View Full Version : Edc17cp45 bmw drill
beltronics
20th June, 2017, 06:16 PM
Hello
I have an ECU Edc17cp45 from BMW to make and I need to know the measures in which I have to drill the ECU.
I have to do 2 guajeros, one for boot and one for the GPT cables but I do not know the distance that I have to do.
Does anyone have that info?
Thank you
orange123
20th June, 2017, 06:54 PM
open ecu on both sides that is the save way.
aem
20th June, 2017, 07:17 PM
lol :)) who open that ecu is crazy......is multistrat pcb...one bad move and you can shot yourself....
mariusica_boy
20th June, 2017, 07:36 PM
Hello
I have an ECU Edc17cp45 from BMW to make and I need to know the measures in which I have to drill the ECU.
I have to do 2 guajeros, one for boot and one for the GPT cables but I do not know the distance that I have to do.
Does anyone have that info?
Thank you
Here u go mate....
teerak2uk
20th June, 2017, 07:40 PM
What about metal particles that you can't get out when they drop inside
aem
20th June, 2017, 07:51 PM
there is no particles inside.is not drilled to the end.....is drilled untill you can force piece to broke....in this way you can put it back with seal after read write.
if is not ok like this you can buy special tool from magic motorsport :) is only 260 usd :)
mariusica_boy
20th June, 2017, 07:52 PM
there is no particles inside.is not drilled to the end.....is drilled untill you can force piece to broke....in this way you can put it back with seal after read write.
Exactly... do not need to drill to the end.
DAF2000
21st June, 2017, 10:41 AM
What tool did you use for drill,and aprox.distance?Thanks
Sent from my SM-G920F using Tapatalk
topclef
21st June, 2017, 10:58 AM
enjoy !
https://www.youtube.com/watch?v=_8EzkOlLtFQ
PowerPlus
21st June, 2017, 04:40 PM
easy going :applause:
https://www.youtube.com/watch?v=mUOrKiZzIL0
https://www.youtube.com/watch?v=5HZYpiEwGaI
:applause:
use THANKS button
smirnoff_rules
21st June, 2017, 04:59 PM
whats the name of a drill with a hole in the middle ?
teerak2uk
21st June, 2017, 05:31 PM
Holesaw .
smirnoff_rules
21st June, 2017, 05:46 PM
no not them its looks like a drill bit but has a hole in the centre
teerak2uk
21st June, 2017, 06:01 PM
Hmm never seen one a drill with a hole in the middle can't drill as there is no cutting part in the middle
daniel guerra
22nd June, 2017, 06:18 AM
Annular cutters
https://advancedrills.com/annular-cutters/
smirnoff_rules
22nd June, 2017, 06:28 AM
Annular cutters
https://advancedrills.com/annular-cutters/
yea thats the type l was talking about just ordered one to test
https://i.gyazo.com/e64b24a36f8925e6319cd3df45b9a4a3.png
pulsar2000
22nd June, 2017, 06:37 AM
surely not as in Photo mate, looks like masonry Drill bit that one,
I was told Engineering Flat drill also, and can see the logik of drilling untill able to press out the disc,
think i would try if had correct Drill for job, makes it harder as ribs in the case so need a jig to hold Ecu and Drill (pillar drill and clamp would work)
viercha
22nd June, 2017, 06:51 AM
https://www.youtube.com/watch?v=nn8H8l2fgB0
better version
smirnoff_rules
22nd June, 2017, 07:03 AM
no its listed for metal , l have a piller drill . my idea is that if l drill till its just about to go though and then stop and use the bit in the middle that isnt drilled l can leaver that out and not bits will go in ecu
just the same as the video that was posting while l was writing this lol
teerak2uk
22nd June, 2017, 07:39 AM
yea thats the type l was talking about just ordered one to test
https://i.gyazo.com/e64b24a36f8925e6319cd3df45b9a4a3.png
But don't this use a pilot drill that sits in the centre to keep it central of which the pilot drill will protrude 5mm+ at least?
smirnoff_rules
22nd June, 2017, 08:08 AM
can use without it says , with ecu locking in place and cut fin off , its only alloy after all , l will do it close to the bin so l can throw it all in there if it dosnt work
teerak2uk
22nd June, 2017, 08:19 AM
Do you know exact drilling area?
Also don't forget the video😁
smirnoff_rules
5th July, 2017, 08:46 PM
well the drill works great . just testing today , not one bit went into ecu .. worth ?2 lol
https://i.gyazo.com/07909e41d727b8f2404a41ecd383afc0.jpg
https://i.gyazo.com/dd5afcff2f4218085e3f0da0080de65b.jpg
https://i.gyazo.com/916897d09fe712540455aa8aef358449.png
https://farm5.staticflickr.com/4061/35740305825_01bb2402ab_b.jpg
ebay 16mm http://www.ebay.co.uk/itm/15-45mm-Carbide-Tip-Tool-Stainless-Steel-HSS-Drill-Bit-Metal-Cutter-Hole-Saw/262691714038?ssPageName=STRK%3AMEBIDX%3AIT&var=561612547300&_trksid=p2057872.m2749.l2649
daniel guerra
5th July, 2017, 09:02 PM
Great work Smirnoff!!!
pulsar2000
6th July, 2017, 08:46 AM
Yes Good insight, always at it smirnoff, Great share :applause:
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.