Alfa 159 - 2006 - 1.9 JTDM 16V 110kW/ 1037377871/ - Needed

[Emre2blue]

HW: 0281012144
SW: 1037377871
Spare: 55205068

I need damos % A2L files full of them need to start my DIY tuning. I have the original file. And I have the 260HP file that is on the car right now. And I needed to fine tune it. But I could not find a proper location? Please help

[johak]

check out this damos

[Emre2blue]

Are "EDC16C39" & "........C9" same ?

I was especially looking for my gauge pressure settings. You know Alfa 159 has already boost pressure gauge inside. My boost is more than 2 bars. And I could not see it inside. I want to find those locations.

[johak]

this is edc16c39

[Emre2blue]

This file is from opel ?

[johak]

this file is from fiat

[Emre2blue]

159 Damos is hard to find right? This file does seems to be 147

[Emre2blue]

@johak , I've sent you PM, please check...

[NOX]

Hi friend, :stung::stung:
you need to linearize the sensor on the map
and mount a 4 bar sensor

[Emre2blue]

Can you explain more ? I know that ~0.2V is like 0 bars. And ~4.89V is about 3 Bars Absolute. And I have a margin of maximum 2 bars of boost. I know from the file. But in the gauge it is only 1.6 Bar of boost.
I know it. There is a map location it says something like this

Pressure = 1000 - 1200 - 1400 - 1600 - 1800 - 2000 - 2200 - 2400 - 2600
Duty = %11 - %22 -% 33 %44 - %55 - %66 - %77 - %88- %100

Only for the gauge.

[NOX]

you only want to increase pressure?

then it is sufficient to increase 1e1370

[NOX]

do you have a 260HP (file Tuning) with 1.6 bar of pressure? mm3? afr? time opening were calculated? pid?
send grafic dynotest please

[Emre2blue]

@NOX , I've sent PM, The car was overboosting over 2.5bar maybe ?

[Emre2blue]

Tuning List is here

1) 0445 110 308 Injectors - brand new
2) GTB2060VKLR turbo with 10+0 GEN II Billet wheel
3) 70mm Downpipe + 70mm whole exhaust system + custom mid silencer + two custom back silencer
4) Ported Head + New 4 angled valves to feed more air easily
5) Custom Billet Intake with bigger plenum + 72mm Input without Throttle body
6) Custom Billet Exhaust Manifold 5mm Thickness 304TI - Same volume as orgiinal manifold to keep the spool fast.
7) Custom 4Lt Water2Air Intercooler design
8) 17" Standart Wheels with M32 Gearbox. 225-25-17 Rıms
10) Balanced Crank
11) Whole New engine
12) New head from 2008 car, It uses different glow plugs only in "Beru"
13) New Pistons
14) Same Rods
15) +1 Bar Oil Pump
16) Now the car has original MAF & MAP sensors. But I have new 80mm MAF and 3.5Bar MAP sensor

17) I want to put 2.4Lt JTDM - MAF 0 281 006 048
18) I want to put 3.5 BAR MAP sensor - 0 281 002 456

19) I don't have EGR valve at all. Full EGR system is in the garbage.
20) I don't have SwirlValve
21) I don't have Throttle Body.
22) I don't have DPF. I only make a fake shaped middle silencer. And put the sensors on it. To con the government

I have %10 more injection quantity at injectors. And the reMap is opened up to %15 more quantity. with 1750Bar CR pressure.

[NOX]

Tuning List is here

1) 0445 110 308 Injectors - brand new
2) GTB2060VKLR turbo with 10+0 GEN II Billet wheel
3) 70mm Downpipe + 70mm whole exhaust system + custom mid silencer + two custom back silencer
4) Ported Head + New 4 angled valves to feed more air easily
5) Custom Billet Intake with bigger plenum + 72mm Input without Throttle body
6) Custom Billet Exhaust Manifold 5mm Thickness 304TI - Same volume as orgiinal manifold to keep the spool fast.
7) Custom 4Lt Water2Air Intercooler design
8) 17" Standart Wheels with M32 Gearbox. 225-25-17 Rıms
10) Balanced Crank
11) Whole New engine
12) New head from 2008 car, It uses different glow plugs only in "Beru"
13) New Pistons
14) Same Rods
15) +1 Bar Oil Pump
16) Now the car has original MAF & MAP sensors. But I have new 80mm MAF and 3.5Bar MAP sensor

17) I want to put 2.4Lt JTDM - MAF 0 281 006 048
18) I want to put 3.5 BAR MAP sensor - 0 281 002 456

19) I don't have EGR valve at all. Full EGR system is in the garbage.
20) I don't have SwirlValve
21) I don't have Throttle Body.
22) I don't have DPF. I only make a fake shaped middle silencer. And put the sensors on it. To con the government

I have %10 more injection quantity at injectors. And the reMap is opened up to %15 more quantity. with 1750Bar CR pressure.


you spent a lot of money!!!

[Emre2blue]

I made all of them by myself. All the Billet parts. I have CNC, and design them.

Li ho fatti tutti da soli. Tutte le parti del Billet. Ho CNC e li progetta.

[Lucian189]

here you go ..
map pack in english for the necesary tuning maps

[Emre2blue]

Is there a Version 2?

[Lucian189]

Thats what I have
Does not help?
It should ..

[NOX]

Hp pump CP1H R70?

[Emre2blue]

Yes, stock

[NOX]

Yes, stock

No good friend!

[Emre2blue]

Hi , again

Can you help me a little more. I have to take some data from 2.4Lt ECU, I have a file, but not damos, or Map pack, My map list is good for me some of them missing but so much good information is there for me...
Anyway do you have 2.4Lt damos ?