727
this is inside a10 connector

[narkeleptk]

black as the kline and not ground? might be normal for that tool but man that is confusing.

[jomberykaso]

buy Upa clone and you will have a happy end

[borshch]

So do I connect correctly to the mcu with carprog a10 adapter ?

[radugcr]

You need to connect Xtal to read with Xprog M because mcu is secured.

[borshch]

Im trying with Upa-s USB now, can't read it either :(

[castin]

Mate, its simply MCU for read - only 4 wires. Check You A10 adapter, use pinout on dash pcb and must work. In carprog check seting for corretly mcu type.

[narkeleptk]

You need to connect Xtal to read with Xprog M because mcu is secured.
Its not. You only need vcc,gnd,rst,bkgd


Im trying with Upa-s USB now, can't read it either :(
This is very simple processor to read. I think your main issue here is your using poor quality tools. clones of clones no doubt.

what version of xprog do you use? Do you use it to read other 9s12 before?

[narkeleptk]

455515
brown = ground

This is all wrong if your using the a10 adaoter you posted.

Should be (assuming you got ground pad right)

VCC 0 0 X
RST 0 0 X
GND 0 0 BKGD

on your a10 adapter
RST =blue
VCC =red
GND =brown
BKGD =grey

[epd1221]

With UPA how are you connecting if it cant be read ?? Its a very simple connection 4 wires select mcu and done ..

[mariusz971]

To post #4. Borshch, you are on the wrong side,. Verify pin #1

[borshch]

Solder the wire exact like this using A10. read under dash-ford-direct-f250 and done
Do you know which wire color is which by description ? I think on my adapter the colors are different

[narkeleptk]

Do you know which wire color is which by description ? I think on my adapter the colors are different

schematics for adapter can be found on tools site codecard.eu