View Full Version : 2005 RENAULT CLIO 1.5 DCI starter will not turn
super jumbe
20th September, 2017, 01:45 PM
ECU Renault Clio 1.5DCI 8200513163 DCM1.2 DELPHI ECU
Manufacture year : 2005
8200513163
8200399038
R0410B034A
DCM1.2
DELPHI
This car did not start the immo light goes out but it just wouldn't turn the starter motor the immo light goes off, when I connect live wire to starter engine turns but will not start can some one explain what’s the fault as my obd tool will not connect to ECU, any help very much appreciated.
rideon
20th September, 2017, 05:38 PM
20 or 25 amp fuse blown- fusebox next to battery
Blown fuse usually means that the starter needs to be replaced..
yea.. reread your post with my eyes opened this time...
flooded fusebox?
super jumbe
20th September, 2017, 11:06 PM
20 or 25 amp fuse blown- fusebox next to battery
Blown fuse usually means that the starter needs to be replaced..
yea.. reread your post with my eyes opened this time...
flooded fusebox?
Checked all fuses ok, any other solution?
cotton1981
21st September, 2017, 12:44 AM
Check The switch feed to starter motor by using a multimeter.
albertros
21st September, 2017, 09:48 AM
Hi,
put a jump pack on the bat pos+ and negative on engine block
super jumbe
21st September, 2017, 02:59 PM
I am going to fit new starter tomorrow will keep you posted...
rideon
21st September, 2017, 06:46 PM
No point changing the starter ....
Do you hear the usual egr/throttle.noises under the hood when ignition is on?
Meat-Head
21st September, 2017, 09:41 PM
ON TOPIC:-
Had one the same fault code was like "ze fluid nil poi"
Or something just as good.
Opened le hood, no "Eau" and "Huile" nil poi
Refilled, shouted "ze kontact" and as tge lone stranger wiuld say,
hi ho silver away
doctore
21st September, 2017, 09:59 PM
ECU Renault Clio 1.5DCI 8200513163 DCM1.2 DELPHI ECU
Manufacture year : 2005
8200513163
8200399038
R0410B034A
DCM1.2
DELPHI
This car did not start the immo light goes out but it just wouldn't turn the starter motor the immo light goes off, when I connect live wire to starter engine turns but will not start can some one explain what’s the fault as my obd tool will not connect to ECU, any help very much appreciated.
check 4 black reley 1 and 2 its for start and ecu uch ,and check under this reley upsade down instalation plus and minus if this reley dont have power no comunication
super jumbe
21st September, 2017, 10:37 PM
I might as well have a week off all the cars came in garage this week towed by RAC looks like all are hear to stay paying the rent from my pocket.
super jumbe
27th September, 2017, 10:07 AM
Ok got back this time I need to get this car on road replaced new starter motor still the same, now I can see red stop sign on the dash, I have replaced new fuse box not getting any were any more suggestions!!!
Louislesinge
27th September, 2017, 10:24 PM
Hello,
You mean now starter runs, engine turns but doesn't start and a red STOP light flashing goes on after several times of testing start?
If the red light "stop " flashes, it probably means there is a problem about the high fuel pressure. ECU must be interrogated to check faults.
First thing I think is you must remove the fuel filter, shake it and put the residual fuel into a transparent plastic cup, then walk a little magnet below the cup to look for steel dust that could mean the pump is broken.
Regards,
Meat-Head
27th September, 2017, 10:28 PM
Err you HAVE cut the lucar off the white wire and replaced with new crimp?
also what does diagnostic computer say?
super jumbe
28th September, 2017, 06:55 PM
Had enough told customer take it else were….
Powered by vBulletin® Version 4.2.5 Copyright © 2025 vBulletin Solutions Inc. All rights reserved.