ford ranger 8c pin

[KILL_THE_IMMO]

hi there
please friends i need pin code for manual programming
this is dump from ecu 95320
thanks

[KILL_THE_IMMO]

the dump is it good or not?

[bigkey]

hi there
please friends i need pin code for manual programming
this is dump from ecu 95320
thanks

Not quite sure but Tango give me the pin code 00000000
(See attachment) May need other experts to explain :tears_of_joy:467881

[KILL_THE_IMMO]

i made a chip from immobilizer and lamp go off
this is pin 55129964
but car wont start because the ecu dump touched by sameone before


can sameone repair it
what doing to synchro immobilizer and ecu?
thanks

[virus900]

How did you program key from immo dump and how can i Find pin for it

[KILL_THE_IMMO]

How did you program key from immo dump and how can i Find pin for it
FROM IMMOBILIZER MATE

[KILL_THE_IMMO]

anyone have a full set for this ranger wlas ecu

[KILL_THE_IMMO]

still need help plz
this is my story
the car is all key lost
sameone touched ecu 95320 dump and make it virgin (maybe) so when i read this chip it show code 00000000
the owner of this car bought 2 virgin key from dealer
to readpin i pulled out immobilizer and programed a new chip
but car still dont work immo light illuminated and cranck but with kts it write me antitheft problem
i tryed to program the 2 other key manually but without success after finishing entering wordcode light still solid
plz any suggestion?; any help?

[Weasel3]

I see that it also exists a Siemens BNX2 5WS40139D-T from 2007- with ID63 - 93C56.

Ford:
F-100
Fiesta
Focus
Ranger 2007-

[klaudio]

still need help plz
this is my story
the car is all key lost
sameone touched ecu 95320 dump and make it virgin (maybe) so when i read this chip it show code 00000000
the owner of this car bought 2 virgin key from dealer
to readpin i pulled out immobilizer and programed a new chip
but car still dont work immo light illuminated and cranck but with kts it write me antitheft problem
i tryed to program the 2 other key manually but without success after finishing entering wordcode light still solid
plz any suggestion?; any help?

I read your dump, you should be able to add a key with tango. After programming it ask to program immo box as well that's where the problem is. You got two good dumps, both have different pin numbers, so I don't think you will be able to do it that way, program the key on the two dumps and try. 8C is your transponder.

[KILL_THE_IMMO]

the last dump uploaded by me is from a donor i entered pin in it

[klaudio]

Your first dump is good, tango recognize it as a ranger, the second is recognized at a different vehicle, you mention virgin key, not sure what that means, never heard of that. Anyway try tango with your dump and try to program your virgin key to it, it will ask to program the immo unit as well, I imagine is the same eeprom number as the ecu, I've not done one before, I am just offering suggestions. Maybe someone will be better help.

Good luck.

[KILL_THE_IMMO]

any one have a full set bdm and immo dumps for this shit

[Mohammedananew]

Hi , i can help you to resolve the ford ranger 8c

[Mohammedananew]

i have both ecu and immo , ecu with 95320 but dont know what is the immo eeprom number

[szkeptmen]

There is a HC 805 P 18 inside...
TMpro can read it.

[KILL_THE_IMMO]

read 95320 and pull code and program key with this code

[KILL_THE_IMMO]

u have full set dump?
so u n need to read bdm in the ecu and hc08 for the immobilizer

[KILL_THE_IMMO]

thank u i solve the problem and car start

[pizz]

Hi Mate I know it's been long time you sorted out your Ford Ranger problem. Can you help me to solve mine?

[jodge]

Hi Mate I know it's been long time you sorted out your Ford Ranger problem. Can you help me to solve mine?

what about the pictures in the other topic? :D

[den64]

Hi everyone,
Can someone please help me out? I have an ecu eeprom dump for ford ranger /mazda 2005 , I attach the dump, can you please help me out with the PIN ? and also what type of transponder i need ? 4c or 8c?

Thanks.

[lion0304]

Hi everyone,
Can someone please help me out? I have an ecu eeprom dump for ford ranger /mazda 2005 , I attach the dump, can you please help me out with the PIN ? and also what type of transponder i need ? 4c or 8c?

Thanks.

Here your pin and manual programming 2x 8C key.

See my signature for pass in PM

[den64]

Thanks a lot my friend , very helpful.

[macvernal]

Cheers, is it safe to say then that a 2006 ford Everest with a lost key cannot be programmed via obd. have thrown my Autel Maxisys, my XTool Xpad2, my Londsor K518ISE and SKP900 at it, my hair is falling out. I know its some type of Mazda system but not one of these tools has the model in that year range, they're all listing 2012-. Im trying to install an IDS thats patched onto a lapto to see if any success.I also have a SVCI unit but havent used it much, I guess it may be worth a shot?

[jodge]

short version
do you have proper soldering skills and eqipments? Do you have vvdi and vvdi chip?
If not, well forget it

long version
only the vvdi superchips are affordabe the tk5561 is pricey as hell and rare. (just a little bit)
the quick way if you take out the ecu or the immobox. For the immobox you will need a spec programmer and a hot air station. The ecu is a simple eeprom job. but NOT WITH CRAP CLIP! (mitsu or bosch mostly)
your stuff isn't support these kind of eep jobs. You will need to doing with manually. (vvdi..etc)

[macvernal]

short version
do you have proper soldering skills and eqipments? Do you have vvdi and vvdi chip?
If not, well forget it

long version
only the vvdi superchips are affordabe the tk5561 is pricey as hell and rare. (just a little bit)
the quick way if you take out the ecu or the immobox. For the immobox you will need a spec programmer and a hot air station. The ecu is a simple eeprom job. but NOT WITH CRAP CLIP! (mitsu or bosch mostly)
your stuff isn't support these kind of eep jobs. You will need to doing with manually. (vvdi..etc)
. My rework station Ive had to order a new element for as it blew, real drag for me rigt now
The SVCI unit appears to have VVDI2 support, didnt do much just read a BMW key with it using VVDI interface, and i do believe i have a few super chips lying around as well as two new keys

[alex_r_2001]

Hey Ford parameter reset is no problem for forscan application and its free.... works perfect everytime ... Just the other day programmed abs along with srs module on a 2020 ford f150 with forscan it has alot of dealer service functions... along with being able to read and edit ford as built data, they even have a database if you do not know what the as built data is... security issues no problem with forscan ,program keys adapt ecu's ... I am very impressed with there software...

[jodge]

Hey Ford parameter reset is no problem for forscan application and its free.... works perfect everytime ... Just the other day programmed abs along with srs module on a 2020 ford f150 with forscan it has alot of dealer service functions... along with being able to read and edit ford as built data, they even have a database if you do not know what the as built data is... security issues no problem with forscan ,program keys adapt ecu's ... I am very impressed with there software...


Yeah except it's not a ford. It's a a Mazda before they are implement the Ford PATS system. pre-2000 stuff manufactured until 2009 with ford badge.

[den64]

Hi,
Sorry for this,, I had a hdd crash and lost the PIN for the file, any chance you still have it and can send it via P.M. Thanks.

[lion0304]

Hi,
Sorry for this,, I had a hdd crash and lost the PIN for the file, any chance you still have it and can send it via P.M. Thanks.

Pin: 64 33 99 91