Audi TT 999999

[diagtech]

Hi could someone have a look at this file from audi tt showing 999999 customer is unsure of original miles around 200000 i need 105,100 and checksum repair tried with digiprog and carprog comes back with unknown version thanks.

[Nicolas9]

Did you try the option M73 in digiprog? (By obd)

[naprawa5]

Try it audi tt 105100

[diagtech]

Thanks mate but still the same 999999

[bersch8688]

Read PDF
Digiprog do it!

[diagtech]

I have read the pdf but it is unknown version

[diagtech]

And i only have cluster someone has sent to me thanks

[naprawa5]

Did you try digiprog 3 repair 999999 and it does not work?
I did it several times and it always worked.
Digiprog fixes checksum.
You need to use the 41 cable.

[diagtech]

Hi yes tried all that just shows unknown version

[naprawa5]

Try this, crc should be ok.

[diagtech]

Thanks but still 999999

[dominik.m]

Hi. If You want try this file. Should be ok.

[salkapone]

here is similar o.k dump with known pin,,write this and adapt with diag to car ,,and adapt keys!!!!

[diagtech]

Thanks for that but managed to sort it thanks

[nikz]

Can I see a good dump ???

[salkapone]

o.k can you upload moded dump....that what is o.k now...thanks

[diagtech]

Here Is dump from fixed dash

[andye26]

Hi here is a couple of files I made which fix the 999999 just copy all data excluding AA and paste in damaged 912dg128 eeprom.
This will set mileage at 0 Miles which can then be set to correct mileage with a valid CRC.
Included both types of file I have found in these Clusters just pick the one matching your file layout

Regards
Andy

[mundollaves]

HELLO, I HAVE TESTED THE TWO FILES, CHANGING EVERYTHING ABOUT MY BAD FILE, EXCEPT AA, IT DOES NOT WORK IN MY CASE, CAN ANYONE HELP ME IN MY CASE?


THANKS IN ADVANCE.
DASH REFERENCE 8N1920930R 3K91D

[tigar]

Hi
CS is 000450 old 000440

[rosak]

Hi here is a couple of files I made which fix the 999999 just copy all data excluding AA and paste in damaged 912dg128 eeprom.
This will set mileage at 0 Miles which can then be set to correct mileage with a valid CRC.
Included both types of file I have found in these Clusters just pick the one matching your file layout

Regards
Andy

Thank you very much Andy, your files are very helpful. My DP3 just died and I'm waiting for a new one so couldn't do the job without your help.

[audi tt]

Hello I am the bino of Portugal, this is the first time I am on the forum, I would like to thank you for your help. Thank you

[audi tt]

i have audi tt 2003 1.8 180hp, with the same problem i went to a specialist and i was unable to solve the problem, i have a digiprog machine that i bought with all the st 41 cables and the others, but i don't understand anything how to work with it. and how to fix my 999999 car error. could help step by step how to do it. I was very grateful. Thank you

[Cllau]

Hello I am the bino of Portugal, this is the first time I am on the forum, I would like to thank you for your help. Thank you

hi mate and welcome to the wonderful community of DK, open dash and post a photo of your board, if is MM i'll assist you with instructions step by step....:driver:

[audi tt]

mr. Do not mind sending it to me as you did to solve the 999999 problem, I really know how to solve it in my car and need step by step how to do it. I was very grateful. Thank you

[audi tt]

how do i do this callu excuses my ignorance.

[audi tt]

cllau is this what you mean 8n1920930q? thank you​

[audi tt]

a máquina que comprei foi o digiprog 3 com cabo st41.​

[Cllau]

photo means picture not serial nr.... here is a pic of a MM dashboard, open dash means remove cluster from car and open to see inside the electronic main board....
.................................................. .754445

[Cllau]

a máquina que comprei foi o digiprog 3 com cabo st41.​

you choose to break the rules, read rules mate... only english allowed... i'll advice you to go true all::rulez:
:wink:


https://www.digital-kaos.co.uk/forums/showthread.php/2-FORUM-RULES


29.English is the only acceptable language on the forum.Please adhere to this,to avoid unnecessary confusion to other members,And to allow the staff to be able to moderate the forums.

