toyota alphard 2006all keys lost

[mehmet becker]

hi i was wondering if any one know witch transponder chip coms in a 2006 toyota alphard wit 2az-fe engine
i read somwhere on the net that it is a g chip if so can any one confirm that it is !

second can some one help me with a virgen file or at least get me an immo dump so i can start the car
i can supply immo dump and maby a key depending on witch key it uses

thanks and kind regards mehmet

[scanvec]

SEND MORE DETAILS OR PICTURES

[mehmet becker]

what is it that you need ?
so i can porvide the info you need ?


thanks mehmet

[ucokseparoh]

Most definitely it's a 4D67.

In some countries, if i'm not mistaken, still use 4C.

G only started in 2008.

Put your dump and key data here.. i'll help you adding the keys.

[mehmet becker]

thanks

any idea where the immo is located before i take out the whole dash baord ?

thanks mehmet

[mehmet becker]

i tried resseting the immo today generated to 60 chips to 67 but somhow i dont know it does not accept the chips so i dont know if i need origenal id67chips
but i will get to the immo and read the dump and send the key data lets see what happens

thanks mehmet

[mehmet becker]

hi heres the immo dump and key data i hope this is correct because i did not remove the chip from the board i used one of those klip on things
immo dump was already resetted so i dont know if you wil find key info
anway thanks in advanced

regadrs mehmet

[ucokseparoh]

You need key with P1 = B2 or 32 or 52 my friend. It's 4D67 , not 4D68.

[mehmet becker]

One moment i will do that

[mehmet becker]

Is this the correct data?

Thanks mehmet

[ucokseparoh]

Here you go man, try this.

[mehmet becker]

ok iwill try this and i will get back to you

thank you

[mehmet becker]

Hi i loaded the file but the car did not start it did somthing like it wanted to start for a second after the immo light came back on
Whats is the next step
Tjanks mehmet

[sadarmeng]

try this friend.... reset mode.
just make sure the indicator is solid, otherwise leave it
Auto registered.471812

[mehmet becker]

hi this file looks same as the original bin file
all numbers and letters are the same ???
what did change ?

thanks kind regards mehmet

[ucokseparoh]

Try this man.. i didn't notice that your dump was after reset.

[mehmet becker]

ok let me try this and i will get back to you guys

thanks

[mehmet becker]

Hi loaded the file this morning but still no start now the light is still blinking i accidently erased the key can i send you a different key with 32 or 52 or somthing? Problem is i dont know if ut hase somthing to do with the fact that i generate the xhips to 4d67 could that be a factor?
I use cn5 chips generated to 4d67

Thanks Mehmet

[mehmet becker]

New keys i made 1 with p1 32 and 1 with page 1 52 witch one can you use keep in mind these are generated chip 4d67 will they work?

[ucokseparoh]

Hi @mehmet , try to put pg1 32 on first position and pg1 52 on second position.

If that still didn't do the job, find another good dump which has the same part number as yours, write your keys on it then write the new file (which contains your keys in it) back to the eeprom. Put the immobox back to the car.

Turn your ignition ON (DO NOT START) , bridge pin 4 + 13 for 35 minutes.. after 35 minutes, take off the bridge and pull out your key from ignition.. then try start your car.

Wish you the best luck.

[sadarmeng]

have you tried the program? is the security indicator still blinking? or solid?

[mehmet becker]

Hi @mehmet , try to put pg1 32 on first position and pg1 52 on second position.

If that still didn't do the job, find another good dump which has the same part number as yours, write your keys on it then write the new file (which contains your keys in it) back to the eeprom


hi

thaanks but i dont undertstand what you mean by ( try to put pg1 32 on first position and pg1 52 on second position.)

where in the dump do i write these numbers ?

dump i can only find from onother immo witch i can not find aleady looked
where i stay they trow these things away

i looked at the dump you send me but sorry i still cant figure out where you wrote the new keys ( sorry i am a little new to dump programming)

can you maby explain to me

thanks mehmet

[mehmet becker]

oh sorry mister sadarmeng light is still blinking

thanks mehmet

[ucokseparoh]

take picture of your immobox, what is the part number?

[mehmet becker]

Hi here is the box number

[klaudio]

Find file with keys added, information of keys attached, write to blank transponder, it should do the job. If light still blinking that could mean that your antenna ring unit is damaged.

[ucokseparoh]

if not worked then try this.. key used here is pg1 32/52. Write this file to your eeprom.

Procedure : turn ignition ON (do not start the car !!), bridge pin 4 + 13 for 35 minutes.. after 35 minutes pull out your key and take off the bridge. Then try start your car.

if still not worked, then i give up :biggrin:

PS : take a deep look at your dump and see by your self how the key data is written there. That way you won't need asking for help for the same case in the future.

Best of luck.

[mehmet becker]

hi mister klaudio

p1 2 and3 are ok
but p4 needs to more number
what do i do with the rest
when i try to write the number in the back nd safe it writes other nubers there for me

thanks

[klaudio]

hi mister klaudio

p1 2 and3 are ok
but p4 needs to more number
what do i do with the rest
when i try to write the number in the back nd safe it writes other nubers there for me

thanks

KEY 1 ID 68
p1 32
p2 65
p3 F5 22 13 84
P4 E5 67 29 47 C5

KEY 2 ID 68
P1 B2
P2 7D
P3 FC BC E3 03
P4 EE 42 D0 5F ED

[mehmet becker]

Thank you let me try this and i will get back to you guys thanks to all of you who take there time in helping me!

[mehmet becker]

hi everyone

sorry i was out with the family for e few days

oke mister klaudio the car started fine witch the new key turned out i tried to write id 67 instead of id 68 so thank you for your help
i would also like to thank everyone els for the time and work given to me for getting this car doen
on to the next project

thanks to everyone