[audi tt]

thank you for your help, and excuse my ignorance. I will disassemble the mcu and I will post his picture. Thank you

[Cllau]

thank you for your help, and excuse my ignorance. I will disassemble the mcu and I will post his picture. Thank you

only the back cover don't touch the mcu.......:palm2:

[audi tt]

754468754469754469cllau eu sou realmente um nabo loldesculpe novamente minha ignorância. é isso que você precisa?

[audi tt]

cllau i'm really a turnip lol sorry again my ignorance. is this what you need?​

[audi tt]

754471
esta mais foto cllau.

[audi tt]

I will send you the photo of cable st41 and the video of the error you are giving me. thank you

[audi tt]

754475como conectei o cabo st41 ao quadrante.

[audi tt]

754476

this is the error that you are always giving me, not even the kilometers i can get give me error 999999 right away.

[audi tt]

cllau think you can help me.

[naprawa5]

Check the cable making.

[audi tt]

naprawa5 obrigado pela ajuda, eu confirmei e os cabos estão corretos.

[audi tt]

I'm going crazy about this.

[Cllau]

compare your plug wires with post#40 diagram..... possible the plug or your tool gives you the error... if the plug wire matches the pins then your clone cannot do this car...

[audi tt]

cllau is talking about the diagram that naprawa5 sent me, right? or the diagram from digiprog where do i plug the st 41 cable?

[audi tt]

if it is the diagram that naprawa5 sent me from cable st 41 mine is the same and in digiprog i have the audi tt menu of the year of my car.

[Cllau]

if it is the diagram that naprawa5 sent me from cable st 41 mine is the same and in digiprog i have the audi tt menu of the year of my car.

then your clone Digiprog3 can't do this car..... read eep and upload here, maybe someone will fix the dump ...:driver:

[audi tt]

then your clone Digiprog3 can't do this car..... read eep and upload here, maybe someone will fix the dump ...:driver:

cllau can you help me to read epp to post here. how to do step by step. Thank you

[Cllau]

your digiprog3 clone will not read that mcu mate, you need a different tool to read, like upa, carprog or vvdiprog.... :driver: or find someone in your area to fix this for you....

[audi tt]

and if I buy another quadrant, isn't it better?

[audi tt]

but why is it not possible to read eep cllau with my digiprog, I have this function
but why is it not possible to read eep cllau with my digiprog, I have this function

[Cllau]

use search on this forum and you will find a lot information about your tool, NO, your tool does't have this function to read MCU, some can be programmed directly but not read and save to be edited ... It's a cheap clone that's why, for a professional job you need skill and more than one professional tools .... :driver:

[audi tt]

please help me how to read eep with my digiprog?

[Cllau]

:palm2::listen:.....................:vroam::giveup :

[Diagcar1]

please help me how to read eep with my digiprog?

Can't you read??????

your digiprog3 clone will not read that mcu mate

[catalinosonesti]

please help me how to read eep with my digiprog?

Hi
Cllau ,have right ,you need profesional tolls to do your job .
Do NOT try by Obd
http://www.codecard.eu/carprog/software/dashboard/s7-20-dashboard-repair-by-obdii-for-audi-a3-tt-r8-new-2010-/prod_772.html

Read this ,and you understand

[volorucinski]

Hello. Btw, maybe I am not on the right topic... I have MM4, ipc from A4B5 facelift. 2001. Ipc with minidot, and 9s12. Is there a chance to read it with UPA? My carprog is not reading 9s12, and i don't know for sure if this 9s12 has security or not. UPA reads only 9s12 without security protection... Thank you for an answer...

POST EDIT. I have just found the answer, here. Sorry for interruption... https://www.digital-kaos.co.uk/forums/showthread.php/187183-Audi-A4-MM4-4-B0-920-900
What I am willing to do now is try copying the 9s12 dump from a petrol ipc and put it onto a diesel ipc. Let's see if it can be made. I have the ipc foil and some leds to replace there...

[d146]

hallo guys i need your help.

This cluster has the original dump under checksum but the MCU by motorola is broken

I bought a new one, but when i replace the dump,show me 999.999km.

Can someone help me?

Please is urgent

many many many thanks

I need 219687km.

[Domi]

try............

[d146]

No mate,999.999km yet

[Domi]

again................

[d146]

My friend,ask me a password

[d146]

Nobody know the solution??

Please help me!